ender 5 plus dimensions 3d models

I dident like the fact that the filament was behind the printer, but i did want the printer in a corner. loading and unloading was a problem and if the bed was in a wrong  position the spool was stuck. ... so i moved the spool holder and made this...

I no longer use the stock screen due to me running klipper and using a 7 inch screen. I needed extra cooling for my Manta M8P and this does the trick just fine. I can run 1.6 amps on my steppers without overheating. Attached is F3D and STL. ...I used...

The design has been revamped to securely clip onto the bar without requiring users to disassemble it first. Instead, the new version is optimized for seamless installation by attaching directly onto the bar. ... Remixed: The original model was...

Requires four M3 nuts (1 per wheel)

HOW I MAKE IT:SPOOL HOLDER: https://www.thingiverse.com/thing:4765789PLA: https://bit.ly/3svAHrbFOLLOW ME:Youtube: dukedoksInstagram: @dukedoksFacebook: @dukedoksSOFTWARE:Fusion 360

Replacement legs for my Vizio E50-E3. I do not have original part, so I made it using caliper and photos from internet. vizio_e50_left_leg.stl and vizio_e50_right_leg.stl - full size models vizio_e50_left_leg1.stl +vizio_e50_left_leg2.stl =...

I use a combination of Octoprint and a webcam to monitor my printings. To get a better view of the printer I designed a simple Webcam Bar to mount the webcam on. Parts you need beside the printed part: 1x T-Nut M4 1x Nut M4 2x Bolt M4x12 ...

This is a camera mount for the Creality camera or any camera that uses a 1/4" bolt. You will need 2 m3x10 screw and 2 m3 t slot nuts. It has worked great on my print. Set the x axis to 100mm if it does not size correctly. ...and when printing have the...

HOW I MAKE IT: <iframe width="560" height="315" src="https://www.youtube.com/embed/RpIH-jXLHm8" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe> SPOOL...

just a simple screen cover with a biohazard emblem

Uses a single m3 screw. ... Print with no supports.

Dual 5015 fan remix. ...

Print this with carbon fiber nylon with 100% infill. ... Set the z seam at a user specified point and choose expose seam if you want to keep the bolt holes clear.(see photo) HotEnds are here ...

I switched to a BTT manta m8p and moved all my electronics out of the big metal case and needed a new place for my mosfet. ... 4 X m3x4mm for mosfet 2 X m4x8mm /w t-nuts for extrusion mount

I liked how this duct was laid out, but I also like to be able to see the hot end clearly while printing. So I've rotated the duct to the back of the assembly, made room for the lower roller and added some internal vanes so you don't need to use...

This design raises the filament sensor if you change your extruder to a dual gear extruder Required 4x M3x25 Socket Head

<p>Simpel improved fan duct, exchange with standard one.</p> <p>Print without supports in vertical position</p> Category: 3D Printer Parts

I found that the original design had two very slight protrusions on the bottom surface preventing it from printing properly for me. I flattened the bottom. Still printing so we'll see if it fits! ... One version with and one without bltouch bracket

Just extended the brackets from the original to close up the gap in between the brackets and widened the acrylic grooves

this part secures round the original filament holder using the original screws and two m3 nuts this help for anyone with a direct drive setup and using for long prints

You can purchase a 48-LED aluminium LED strip with switch at Jaycar. The holder for this light fixture has one minor installation problem - it requires snapping off one tab and reattaching it with glue. ...Despite this issue, the product functions...

Modified components created by me for use with the Raspberry Pi Camera, which is designed to work seamlessly with OctoPi.

blind plate for the E compartment if you use a RPI with klipperscreen

Prevent Cable Breakage with Ease! ...Simply Snap on a Ziptight and Go!

I noticed that after a while the version FanDuctEnder5-2_v7 is losing its shape due to the heat of the hot end. I added a new design: FanDuctEnder5-4_V19. This new design has more space around the nozzle. Airflow will be less concentrated, but the...

Simple bump stop to add mount on the front left top bar on the printer to stop the head from ramming the front (and the nozzle to possibly scrape on the lip of the build plate) if Y homing didn't go all the way to the bump stop.