ender 5 plus dimensions 3d models

Frustrated with cords constantly jamming into the limit switch and disrupting your printer? This is the answer. ... Design by: 3D PAT CA

This is a modified Version of the aftab's cable chain tray: https://www.thingiverse.com/thing:4164988 enjoy it :-)

This is a dragchain i made for my Kay CoreXY setup, with a Hemera hotend and BL touch. This setup have been tested and for those who have downloaded earlier versions, there have been some adjustements. The BL_touch is now relocated to make a...

I modified these 2 items and remixed it to fit the back rail without needing any additional tools.

You will require an M3 screw and a nut to secure the basic screw-on X-axis motor strain relief, which should be printed horizontally.

Customized version of https://www.thingiverse.com/thing:3507663 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3507663

Made a split version SO I didnt have to disengage the motor etc. Debranded . ...

Donations are accepted via PayPal: gavin@volt3d.co.uk I highly recommend increasing top layer and wall thickness to prevent seeing LED Lights through the part. To fix this issue, I gave my parts 2 coats of white spray paint after printing them with...

<p>Parts Required: (I used Socket Head Cap Screws)<br>qty 6 to 10 - M3 x 6mm screws&nbsp;<br>qty 2 -M5 x 8mm screws and T-nuts<br>qty 2 -M3 x 8mm screws and T-nuts</p><p>You might need to move the bundle holder up a hole to clear the end stop</p>

Relocates the Y axis stop sensor to the back rail to allow for horizontal movement for exoslide plates

I made an error in the BLTouch bracket height. If you have already printed V1, my apologies for the wasted time and filament. A few mods; all of the hard work had already been done: - I raised the filament sensor so as to clear the Hemera...

I crafted a custom bracket extension from the Hot end bracket after modifying it according to this design: https://www.thingiverse.com/thing:4062242?fbclid=IwAR2Re56JQD-lZ9I2JWj3aP1u1xb2F4TFHnQAuzmyvNhMxiUh5yon3l_Y46Q This bracket attaches to the...

I remixed the Microswiss X_Carriage with 3 screwing positions for an inproved grip. On the right the M3 hole must be drilled to 4,2mm. ...The hole on the bottom must also be drilled (I was not able to edit it right...) It's my first time I was able...

Fixed the error where the wall disappear

My printer is enclosed by affixing plexiglass to the frame and has a removable cover over the top. I wanted to heat up the chamber so I came up with this solution. I bought the heater from amazon. it is a generic heater and does not have a...

First one you can use your stock bltouch bracket. Use ABS or PETG. 30+% infill. Use this duct with it. ... https://www.thingiverse.com/thing:5340802

# I'll be updating this shortly with the parts list and more details # ### Why? ### This started because I wanted to use the Bondtech extruder as direct drive with a v6 as it was intended. This was before the release or talk about the Micro Swiss...

I installed a Duet wifi and didn't get a screen and after using it I realized I haven't run into a time where I felt I needed it. I have mounted the control box on the back pointing upwards, the hole in the center is for the wires going to the...

If the stopper fails during homing, the printhead may slam against the left side of the printer. The first thing to hit is usually the BL-touch, which is particularly fragile. After that, the wheel will likely take the impact against the left side,...

I enlarged the mounting holes to accommodate an M5 cap head screw.

Customized version of https://www.thingiverse.com/thing:3507663 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3507663

Clamp on rings using 3mm x 8mm long screws to give a homing reference to z motor position in case one side z is moved out of sync to the other. You set the z bed frames to same distance from top of frame down. ...Then auto home.The pointer is then...

He creado esta pieza para ayudar a recoger los cables aquellos que utilicen Hero Me Gen4 Dual 5015 Cooling System https://www.thingiverse.com/thing:4523667 Junto con Extrusión directa. ... Impreso en PLA

To connect 2 PFTE to sensor. ... Update - now right scale.

Mounting plate adapter to use microswiss direct drive plate with the exoslide system To mount remove exoslide, mount plate to exoslide then mount plate to microswiss plate then mount exoslide back on rail

This is an idea I had to use as much stock Crealty hardware (which works great with an all metal heatbreak). The idea is to make a mount for dual 5015 fans for blowing across the stock Creality MK8 heaterblock. An airdam at the bottom to block off...

SummaryHad issues keeping the hotend cables from catching the printer, so created a tall bracket to keep the cable up. since installing this (with two zip ties), i have not had any issues. Will need supports. ...i used supports with a 3-4% infill for...

Changed the Desgin a bit because i had the problem that my modded fan duct hit the thing while leveling.

BTT TFT35SPI Mount. ...Added optional feet if you want to mout the pit to it