ender 5 plus enclosure 3d models

I upgraded to a dual gear extruder on my Ender 5 Plus and the alignment for the filament sensor was off. This is a 10mm Spacer that aligns the filament sensor for the all metal dual extruder found on amazon. ...

Here is the rewritten text: A simple clip box designed for the Ender 5 Plus, I've included the step file, allowing you to easily modify its dimensions as needed.

Ender 5 Plus Micro Swiss Direct Drive Palette Connector If you find it usful and would like to donate anything here is my PayPal https://www.paypal.com/biz/fund?id=QPA2FV7N6SRRC

A strain relieve for the ender 5 plus. The strain relieve is for the bowden tube and electrical wires to the extruder. It is attached with two T-nuts. ... Hope you like it!

The Ender 5 Plus mount is designed to accommodate the stock bracket that holds the extruder in place, specifically for direct drive configurations that utilize a Bowden tube for feeding the filament directly to the extruder.

Simple bracket to put a BigTreeTech GTR v1.0 into your Ender 5 Plus. ... Also has a an alternate mosfet mount that can piggyback or just slice it in with an editor.

simple bracket for mounting the MKS Monster 8 motherboard in the stock Ender 5 Plus electronics case.The mosfet has to be relocated for it to fit.

This is a holder that lets you reduce the strain on bowden and cables leading to the hotend on a back side of the printer near extruder. ... Sliced model as a gcode for Creality Ender 5 Plus included.

All of the other 3 corners fit perfectly on a Ender 5 Plus... This corner did not and I could not get the "silent" home to work.. ...So I recreated it with the end stop in the factor location

Designed some 3D printed Oldham Couplers for my Ender 5 Plus. The ones available didn't match up with the bolt pattern on the 5 Plus' lead screws. Suggest Printing at 100% infill with 0.12 layer height and 4 walls. ... Uses M3x8mm to attach to...

Creality Ender 5 Plus 2020 2040 Cable Covers These cable covers are designed to fit any 2020 or 2040 sections. We tested these parts with a 100% infill, and they performed well. The parts themselves are thin and fragile, but with proper care, they...

This adapter is for mounting the BTT Manta M8P in the Ender 5 plus case. This places the USB, SD, etc ports in the vicinity of where the stock board positioned them. You will need to cut a hole in the stock Ender 5 plus case if you intend to access...

Designed in Fusion 360.This is a work in progress of an electronic box for my Creality Ender 5 Plus 3D printer. Goes on the top left of the printer and allows for easy maintenance to the motherboard and lcd screen. ...The bottom model is done though...

Ender 5 Plus X axis Linear rail with a BMG direct drive. Made using Ender 5 plus linear rail modification from: https://www.thingiverse.com/thing:3960105 and added a BMG direct drive and a cable management on the side. Print instructionsCategory: 3D...

Two pieces that fit inside each other and squeezed tight with zip ties and attached to the frame with 2 x M4 bolts and T-nuts Update 01/04/2021: Thicker version added as 'Ender 5 Plus Rear Cable SupportV2.stl' Original...

This is a case designed for use with the factory OEM Ender 5 Plus frame and electronics enclosure. It will hold a BigTreeTech (BTT) PI TFT70 touchscreen for use with Klipperscreen or Octoscreen. This is not designed for the Raspberry Pi to be...

Custom electronics enclosure for Ender 5 Plus printer. Takes standard Meanwell power supply and heated bed MOSFET & standard touchscreen. Designed to work with either SKR 1.3/1.4 motherboards. Due to their size, they need to be printed on the E5...

I wanted to reroute the hotend cable within the Ender 5+ enclosure (on the same side as the PTFE) but the original instructions were a bit too lengthy for this specific position, protruding too far toward the print bed. The only modification was...

Simple remix to allow the bracket to work with the Ender 5/ Ender 5 Plus carriage. The ender 5 plus belts are position so that the ferrules on the end stick out the front of the carriage. This modification allows space for those ferrules. ... You...

Whether you're a seasoned 3D printing enthusiast or just starting out, these custom-made feet can help take your prints to the next level and unlock new possibilities with your Creality Ender 5 Plus. Incorporating Squash Ball printer feet into your...

This is a side frame mount that I designed for the Palette 2S to attach to the Ender 5 Plus. The file was designed in Fusion 360 and printed in PLA with 30% infill. I attached the included Palette 2S mount to the printed mount using self tapping...

I'm employing it successfully in conjunction with a Bigtreetech SKR v1.3 board that's been mounted using a simple adapter; as you can clearly see from the images, this configuration will definitely fit inside the Ender 5 Plus case. ...To my knowledge,...

Ender 5 Plus Cooler =============== This is an Ender 5 Plus Cooler mount for two 5015 radial fans and one 4020 fan without any change to the BLTouch or the Hotend. Only modification required is to the fan connector cables. I suggest to use terminal...

... can install the box more easily. Print Settings Printer Brand: Creality Printer: Ender-5 Plus**Rafts:** Doesn't Matter Supports: Yes**Resolution:** 0,2 Infill: 20% **Filament:** Doesnt Matter Doesnt Matter Doesnt Matter Category: 3D Printer Parts

The one included with the kit is for the Ender 5 (non Plus) and did not line up correctly. Micro Swiss support sent me this STL and gave me the ok to Share it an post it here. ... Thanks to Micro Swiss support for supplying this so quickly and...

I prefer 3D printer accessories that don't need extra hardware, so I designed all mine to simply snap onto the 2020 aluminum frames of my Ender 5 Plus printer. This pliers holder snaps right on and stays put, keeping it within easy reach as I always...

Creality Ender 5 Plus 2020 2040 Cable Covers Will suit any 2020 / 2040 sections (This was 100% infill) All parts are thin and weak but with care they work well. Remove using a paint scraper under the edge near the clips and twist carefully. Creality...

Custom electronics enclosure for Ender 5 Plus printer suitable for BigTreeTech GTRv1.0 and M5 boards. Is designed to take standard Meanwell power supply, Creality heated bed MOSFET, Creality standard touchscreen (others will also fit), BigTreeTech...

... the clip stress area. Print time 2:46 using PETG Head temp 240C, bed temp 80C I found the original liked to lift one end with a lower bed temp and thinner profile. Stock Ender 5 Plus glass bed (smooth side) with BedWeld applied. ...

This is an external mount for the 500W Meanwell power supply ( RSP-500-24 ) that comes with the Ender 5 Plus. It consists of a top cover, bottom cover, and power switch/plug holder with a cover. The power switch/plug holder uses the existing power...