ender 5 plus electronics case 3d models

I crafted a custom bracket extension from the Hot end bracket after modifying it according to this design: https://www.thingiverse.com/thing:4062242?fbclid=IwAR2Re56JQD-lZ9I2JWj3aP1u1xb2F4TFHnQAuzmyvNhMxiUh5yon3l_Y46Q This bracket attaches to the...

I remixed the previous version which was not centered with the nozzle. I corrected the nozzle relief placement. I then made another version with cooling capability around the entire nozzle using a full circle air duct. I had some issues with the...

This cover allows you to install a 120mm fan on the power supply RSP-500-24

for SKR2

I noticed that the original wire clip design was prone to popping out of the extrusions whenever someone merely touched them by accident. To address this issue, I modified the rounded ends of the clip that fits into the 2020 extrusions and gave them...

Basic screw on X-axis motor strain relief. ... Print horizontal and you'll need M3 screw + nut.

This is a remix, taken from two of Hangtight's designs, the one linked and this one https://www.thingiverse.com/thing:3241793 and modified to fit this bracket for top mounted linear rails: ...

This is spacer for filament sensor to use with dual gear extruder. ...This spacer will align sensor exit with extruder inlet.

pla works good or PETG You will need to buy a spring to go between the backlash top and nut

Simple thing. Prevents the bownden tube from flopping around the filament rinaout sensor after you've moved to direct drive. This is a clip-only design, it pops in place and holds itself from moving up and down using an indent that fits in the...

Blocks are placed along the x-axis rail to ensure it aligns perfectly with the frame. First, loosen the screws holding the wheel carriages in place. Then, adjust each eccentric wheel nut independently on both sides of the carriage until they're...

If the stopper fails during homing, the printhead may slam against the left side of the printer. The first thing to hit is usually the BL-touch, which is particularly fragile. After that, the wheel will likely take the impact against the left side,...

HOW I MAKE IT: <iframe width="560" height="315" src="https://www.youtube.com/embed/RpIH-jXLHm8" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe> MATERIAL: ...

Support for the cable from the bed to the controller.

Donations are accepted via PayPal: gavin@volt3d.co.uk I highly recommend increasing top layer and wall thickness to prevent seeing LED Lights through the part. To fix this issue, I gave my parts 2 coats of white spray paint after printing them with...

<p>Parts Required: (I used Socket Head Cap Screws)<br>qty 6 to 10 - M3 x 6mm screws&nbsp;<br>qty 2 -M5 x 8mm screws and T-nuts<br>qty 2 -M3 x 8mm screws and T-nuts</p><p>You might need to move the bundle holder up a hole to clear the end stop</p>

0.2 layer height supports: yes mounts to back of lcd screen with stock bolts make sure you replace the ground fork

To connect 2 PFTE to sensor. ... Update - now right scale.

This is a custom cable holder designed specifically for E-axis cables. Its sleek and compact design makes it an ideal accessory for any 3D printer setup. Inspired by the innovative design found at Thingiverse, this holder provides a secure and...

wanted to use heat set and also make use of the extra SSR mount holes for more stability. it also moves the board away from the side so you dont have to cut a hole but you also cant access the ports. ... this was ok for me as im running klipper

You will require an M3 screw and a nut to secure the basic screw-on X-axis motor strain relief, which should be printed horizontally.

I enlarged the mounting holes to accommodate an M5 cap head screw.

I got the idea by improving the design of the maker "TwinA"(https://www.thingiverse.com/thing:4011057). I tried to achieve this by reducing the supports and strengthening the fixings. It also showed that the play between the PTFE tube and the...

Designed this small plate to fix the filament runout sensor. The small arm within the sensor misaligns continually when I load new filament. ...Add this to the back of the filament runout sensor to stop this from happening.

<p>I use a Lerdge board on this and wanted to have dual Z axis endstops to keep my bed level.&nbsp;<br><br>You will need:</p><p>2 brackets<br>4 x M2*12mm socket cap or button cap screws</p><p>4 x M2 nuts</p><p>4 x M4*10mm button cap screws</p><p>4 x...

Needed a Gopro mount to do timelape and the original model just saved me loads of time

All brackets mount without the need to drill any holes in anything. Brackets: Back row left to right. X axis carriage bracket: Mounts on the bolts that hold the upper carriage wheels in place. Longer bolts are required: M5 x 40mm. Nylon washers...

I modified these 2 items and remixed it to fit the back rail without needing any additional tools.