ender 5 plus electronics case 3d models

Conclusion : Ventilateur plus grand = plus d'air pour ventilé l'électronique. Attention ! Pour que cela ne gêne pas dans le boitier, il est impératif de prendre un ventilateur de 80x10mm. Modèle utilisé :...

Conclusion : Ventilateur plus grand = plus d'air pour ventilé l'électronique. Attention ! Pour que cela ne gêne pas dans le boitier, il est impératif de prendre un ventilateur de 80x10mm. Modèle utilisé :...

Remixed the Ender 5 End Stop Cover into a Raspberry Pi Camera Case & Mount. I've taken the best elements from various Raspberry Pi Case designs and incorporated them into this one. The result is a ball mount that swivels smoothly. The camera ribbon...

When I ventured into 3D printing, I needed to know the ideal values for perimeter thickness and corner radius when designing cases for electronics. To get a handle on different settings and how layer heights affect print quality and speed, I designed...

It is specifically designed to fit an Ender 5+ with 4020 hotend fan, Micro Swiss hotend, and the ExoSlide gantry upgrade. Not sure if anyone else out there has that setup, same as me, but if not, you might be able to mod my mod for yourself... ...

I needed a custom solution to mount my new BTT TFT35 E3 V3 with WiFi to my Creality Ender 5 printer, so I created this remix based on the original design by michaelvs. ... Hardware Used: 4x M3x8 hex socket CAP head screws for main case mounting 2x M3x16...

... Use hex pattern or triangles infill. Wall line count (perimeter) 5 Concentric bottom and top pattern looks better ;-) I also designed a kind of support for the Stepper, if it gets to hot, to prevent bending in case of too high belt tension.

Hotend and part cooling fan for the MicroSwiss Direct Drive. It is tight in the X direction but you wont loose any build volume, Y is at 46mm not larger than stock. BL-Touch location: X: +8mm Y: -23mm Stuff needed 2x 50x50x15 Fans 6x M3x5 (if you...

I remixed Stians fenomenal creation and removed the piezo-parts, upper place for electronics and cut the left side to not loose X-axis size. It made it a lot more stable in PETG filament. One of the best things is that the belt on X-axis now is...

I made a large 90 degree bracket for the 2020 extrusion. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0,2 Infill: 15 Cubic Filament: CR-3D PLA Gold Category: 3D Printer Parts

Make sure that the rear fans blow into the case, and the front 2 blow out of the power supply and case. After this upgrade I never have had my power supply fan activate. I am using 120x120mm fans from Noctua. ... Note: You need to print 4 stilts so...

Attachment bracket designed specifically for Ender 5 model, engineered for seamless integration onto aluminum frames, ensuring secure and precise positioning of your device.

This saves having load of bolt on on the outside of your printer case and allows for easy cable management that is my next task (don't judge me :p). I might make a re-design of this at some point to include the USB buck converter I have...

https://www.thingiverse.com/thing:586673 My goal was to fit the design on my Ender 3, but I couldn't find a simple solution that would be easy to adapt to various spool sizes and thicknesses available in the market. The design features an 8mm bolt,...

This is a mix of the direct drive mount from paydayxray (https://www.thingiverse.com/thing:4310609) and the hot end side link from Gnizten (https://www.thingiverse.com/thing:4116655) This version has a 9mm Y offset to be compatible with HeroMe Gen 5

I'm installing a custom mount for my TFT35 case (https://www.thingiverse.com/thing:3892049) on my Ender 3, which sits right next to the original screen location. This mount attaches to the same spot as the stock screen mount using identical bolts. ...To...

Spool Holder Parts Required: qty 1 - 3/8" x 5" Bolt qty 1 - 3/8" Nut qty 6 - #6-32 x 1/2" Socket Head Cap Screws qty 2 - 3/8 ID x 7/8 OD x 9/32 width Pre-Lubricated Bearing (I use these because I always have some on hand)...

designed a spool holder that bolts onto the side of the printer via m4 bolts and T nuts. ...than you use a 1 inch diameter dowel for the spools to sit on. note uses drkztan's m4 t nuts. BOL8x M4x12 bolts4x M4x16 bolts12x M4 nuts2'x1" dowel rod

I used self adhesive strip LED lighting on the inside of my e5+ frame and needed to diffuse the light. The clips are offset to clear the Y wheels so they don't get in the way and sit above the bed height, to avoid collision. I would advise 3 clips...

Added some support to keep it from warping so I can use PLA+. tweaked it a little so it lines up with my nozzle better. Been using it for a week now and it looks solid. ...Remember to check "print thin walls" in Cura

I designed this to ensure that there is no pulling and twisting forces on the bowden tube, this ultimately ensures that there is less wear and tear on the bowden tube over time. I got this idea because I saw the bowden tube twisting during...

Lower holder for the heatbed guide rods, so there is more space for a larger hotend and / or fan duct. ... The original screws can be used, 4ea M4 nuts are also required.

3 changes from the original: 1. Remixed to fit the SKR 2 board 2. Combined two formats to allow for mounting the Creality or TH3D Mosfet on the same box 3. ...Added optional zip tie brackets for cable management

A basic table to hold the Sunlu Filament Drier under your print bed and off to the side so you can dry while you print!

This is not a remix of but was directly influenced by this Thing: https://www.thingiverse.com/thing:3836394. The retractable badge holder is an ingenious concept that I wouldn't have come up with on my own. It keeps your cables from sagging and...

SummaryHad issues keeping the hotend cables from catching the printer, so created a tall bracket to keep the cable up. since installing this (with two zip ties), i have not had any issues. Will need supports. ...i used supports with a 3-4% infill for...

<p>Tired of finding the hole you can't see when the bed is in the way? You want this. ...It's not pretty, but it's dead on and works.</p>

This is a remix to have the individual files. Please note the bracket must be mirrored to print the opposite side. ...You will need to support the bracket overhangs.

[Demo](https://youtu.be/RVPKp-yUJQA) ### Info I've tried brass brushes, but they're limited in size (if you use some common brushes available widely) and the melted filament stick too much to the wires so it's hard to remove it. This is a...