ender 5 plus electronics case 3d models

I was tired of having lots of electronics and wires all around the printer, so I designed a enclosure for all of the ender 3 pro electronics including a raspberry pi. I wanted to have the front of the printer full of drawers for tools and parts so...

Key features include internal mounting points specifically tailored for a Duet 2 board, leaving ample room for customizing with additional electronics as desired. ... An external opening allows for easy installation of a 40mm fan, while strategically...

Mounted similar to original 2-hole version with using 4 holes instead:

All the electronics boards are secured with PC case screws, and the sides and fan with zip ties. I put some holes in the Raspberry Pi side so I could mount to the extrusion if I wanted to. I also filleted the mounting risers since I've experienced...

This is a replacement cover for the stock electronics cover for the Creality Ender 3. It features new cable cutouts to allow the PCB enclosure for the TH3D EZ-ABL sensor to mount on top of the extrusion next to the box, and lets all of the cables to...

Boxing for Electronics on Anycubic Delta Plus fan 7015 Крышка из оргстекла

I imported Usuariu's electronics box into Tinkercad and rotated it so that the card reader was positioned at the back, then added some holes and reinforcement to the new front for the display. I sealed up the old wire opening and included a side hole...

... are available; I suspect I have some over-extrusion going on. To join the two cases, I had to do some grinding. The lids are extremely tight. It seems I'll need to print a straight bed chain connector as it looks slightly bent. ... Have Fun

... I thing I have some Over Extrude going on. I had some grinding to do to make the 2 cases join and the lids are verrry tide. I guess I have to make/print a straight bed chain connector too it looks a bit bend. ...Have Fun Category: 3D Printer Parts

This is an electronics cover/screen cover for my Ender 3 Pro, which also fits the Ender 3 perfectly. It's designed to be installed easily using the existing screws and the tools that come with your printer. Additionally, a plug is included to cover...

PC case screws secure all electronics boards, while zip ties hold the sides and fan in place. I drilled holes into the Raspberry Pi side to enable mounting on the extrusion if needed. Additionally, I filleted the mounting risers to prevent them from...

I can add bottom plate if needed/required Uses a variety of Manets and slide in T-slot adapters to add strength to the build Free Files associated to the file: Voron Parts:...

......Each of the 4 sides holds each of the electronic components. All the electronics boards are secured with PC case screws, and the sides and fan with zip ties. I put some holes in the Raspberry Pi side so I could mount to the extrusion if I wanted to.

... secure place to reside. ...I created a custom base and attached it firmly to the underside of my worktable using a strong gorilla adhesive. To prevent accidental removal of the sensitive electronics, I added stabilizing supports beneath the small stop.

I made a 90 degree bracket for the 2020 extrusion for the Ender 5 Plus

Ender 5 Plus filament runout sensor spacer for dual gear extruder (Redrex) upgrade

https://github.com/BladeScraper-Designs/Ender-3-All-in-One-Enclosure The Ender 3 Pro version of this enclosure has ceased development, but it remains available here on Thingiverse. It is still fully functional, but may lack some of the latest design...

These prints are specifically designed to be used with an enclosure, allowing you to relocate all electronics and power supplies underneath it. To mount components, use 1/2 inch MDF; alternatively, you can attach them directly to the top of a Lack...

Support for the electronics of the Anycubic Kossel Linear Plus is a must-have component for optimal performance. ...We highly recommend printing the fan support as well, which will ensure effective cooling of the electronic components.

To provide extra cooling, I made a mount for a 24v 120mm fan that's plug-and-play with stock Ender 3 mainboards, requiring no soldering. This is also linked below, along with plenty of air ventilation holes on the sides and back. My design uses all...

Tinkercad friendly.This will fit any ender 3 stock mother board pattern motherboard and is currently configured for a massive 92mm cooling fan. Assembly is still the same. The enclosure lid slides via rails into the enclosure body with the...

I really liked the original, but I wanted a front case, due to not having space in the rear, and wanting to maintain access to the SD card slot. This is set up for an SKR 1.4/1.4 Turbo board and a 30mm fan on the left, and a Pi, buck converter and...

I really liked the original, but I wanted a front case, due to not having space in the rear, and wanting to maintain access to the SD card slot. This is set up for an SKR 1.4/1.4 Turbo board and a 30mm fan on the left, and a Pi, buck converter...

Made this to mount 7" Pi screen to my Ender 5 Plus.Should work in any extrusion with adequate space.Made for use with Pi Screen Case https://www.printables.com/model/237957-raspberry-pi-7-touch-screen-display-lcd-tft-case-e4x M3 bolts4x M4 bolts4x M4...

Purpose: - Very Simple Adapter for Fitting the Meanwell RSP-500-24 into the Ender 5 Plus Case - Included Blanking Plate for Voltage Selector Notes: - 4x M4x4mm Button Head Bolts for Case Fixing - 4x M5x5mm Countersunk Hex Bolts for PSU Fixing -...

Purpose: - Very Simple Adapter for Fitting the Meanwell RSP-500-24 into the Ender 5 Plus Case - Included Blanking Plate for Voltage Selector Notes: - 4x M4x4mm Button Head Bolts for Case Fixing - 4x M5x5mm Countersunk Hex Bolts for PSU Fixing -...

This is a board mount for the large ender 5 Plus case for the BTT SKR 1.4 or SKR 2.0 mainboard + the BTT UPS board. Slot fit over existing mount holes and use existing screws. ... Please see updated version to include Raspberry Pi: -...

This will be fixed in an future version.Edit (3.5.2024 Hotfix!) :Due to some weird measurements, the adapter didn't fit, because of the screws of the mounting plate of the Ender 5 Plus.Edit (2.5.2024) :Unfortunately, I had a very busy time last...

CREALITY ENDER 5 PLUS SPOOL HOLDER CENTERED BRACKET EASY TO PRINT As my Ender 5 Plus arrived, I found the spool holder fixing needed improvement. You may also notice that I've used my "Creality Ender 3 5 Pro Plus Universal Ball Bearing Super Easy...

Nothing special, I printed using Standard PLA on cool plate.