ender 5 plus glass bed 3d models

This is a remix of the original mounting plate. ... This was changed to both give a better wire strain relief post and to allow it to mount on the Ender 5 plus carriage plate without hitting the left belt tab.

Ender 5 Plus Filament Roller ====================== Simple "plug-on" Spool Holder with two 608zz (8mm x 22mm x 7mm) ball-bearings. ... It supports spools with a inner diameter of at least 72mm and a width of max 72mm.

A simple block riser I put together to handle adding on NEMA Z Dampers to my Ender 5 Plus. ... This doesn't change the supported Z print area as it doesn't change the coupler configuration.

I didn't create this from scratch. ...The original work was done by dinesh612. They put in all the effort. My contribution was adding the Crealty Dragon and the Ender 5 Plus content to it.

Hello everyone, I made 2 heat towers to test an ender 5 plus with PLA, ABS, PLA carbon fiber, TPU and more. I made some G-codes with some variables : Temperature, fan% and speed. I made it with simplify 3D and i put the parameters i used in the...

I've also completely insulated the bottom of the heated bed, as only the center is on a stock Ender 5 plus. And I've upgraded to silicone spacers instead of springs and also upgraded to Aluminum leveling wheels. After having problems sourcing a...

HOW I MAKE IT: <iframe width="560" height="315" src="https://www.youtube.com/embed/RpIH-jXLHm8" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe> MATERIAL: ...

No supports, adjustable head angle, two M3x20 Feel free to support me with DOGE ;) DSmeW6UgGQEGP4gbfWfYAeP6aX3U1yhGju

Customized version of https://www.thingiverse.com/thing:3507663 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3507663

Customized version of https://www.thingiverse.com/thing:3507663 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3507663

This is a remix of https://www.thingiverse.com/thing:4548894 That was remixed from eric-anastas Satsana for the Ender 5 Plus. I added a taller wire strain relief and adjusted it to better fit around the belt protrusions. I have printed it and it is...

This adapter makes it possible to fit a SKR 1.4 board into an Ender 5 plus without cutting a hole in the case. ... Hardware required: 4 x 3mm screws When its printed, you take a 2,5 mm drillbit and drill the 4 four holes for the SKR board and the screw...

Filament guide for my Ender 5 plus, have my spool mounted on the side but the filament was making a 45 degree angle into the filament sensor. Not good. Made this to make sure filament enters at a more perpendicular angle. Mounts on stock Ender 5...

Ender 5 Plus Hemera Mount and Linear Rails https://www.thingiverse.com/thing:4163017 Remix of Sidewinder-X1-V2-Nighthawk V6 with instructions https://www.thingiverse.com/thing:4169959 Bottom Filament Feed for Hemera and Ender 5...

Simple design to cover the LCD screen on the Ender 5 Plus. I no longer use the touch panel on the printer, as I use Klipper. I added my own custom logo on my original print, but created a blank panel and one with the Ender logo to share. To get the...

* Measure your offset from the print nozzle to the laser center for X and Y >* Mine was inline on X and -55 on Y * You need to account for the offset in most of the software for creating the gcode * The "Ender 5 Laser Origin.stl" replaces the clip...

Leveling feet for the Ender 5 Plus. A full set will require the following components: (2x) Part1-Mount-LH, (2x) Part2-Mount-RH, (4x) Part3-Foot, (4x) Part4-JamNut, (8x) M4x10 screws, (8x) M4 T-slot nuts. ... You can stick some foam tape or rubber dot...

This holder consolidates all of the hex keys, wrenches, and the screw driver that comes with the Ender 5 Plus. It also has an extra slot to keep a razor blade in. ...The lid may be a tad loose depending on your printer, so you can add some tape to add...

The Ender 5 Plus can be elevated by placing this foot under it, utilizing the stock feet provided. The foot features a tapered recess at the top that cradles the stock feet in place, preventing them from slipping or tilting. ...With this riser...

Ender 5 Plus filament guide enables effortless spool movement outside the printer for enhanced accessibility. A secure attachment is ensured by zip-ties tied through a sturdy tube. ... Print time on standard settings typically ranges from two and a...

The workbench I wanted to set my ender 5 plus up on was a bit smaller front to back than the footprint of the printer, so I made this doohickey. Just shove it under the feet along the edge of the surface it should accommodate the overhang. ... Use...

This is a remix for an Ender 5 Plus - will require 2 of these pointing at the printed object. ... Will be printing in the next day or two to test - any issues I will update this Printing on my E5+ using PETG as that is what I currently have it set...

I relocated the electronics enclosure on my ender 5 plus to sit outside my enclosure. There is a small fan on the bottom of the box that is designed to cool the electronics components inside, so these feet lift the box off the table slightly...

Summary This is a filament lead in tube (Bowden) end holder for Ender 5 Plus direct extrusion modifications. It is designed to hold the end of the filament lead in tube from the filament break detector to the direct extruder. The filament bracket...

... addition to mount LED strips facing to the print. ...Fits nice on my Ender 5 Plus. ...Maybe also on other Printers Before printing, lay it on the back in your slicing software to avoid support-printing Printing: Infill 10% Speed 100%

This thing was created using Tinkercad. ...Edit it online at https://www.tinkercad.com/things/b8Y8tFp5kVM. This is a remix of the original design, modified for use with the Ender 5 Plus. ...Simply remove the top bar to enable smooth sliding motion!

a simple low profile cable clip of the ender 5 plus hot end cable aka 1/2" split loom. ... for assembly: (2) M5x10 screws (2) M5 T nuts (1) 8" cable tie Second version to re-use shorter screws Tip: Add a second clip for added support

Redesigned X Axis opposite side bracket to allow for referencing on glue up Additional Parts Needed: SonOvaSailor's Design: Print 1 - Heat bed plug link and 4 Chain Link Cover Long  found here https://www.thingiverse.com/thing:4570302/files...

The Ender 5 Plus struggles with wirestrain management just like its predecessor, causing significant problems. This solution tackles this issue head-on by securing the pillow block and axis assembly between its sturdy braces without disrupting motion...