ender 5 plus dimensions 3d models

The Linear Rail Brackets from Ralp57 (https://www.thingiverse.com/thing:4487342) suggest what I felt was an unnecessarily complicated way to raise the Z screw and Z linear Rails. You need to raise the bed when fitting linear rails because the X...

pla works good or PETG You will need to buy a spring to go between the backlash top and nut

Plugs directly into an unused SD card slot found on a standard 12864 case design, similar to one described by TH3D in their 12864 conversion setup.

wanted to use heat set and also make use of the extra SSR mount holes for more stability. it also moves the board away from the side so you dont have to cut a hole but you also cant access the ports. ... this was ok for me as im running klipper

This is a remix of: https://www.thingiverse.com/thing:3842765, but it woudn't find it when I checked remix... This adds the option to use the front mounting holes to secure the screen enclosure. I also added a large lip to the back underside with the...

I remixed the Bed Rod Holder to allow attachment from the bottom of the extrusion, instead of the side. This allows for additional clearance for a left mounted probe on a long hotend like a volcano. ... I now only need 2.5mm of clearance to avoid...

Look how close that X-axis Stepper Motor wire comes to the rollers. ... Move that wire away from the rollers with this!

This is a remake of https://www.thingiverse.com/thing:4091776 The mounting bracket did not fit my needs, so i used the cooling fangs from the original thing, and made a new mounting bracket, fitting my Kay CoreXY convertion. Printed with tree...

A human requires an additional module to be installed.

Support for the cable from the bed to the controller.

This is a like the clips that come with the Printer. Only you can make more of them. ... Lots more!

Uses the stock mounting points and converts them for a BTT Manta M5P Board. Also moves the Bed Mosfet down out of the way. ...Fusion 360 file included for remixing, please link if you do.

just a quick remix sorry for poor skills hahaha

Touch Sensor Protection System: Preventing Catastrophic Failure We designed this system specifically to safeguard the BL touch sensor. Its primary function is to protect against X-axis runaway, a potential cause of sensor damage. By implementing...

Hay just wanted to share the First thing ive made :) This is a No Bolts Clip on spool arm holder made to work with "Filler - The Customizable Filament Holder" (https://www.thingiverse.com/thing:3020026) it is also maded to move your spool...

This is a remix to have the individual files. Please note the bracket must be mirrored to print the opposite side. ...You will need to support the bracket overhangs.

This is included in the Files. All parts print in the given orientation with NO supports or brims. I recommend you print the parts in PetG. I used M5x12mm bolts to replace the grub screws in the 60t pulleys for better grip. Lightly sand...

3 changes from the original: 1. Remixed to fit the SKR 2 board 2. Combined two formats to allow for mounting the Creality or TH3D Mosfet on the same box 3. ...Added optional zip tie brackets for cable management

A basic table to hold the Sunlu Filament Drier under your print bed and off to the side so you can dry while you print!

The Linear Rail Brackets from Ralp57 (https://www.thingiverse.com/thing:4487342) suggest what I felt was an unnecessarily complicated way to raise the Z screw and Z linear Rails. You need to raise the bed when fitting linear rails because the X...

This is a mounting plate to put the BTT TFT70 on the lower right front corner of the machine. I got fed up with not having a place to put it, so this solves my issue. I printed in PLA for the draft that you see in the photo, but you may want to...

This is a remix, taken from two of Hangtight's designs, the one linked and this one https://www.thingiverse.com/thing:3241793 and modified to fit this bracket for top mounted linear rails: ...

Mounting is the Same as my other h2 mount https://www.thingiverse.com/thing:4889163 Nozzle to Probe -33,-11, Z should be same as stock mounts using 2 M3 x 8mm botls for the H2 and 2 M3x 8mm bolts (may want use a washer) and 2 m3 nuts for the Bl...

This tip might prove beneficial for iPhone case creators.

https://www.thingiverse.com/thing:4441076

A simple tool holder to hold the wrenches, hex wrenches, scraper, cutter, and screwdriver that come with the printer Mounting requires: - 2x M4x10mm or M4x12mm bolts - 2x M4 T-Nuts - M5 will also work, but you will need to expand the...

https://www.thingiverse.com/thing:4441076

I have crafted a precise 3D Solid model of the iPad Pro (10.5-inch) based on official Apple blueprints, ensuring accuracy to original dimensions. This CAD model is available in various formats. Additionally, I offer a range of high-quality 3D models...

Simplified Ender Model 5 Created as Chamber Design Base I designed it specifically for chamber design applications and made sure to include all key dimensions with an accuracy of 1mm. Perhaps someone can utilize these specifications. To access the...