ender 5 plus fan 3d models

PLA Temp tower for the Ender 5 Plus. Speed: 60 mm/s Layer Height: 0,2 mm. Retraction: 1 mm. ... Acceleration: 250 mm/s2

Ender 5 Plus Tool Holder =================== Remix of https://www.thingiverse.com/thing:3655629 from [Kyle Finnigan](https://www.thingiverse.com/TrigoKlei). It's a tool holder for all Ender 5 Plus stock tools which can be clipped on the vertical...

... ... J'ai repris les dimensions. J'espère que cela vous servira. ___________________________________________________________ English During transport a bracket of my Ender 5 Plus was broken. I resumed the dimensions. I hope it will serve you. ...

Remix of the Satsana air duct to allow for the installation on and ender 5 plus carriage without causing a problem with the Y end stop or the belt tab. Pairs with my other file for installing the Mosquito hot-end onto the ender 5 plus.

Français Pendant le transport, une équerre de mon Ender 5 Plus a été cassée. J'ai repris les dimensions. J'espère que cela vous servira. English During transport a bracket of my Ender 5 Plus was broken. I resumed the dimensions. ...I hope it will serve...

Hello everyone, I made 2 heat towers to test an ender 5 plus with PLA, ABS, PLA carbon fiber, TPU and more. I made some G-codes with some variables : Temperature, fan% and speed. I made it with simplify 3D and i put the parameters i used in the...

This is a V6 mounting with custom cooling for the Ender 5 and 5 Plus. Currently it supports 4020 fan blowers, but Im planning to add more variants in the future. Also direct drive mod for this is in progress - it will probably work with this parts...

This is a V6 mounting with custom cooling for the Ender 5 and 5 Plus. Currently it supports 4020 fan blowers, but Im planning to add more variants in the future. Also direct drive mod for this is in progress - it will probably work with this parts...

A simple block riser I put together to handle adding on NEMA Z Dampers to my Ender 5 Plus. ... This doesn't change the supported Z print area as it doesn't change the coupler configuration.

I didn't create this from scratch. ...The original work was done by dinesh612. They put in all the effort. My contribution was adding the Crealty Dragon and the Ender 5 Plus content to it.

Screen cover for ender 5 plus. Fits perfectly right in the ridge around the screen. ...I would print in black to completely block out the light but white filament makes for a cool effect.

This is a remix of the original mounting plate. ... This was changed to both give a better wire strain relief post and to allow it to mount on the Ender 5 plus carriage plate without hitting the left belt tab.

Ender 5 Plus Filament Roller ====================== Simple "plug-on" Spool Holder with two 608zz (8mm x 22mm x 7mm) ball-bearings. ... It supports spools with a inner diameter of at least 72mm and a width of max 72mm.

This is an adaptable upgrade for the Ender 5 Plus featuring directional guidance to fine-tune your print bed, which can also be compatible with the CR-10S Pro.

... 0,0 of your print nozzle. >* You still need to account for the Y offset of the laser mount. Notes: --------------------- * On the Ender 5 Plus the laser can attach directly to the cooling fan wire (blue/yellow) without opening the case. ...

This is a remix of https://www.thingiverse.com/thing:4548894 That was remixed from eric-anastas Satsana for the Ender 5 Plus. I added a taller wire strain relief and adjusted it to better fit around the belt protrusions. I have printed it and it is...

i have moved the position of the cr touch mount (witch also works with Bl touch i run one) to the oposite side of the tool head to maintain the ender 5 plus position the base plate and cr touch mount and wire cover are different. also have...

This adapter makes it possible to fit a SKR 1.4 board into an Ender 5 plus without cutting a hole in the case. ... Hardware required: 4 x 3mm screws When its printed, you take a 2,5 mm drillbit and drill the 4 four holes for the SKR board and the screw...

Filament guide for my Ender 5 plus, have my spool mounted on the side but the filament was making a 45 degree angle into the filament sensor. Not good. Made this to make sure filament enters at a more perpendicular angle. Mounts on stock Ender 5...

Originally it was remixed by https://www.thingiverse.com/thing:4548894 That was remixed from eric-anastas Satsana for the Ender 5 Plus this specific is remixed from remix created by PUCK81...

Ender 5 Plus Hemera Mount and Linear Rails https://www.thingiverse.com/thing:4163017 Remix of Sidewinder-X1-V2-Nighthawk V6 with instructions https://www.thingiverse.com/thing:4169959 Bottom Filament Feed for Hemera and Ender 5...

Simple design to cover the LCD screen on the Ender 5 Plus. I no longer use the touch panel on the printer, as I use Klipper. I added my own custom logo on my original print, but created a blank panel and one with the Ender logo to share. To get the...

Pattern to see which corner needs to be set with Ender 5 Plus. Set your layer height to 0,2mm and you will have 2 layer. For bed equale or larger then 350mm x 350mm. ... *** WARNING*** Paper clip of the front left corner must to be move to...

Leveling feet for the Ender 5 Plus. A full set will require the following components: (2x) Part1-Mount-LH, (2x) Part2-Mount-RH, (4x) Part3-Foot, (4x) Part4-JamNut, (8x) M4x10 screws, (8x) M4 T-slot nuts. ... You can stick some foam tape or rubber dot...

This holder consolidates all of the hex keys, wrenches, and the screw driver that comes with the Ender 5 Plus. It also has an extra slot to keep a razor blade in. ...The lid may be a tad loose depending on your printer, so you can add some tape to add...

Ender 5 Plus filament guide enables effortless spool movement outside the printer for enhanced accessibility. A secure attachment is ensured by zip-ties tied through a sturdy tube. ... Print time on standard settings typically ranges from two and a...

... addition to mount LED strips facing to the print. ...Fits nice on my Ender 5 Plus. ...Maybe also on other Printers Before printing, lay it on the back in your slicing software to avoid support-printing Printing: Infill 10% Speed 100%

a simple low profile cable clip of the ender 5 plus hot end cable aka 1/2" split loom. ... for assembly: (2) M5x10 screws (2) M5 T nuts (1) 8" cable tie Second version to re-use shorter screws Tip: Add a second clip for added support

This is a remix for an Ender 5 Plus - will require 2 of these pointing at the printed object. ... Will be printing in the next day or two to test - any issues I will update this Printing on my E5+ using PETG as that is what I currently have it set...

I just made this quick thing, it covers the metal sliders on the Ender 5 Plus the bed uses to go up and down evenly. Doesn't affect the way it works, just makes it so you can change the colour from a metal to what ever colour you want. ...It fit...