ender 5 plus electronics case 3d models

This is a remix of the Ender 3 Z-axis endstop to use on the Ender 5-plus. The area that holds the endstop board is basically the same, but enlarged and reshaped slightly to fit the endstop boards I have. It was also changed to use M3 heat set...

The jetpack has been halved and will fit on an Ender 5 Plus bed and print without supports. To put the halves together I have added dowels and pocket screws. I've also put in some screw holes at the back and adapted the way the rockets are fitted so...

I wanted an LED strip light for my Ender 5 Plus, but all I found was this one for the standard Ender 5: https://www.thingiverse.com/thing:4125317 Front and rear lighting is nice, but it wasn't wide enough for the Plus so I needed something bigger. ...

... of the bed is necessary to ensure adequate printing height, given the adjustment to the 8mm rod brackets. Following these modifications, the risk of collisions is eliminated, allowing seamless integration with the original Ender 5 Plus firmware.

I used the E3D Volcano mount to attach the Spider to the Ender 5 Plus. This allows you to position the Spider at the same z height as the stock hotend. You mount it upside down from the pics in the link: ...

You may think that it's not Ender 5+ any more, but almost everything from the original kit is reused with minimal adjustments.That was the design intention:- no hassle with electronics: 100% ender5+- sturdy frame: I use locally available "Kombi...

VIDEO: https://www.youtube.com/watch?v=RpIH-jXLHm8 ENDER 5 PLUS: https://bit.ly/2YHzpws BMG: clon:...

---------------------------------------------- This is an adaptation of my unpublished Ender 5 Duet Mount, modified for the Ender 5 Plus. It utilizes a 40mm fan (recommended: 24v SUNON 4020 or 12v Noctua 4020 via a buck converter) to direct air...

This mount allows to use the stock extruder of the Ender 5 Plus to be used as direct drive extruder. Installation: 1.) Unscrew the fan chassis, the BL-Touch sensor as well as the hotend 2.) Disassemble the upper two mounting wheels of the...

Hello all, Here's an ajustable webCam support for Ender 5 plus ... or for all printers that has 2020 profil All the parts can be printed without support except for part 7. All the parts are printed mostly on the side edge so that the holes are...

A light bar for the Ender 5 + may fit the Ender 5 pro. Wide enough to hold normal LED's or the Neopixels. ... Wire holders on both sides so you can hold the cable.

Remix of Ender 3 - Filament Holder Deluxe (https://www.thingiverse.com/thing:3114139) for Ender 5 Plus (tried to upload it as remix, but Thingiverse is not able to find the original design) - I was happy with the original design that I have used on...

Not sure where the original design came from but I have it on my ender 5. Bought a 5 plus and wanted to add similar protection to the BL touch. ...Quickly discovered that I needed to add a few mm to it in order to maintain the clearance of the rail...

This is a Ball-Bearing Filament holder for Creality Ender 5 Plus (or possibly other models) designed to accommodate filaments weighing 1000g or less with an inner diameter of 52mm. To complete this project, you will need two sealed ball bearings...

One was for Ender3 and the other was a rough Ender 5 Plus design that needed jesus. This should be usable with the Ender5+ with little to no modifications to your printer. It uses the default hardware. BLTouch mount is about 5mm to the left of the...

When you get your aliexpress linear rails for your Ender 5 plus, you might get install blocks as pictured, luckily I did. Those install blocks are inadequate since they end up putting the X gantry far too high on the top 4020 channel. Drop the rails...

Simple yet effective replacement for your Ender 5 Plus duct fan. Exhaust is directed under a small angle, now featuring rails, so airflow points directly at the nozzle tip. I hope you'll be satisfied with the results. If any issues or tips arise,...

Since uploading my Ender 5 Plus Micro Swiss cable support bracket, I have redesigned a bracket to fit at the end of the X Gantry to mount the cable on to support it away from the metal frame and the wheels on the gantry. You will need to install...

This is a housing for the Mini 12864 LCD display to fit inside the Ender 5 Plus chassis without modifications.It bolts on from inside using the original mounting points and screws.You mount the LCD to the back cover first with the M4 screws and nuts,...

...My design has been put to the test on my Ender 5 Plus printer, which operates seamlessly without any hardware holding it back. To accommodate varying bed thicknesses, users can fine-tune their designs using the scale feature in the slicer software.

Aluminum LED Channel brackets for the Ender 5/ Plus printers. You will need to print two of each file for all four needed. The brackets do not have holes for the wiring, but 10 seconds and a drill bit will put the hole wherever you want it. ...

This is a filament lead in tube (Bowden) end holder for Ender 5 Plus direct extrusion modifications. It is designed to hold the end of the filament lead in tube from the filament break detector to the direct extruder. The filament bracket installs in...

This piece supports the wire going to the hot end on the Creality Ender 5 Plus. The V4 file is designed to connect to the printer with two M3x10 machine screws and two M3 T-nuts, while the tube connects with a zip tie or twist tie. This piece...

I encountered a problem with my Ender 5 Plus in that the front was lower than the back even when everything else was equal. This led to rear adjustments being significantly tighter than the front and became an issue when I switched to solid silicon...

I created a mounting bracket for the BigTreeTech PiTFT50 screen to fit on an Ender 5 Plus. The design is in 2 parts (plus the retaining clips). Because of the way it's designed, you can still mount the Pi on the back of the display if you wish.</p>...

If your printer uses the same carriage plate that the ender 5 plus does then this should work for you too. This uses the stock BLtouch mount and you can use the stock 40mm fan but if you want the cooling fan you'll need a 5015 blower (I have not done...

My take on the low friction spool holder designed to fit the Ender 5 Plus bracket. It ended up being too low friction and would spin on its own. ...I added some foam between the spacer and the spindle body, which resolved the issue. Required Hardware:...

Decided to go another route, but if I had kept it I would've reprinted in PETG.Printed great on my Ender 5 Plus, I added 3 perimeters(for a total of 6) and 10% infill(for a total of 25%) for some added strength.Print SettingsPrinter...

I created a mounting bracket for the BigTreeTech PiTFT50 screen to fit on an Ender 5 Plus. The design is in 2 parts (plus the retaining clips). Because of the way it's designed, you can still mount the Pi on the back of the display if you wish. ...

---------------------------------------------------- This is my design for a kinematic self levelling bed system for the Ender 5 plus. This design allows you to fully automate the levelling of your bed to a very high precision - meaning you only...