ender 5 plus enclosure 3d models

I wanted to mount a Voron M4 extruder to my Ender 5 Plus while retaining the stock filament runout detector so I designed this piece to mount it much like the stock extruder. ... You will need 4 M3 screws and nuts to mount the runout sensor, 3 M5 screws...

This is a magnetic snap-on case for the BTT TFT24 display to attach to a Ender-5 Plus printer equipped with a BTT SKR v1.3 or v1.4 board. Four magnets are holding the case onto the existing LCD cutout. Magnets: 4 pcs 10mm diameter and 2mm...

... this one in PLA+ for testing. Decided to go another route, but if I had kept it I would've reprinted in PETG. Printed great on my Ender 5 Plus, I added 3 perimeters(for a total of 6) and 10% infill(for a total of 25%) for some added strength.

I designed this to replace the boring black limit switch covers on my Ender 5 Plus with no additional hardware needed. They will also work on limit switches on other Creality machines, but you will need two M3x14 screws. I have test printed this...

Namely: https://www.thingiverse.com/thing:4437226 https://www.thingiverse.com/thing:4492841 This fan duct will fit over the original BLTouch mount and the X Axis belt on the Ender 5 Plus WARNING This will push your part cooling fan right about 1cm. I...

I recently purchased a new extruder gear for my Ender 5 Plus. It's a knock off Bondtech Geared extruder, but works well. However the new gears put the filament path about 9mm higher than stock. I designed a simple spacer to accommodate the increased...

Since I'm not using the stock Ender 5 plus display, I've remixed a BTT TFT35 mount with a 40mm fan grille. Just an easy no case modification required to add another cooling fan to the case. ...Should fit any 40mm fan, screws for fan mount are M3 length...

hello this is my modded led light bar holder for my ender 5 plus but will fit others on the main bracket i used 50% infill and on the led holder i used 100% infill this is to fit the led which was from amazon this is the link...

I wanted a sleek light bar for my Ender 5 Plus, but every standard LED strip didn't fit, so I grabbed xqqqqme's clips and gave them a makeover to match LilTrublMakr's bar perfectly. I removed the v-slot modification and here's what I came up with -...

Remix of Giuliano Moschini's fanshroud assembly for the MicroSwiss Direct Drive for the Ender 5 Plus. I trimmed it down if someone wants just a strain relief. I added channels for 2.5mm smaller zip ties. I printed this on my CR-20 Pro with a .2mm...

A simple wire support for your Ender 5 Plus hotplate should fit others just as well. Secure it with cable ties under the hotplate mount right next to the bed leveling screw. The first test print was made with HIPS, extruder temperature at 240C, and...

Bretware Ender 5 PLUS Chain System Please subscribe to our Youtube channel https://www.youtube.com/channel/UC-dZpDgCGSf7w-vZWgO2Nsg/videos Uses Johnniewhiskey Ender 3 chain To be used with the following, Chain and covers...

Dan's tutorial and parts can be found here: https://e3d-online.dozuki.com/Guide/Hemera+Creality+Ender+3+(CR-10)+Upgrade./107?lang=en For my Hemera conversion, I utilized the stock Ender 5 Plus Thermistor, Heater, and Fans and purchased a longer...

You may locate the crossbar at any height you find suitable for your setup.Also consider printing the End Covers that protects you from the sharp edges that get exposed when you relocate the crossbar:...

I wanted an LED strip light for my Ender 5 Plus, but all I found was this one for the standard Ender 5: https://www.thingiverse.com/thing:4125317 Front and rear lighting is nice, but it wasn't wide enough for the Plus so I needed something bigger. At...

Not sure where the original design came from but I have it on my ender 5. Bought a 5 plus and wanted to add similar protection to the BL touch. Quickly discovered that I needed to add a few mm to it in order to maintain the clearance of the rail...

This spacer is specifically designed for users who have installed the BondTech BMG extruder on their Creality Ender 5 plus and still want to utilize the filament run-out sensor. *Update* I initially provided an incorrect spacer, which I promptly...

Gehäuse für das Bigtreetech TFT70 v3 um es an den Ender 5 Plus zu verwenden. Die Bodenplatte habe ich mit 5 Magneten 1x8mm die in die Aussparungen eingeklebt werden befestigt, somit kann man sie jederzeit abnehmen. Man Kann Sie aber auch mit...

This is a remix of a item I found here that was made for another extruder so I adapted it for the Ender 5+ Plus stock/upgraded version. I cannot find that design to give the original designer credit. I will update if someone else finds it and...

A simple tool for you to align the dual z axis on your Ender 5 Plus. Print 4 of these and place on the smooth rods. You can print the block in solid or without top and bottom. If you only have 1 stepper driver for dual Z and cannot preform Marlin...

I got tired of trying to get the whole bed carriage level on my Ender 5 Plus. It tends to sag a little when the power is off, and I struggled to get it back to level every time I powered it on. This simple solution fits on top of the bed frame and...

Extended version of trays to fit the Ender 5 Plus Original parts still required from: https://www.thingiverse.com/thing:4116655 Changes: X-Axis screw holes reduced for M3 screws X-Axis Right, modified to fit around endstop, so no need to change....

Tube guide for the Creality Ender 5 Plus to avoid contact with the drive axis. The tube with the wiring for the hot end slides between the drive axis and the frame. The part is mounted on the rail with two T-nuts and M5x12 screws. The tube can be...

... of the clip. The original clips kept popping out or falling off the extrusions with ease, so I gave them a makeover by remixing the Ender 5 Plus Wire Clip design. ...This new version fits more securely and stays put even when accidentally bumped.

This is a top mount filament spool holder remix specifically for the Ender 5 Plus. The original from Les73gtx is: https://www.thingiverse.com/thing:4536704 I made this one taller and added an angle at the same time in order to move the spool...

This is a revised version of an exceptional Ender 5 Plus Heat Bed cable strain relief. It prints quickly and functions flawlessly. However, additional hardware - M3 screws and T-nuts - are required. T-Nuts can be found at...

One was for Ender3 and the other was a rough Ender 5 Plus design that needed jesus. This should be usable with the Ender5+ with little to no modifications to your printer. It uses the default hardware. ...BLTouch mount is about 5mm to the left of the...

remixed for ender 5 plus with microswiss direct drive kit. notch added to clear belt mounting. ...slightly larger clearance hole for microswiss plate mounting.</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Prusa</p> <p...

I created these inner channel clips to keep your Ender 5 plus cables hidden, neat and tidy within the frame. There are two sizes you can use (small & big), it depends on how many cables are in the channel, you'll use the small or big one. Print it...

A customized strain relief for the bed of an Ender 5 Plus. Printed using PLA and optimized with a factory slicer. The requirements are as follows: Two T-nut_M3 (thing:3050607) parts. Two M3 x 20mm Button Head Socket Cap Screws. Two M3 x 12mm...