ender 5 plus glass bed 3d models

This is a Creality Ender 5 Hot Bed Cable Relief that I Remixed in TinkerCAD. I took the zip tie design and designed an attachment around it. The reason I designed it is because a lot of the other designs took way too long to print and took extra...

Support for the cable from the bed to the controller.

I felt a better approach was to move the bed up, leaving the rest of the printer stock (It's also a lot easier to fit / print :) ). These go under the bed bracket, so you'll need four. It raises the bed height by 10mm. ... I printed these at 70% in...

I felt a better approach was to move the bed up, leaving the rest of the printer stock (It's also a lot easier to fit / print :) ). These go under the bed bracket, so you'll need four. It raises the bed height by 10mm. ... I printed these at 70% in...

If you're considering these prints, I would strongly advise using auto bed leveling and double-checking by manually leveling your bed and taking precise measurements to confirm uniformity across all four corners. If discrepancies arise, simply adjust...

Designed to support the heat bed cables to help take some of the strain from the solder joints of the cables when bed is at the high positions. Undo the 4 pcs m4 screws holding the linear guide bearing, slide it between the guide bearing and...

I remixed the Bed Rod Holder to allow attachment from the bottom of the extrusion, instead of the side. This allows for additional clearance for a left mounted probe on a long hotend like a volcano. ... I now only need 2.5mm of clearance to avoid...

... is possible to 'hide' the zip ties. I remixed the feet so that they would provide maximum support. I use 100mm M4 bolts for the bed, they extend easily through the assembly. ... Hardware used: 4 x 50mm M5 4 x 8-10mm M3 4 x Small zip ties

The upper front bar is lowered with 5,8 cm. Shorten the 2020 bar with a mitter saw and make a new thread (M5) in the bar. I use the original brackets and screws. I made 2 types of end cap for the 2020 (with a short and a long middlepoint). ... I made...

this model is designed to hold the glass bed of your ender 5 pro 3d printer in place.

Glass Bed Clip designed for side mounting for Ender 5. ...7.2mm space, sadly the corner one didnt fit near the bed cables so i created this one.

... the adhesion despite the clips' snug fit. Below is the link to the Ender Glass Bed on Amazon: https://www.amazon.com/Creality-Platform-Tempered-Upgraded-235x235x3mm/dp/B07NVFSQGN/ref=sr_1_5?dchild=1&keywords=creality+glass+bed&qid=1591461771&sr=8-5

Clips securely fit a 4mm glass bed on the Ender 5 printer, ensuring the printing process occurs with the arms positioned upwards, resulting in an overall gap of 8mm.

Since the Ender 5 bed moves up and down very slowly, the clips do a great job of keeping the Glass bed pressed close to the heatbed and level. After numerous heating sessions and prints, the clips are still performing well for me. One problem is...

Here's my current build plate setup: * Original build plate * Original magnet pad (in case I ever want to switch back to the original bed) * Glass bed from Creality It takes about 25 minutes to print each corner. To mount the glass bed, follow...

Made a side bracket as a corner piece could not be placed where the bed gets hooked up.

For the Ender 5 Plus, you need to use the risers, which attach to the bed assembly crossbeams with T-Nuts and capture the tram wheels. I designed these risers to accommodate up to a 12mm OD spring, so feel free to use 30mm medium loads. You will...

Ender 5 Plus Heated bed cabel holder. ... Support: No

Modified https://www.thingiverse.com/thing:4119720 to fit the 4mm glass bed and cut the side not to hit the fan shroud

Ender 5 Plus bed cable support. Wanted one which was simple, solid and didn't require additional parts. To install just remove the two screws on the bed frame, slide the support in and reinsert the screws. ...The screws don't touch the support, they...

However, the following text has been rewritten: The Enders 5 Plus bed is connected to a cable that keeps it safe. ...To secure the cable, just snap it into place in the square hole and tie it up with some cable ties, just like you see in this picture.

This Remix is a cable support bracket for the hot bed cable on an Creality Ender 5 series with the Ender Xtender Upgrade. I redesigned this for the 500x500 bed, but it will work fine for the 400x400 bed. ... Parts: 2 - M4 Nuts 2 - M4x25 Socket...

This Remix is a cable support bracket for the hot bed cable on an Creality Ender 5 series with the Ender Xtender Upgrade. I redesigned this for the 500x500 bed, but it will work fine for the 400x400 bed. ... Parts: 2 - M4 Nuts 2 - M4x25 Socket Head...

This is a cable support bracket for the hot bed cable on a Creality Ender 5 PLUS. Parts: 2 - M4 Nuts 2 - M4x25 Socket Head Cap Screw 02/21/2020 - A taller version, 50mm higher by special request, was added. 02/10/2020 - V2 added, same as original...

When using the Bondtech DDX on an Ender 5 Plus, the DDX will not clear the Creality bed rod holders. Bondtech sells a bed rod holder that solves this issue. They also allow you to download the file and print it yourself:...

Its thanks to him that my 5 plus has become a reliable printer now. I had an issue with my Z axis coming out of sync on one side causing my bed to droop and i happened to come across his file which had solved my problems. The files here are my own...

Very quick and easy bed leveling test. ...The squares are 20mm each placed on every corner and middle of the bed. 

8) Mount the bed assembly to the 2020 extrusions you just added with the 4 factory M4 bolts and Tnuts that you removed form the top. 9) Use the photos above to put together the gantry with the 2 2020 463mm that you cut and tapped with the M5...

I needed something more durable than paperclips to hold my Ender 5's glass bed in place, so I created these custom retainers using Sketchup and printing them out. Initially, I had measured the length at .255, but later adjusted it to .265 (6.75mm) to...

Ender 5 plus bin