ender 5 plus dimensions 3d models

All brackets mount without the need to drill any holes in anything. Brackets: Back row left to right. X axis carriage bracket: Mounts on the bolts that hold the upper carriage wheels in place. Longer bolts are required: M5 x 40mm. Nylon washers...

<p>The shorter the bowden tube, the better, right?</p><p>This mod allowed me to shorten the Tube by 17cm to 43cm. But measure yourself, as it is depending on your hotend and extruder.&nbsp;</p><p>The arm also damps the vibrations of the extruder...

Lower holder for the heatbed guide rods, so there is more space for a larger hotend and / or fan duct. ... The original screws can be used, 4ea M4 nuts are also required.

I used self adhesive strip LED lighting on the inside of my e5+ frame and needed to diffuse the light. The clips are offset to clear the Y wheels so they don't get in the way and sit above the bed height, to avoid collision. I would advise 3 clips...

Designed this small plate to fix the filament runout sensor. The small arm within the sensor misaligns continually when I load new filament. ...Add this to the back of the filament runout sensor to stop this from happening.

I designed this case to move the Original screen outside the enclosure to make room for an SKR E3 Turbo mainboard. ...I used on the inside a mount from Thingiverse https://www.thingiverse.com/thing:4676133

Shortened version of https://www.thingiverse.com/thing:3020026 (can't get it to link!) Made so it can still sit on the inside of the frame as I have a wall behind. ... Adjusted to print on side with minimal support.

This is a remix to mount a 12864 type B display (has jog dial on the side) to the E5+ without cutting the case. I needed this when I switched my printer to Klipper and did not want to mess with 12864 emulators on other displays. Materials needed: ...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

<p>I use a Lerdge board on this and wanted to have dual Z axis endstops to keep my bed level.&nbsp;<br><br>You will need:</p><p>2 brackets<br>4 x M2*12mm socket cap or button cap screws</p><p>4 x M2 nuts</p><p>4 x M4*10mm button cap screws</p><p>4 x...

This is a custom cable holder designed specifically for E-axis cables. Its sleek and compact design makes it an ideal accessory for any 3D printer setup. Inspired by the innovative design found at Thingiverse, this holder provides a secure and...

I prefer straightforward solutions that don't require any specialized equipment or modifications. This design fits snugly in place without needing anything removed, making it easy to implement. Since every printer is unique, you can use a small piece...

Added some support to keep it from warping so I can use PLA+. tweaked it a little so it lines up with my nozzle better. Been using it for a week now and it looks solid. ...Remember to check "print thin walls" in Cura

for SKR2

I made it almost 1 to 1 with small changes. it works since the replacement perfectly. ... Be sure to print it with 4 lines for the wall and 50% infill for a longer lifetime.

This cover allows you to install a 120mm fan on the power supply RSP-500-24

My version of the bed raise. I use 100mm M4 screws, as well as additional springs about 20mm (0.75in) in outer diameter. If you use springs which have been flattened you probably won't need the spring keepers. I remixed the motor side riser to...

[Demo](https://youtu.be/RVPKp-yUJQA) ### Info I've tried brass brushes, but they're limited in size (if you use some common brushes available widely) and the melted filament stick too much to the wires so it's hard to remove it. This is a...

Designed to support the heat bed cables to help take some of the strain from the solder joints of the cables when bed is at the high positions. Undo the 4 pcs m4 screws holding the linear guide bearing, slide it between the guide bearing and...

I liked this design, but wanted to use it with an E3D Volcano and an EZABL Pro. The Volcano will mount directly to the BMG. I also moved the location of the hotend fan to be higher. I added an EZABL mount to the left side.Lastly, I cut away the...

This is spacer for filament sensor to use with dual gear extruder. ...This spacer will align sensor exit with extruder inlet.

HOW I MAKE IT: <iframe width="560" height="315" src="https://www.youtube.com/embed/RpIH-jXLHm8" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe> MATERIAL: ...

Remixed to be able to print in two pieces and glued or bolted together. ...Second mount added on the front panel for another 40mm fan.

Wanted to put my BigTreeTech SKR 2 board in the middle of the open space to have access to all sides of the inputs, including the USB port for a Raspberry Pi running Klipper, but Kersey Fabrication's mount pressed the inputs up against the case, so...

I remixed the previous version which was not centered with the nozzle. I corrected the nozzle relief placement. I then made another version with cooling capability around the entire nozzle using a full circle air duct. I had some issues with the...

This is not a remix of but was directly influenced by this Thing: https://www.thingiverse.com/thing:3836394. The retractable badge holder is an ingenious concept that I wouldn't have come up with on my own. It keeps your cables from sagging and...

I've adapted the style of belt tensioners on my Y-axis by shortening the inner arms, allowing them to press firmly against the front horizontal extrusion. Having successfully implemented this modification, I was pleased with the outcome. However,...

Hi, hier findet ihr ein Case für das BTT TFT35 V3. Es wird aufgesetzt, so das SD und USB verfügbar sind. Benötigt werden 8 x Ruthex M3 Muttern -...

I designed this to ensure that there is no pulling and twisting forces on the bowden tube, this ultimately ensures that there is less wear and tear on the bowden tube over time. I got this idea because I saw the bowden tube twisting during...