ender 5 plus case 3d models

I wanted to mount a Voron M4 Extruder to my Ender 5 Plus while retaining the stock filament runout detector so I designed this piece to mount it much like the stock extruder. ... You will need 4 M3 screws and nuts to mount the runout sensor, 3 M5...

hello this is my modded led light bar holder for my ender 5 plus but will fit others on the main bracket i used 50% infill and on the led holder i used 100% infill this is to fit the led which was from amazon this is the link...

I'm using it on my ender 5 plus inside the enclosure to monitor both temp and humidity in there. It mounts with 2 m5 screws and a couple Tnuts. Step file included for those of you that need or want to modify it. ... Be sure to use support when...

This is actually inspired by WyvernPL's fan duct for the Ender 5 Plus. I aditonally made a adapter part to replace the PSU fan with and put the fan grill inside the housing so it is completely flat on the ouside. The tube is raised at the larger end...

I designed a low friction spool holder to fit the Ender 5 Plus bracket, and it turned out to be too slick. The spool would spin freely on its own without any assistance. To correct this issue, I inserted some packing foam between the spacer and the...

I wanted a sleek light bar for my Ender 5 Plus, but every standard LED strip didn't fit, so I grabbed xqqqqme's clips and gave them a makeover to match LilTrublMakr's bar perfectly. I removed the v-slot modification and here's what I came up with -...

I wanted to mount a Voron M4 extruder to my Ender 5 Plus while retaining the stock filament runout detector so I designed this piece to mount it much like the stock extruder. ... You will need 4 M3 screws and nuts to mount the runout sensor, 3 M5 screws...

The official Creality all-metal extruder upgrade (Pictured) sits slightly wider than the standard plastic Ender 5 Plus extruder, causing the filament exiting from the filament runout sensor to misalign with the new metal extruder. I created a...

Bretware Ender 5 PLUS Chain System Please subscribe to our Youtube channel https://www.youtube.com/channel/UC-dZpDgCGSf7w-vZWgO2Nsg/videos Uses Johnniewhiskey Ender 3 chain To be used with the following, Chain and covers...

Dan's tutorial and parts can be found here: https://e3d-online.dozuki.com/Guide/Hemera+Creality+Ender+3+(CR-10)+Upgrade./107?lang=en For my Hemera conversion, I utilized the stock Ender 5 Plus Thermistor, Heater, and Fans and purchased a longer...

I wanted an LED strip light for my Ender 5 Plus, but all I found was this one for the standard Ender 5: https://www.thingiverse.com/thing:4125317 Front and rear lighting is nice, but it wasn't wide enough for the Plus so I needed something bigger. At...

Key Features: * Complete protection from dust, dirt, and other debris * Simple snap-on design for easy installation * Reduces noise levels emitted by the printer * Durable 3D printed construction * Perfect for Ender-5 Plus owners who want to get the...

You may locate the crossbar at any height you find suitable for your setup.Also consider printing the End Covers that protects you from the sharp edges that get exposed when you relocate the crossbar:...

Made this for ender 5 plus to attach cable chain to extruder in a direct drive setup. I could not find anything with key words to find something. So I made it. This is just the brackets to mount cable chain from...

I am currently working on turning my Ender 5 Plus into a high temp filament machine. In that endeavour I realized that I would have to move all my electronics outside the main body so that I can use 1/8" acrylic in the frame as an enclosure. So I...

This is to mount a Duet 2 Wifi and paneldue in an Ender 5 plus positioned in a way to get maximum Wifi signal. ...you will need to move the mosfet to do this mod, use: https://www.thingiverse.com/thing:4888746 The screen cover and mount is found here:...

This spacer is specifically designed for users who have installed the BondTech BMG extruder on their Creality Ender 5 plus and still want to utilize the filament run-out sensor. *Update* I initially provided an incorrect spacer, which I promptly...

Not sure where the original design came from but I have it on my ender 5. Bought a 5 plus and wanted to add similar protection to the BL touch. Quickly discovered that I needed to add a few mm to it in order to maintain the clearance of the rail...

Gehäuse für das Bigtreetech TFT70 v3 um es an den Ender 5 Plus zu verwenden. Die Bodenplatte habe ich mit 5 Magneten 1x8mm die in die Aussparungen eingeklebt werden befestigt, somit kann man sie jederzeit abnehmen. Man Kann Sie aber auch mit...

I've been struggling to prevent the hotend cables on my Ender 5 Plus from getting tangled up in the printer, so I came up with a clever solution: designing a sturdy bracket that keeps the cable elevated out of harm's way. Since installing this...

A customized strain relief for the bed of an Ender 5 Plus. Printed using PLA and optimized with a factory slicer. The requirements are as follows: Two T-nut_M3 (thing:3050607) parts. Two M3 x 20mm Button Head Socket Cap Screws. Two M3 x 12mm...

I created these inner channel clips to keep your Ender 5 plus cables hidden, neat and tidy within the frame. There are two sizes you can use (small & big), it depends on how many cables are in the channel, you'll use the small or big one. Print it...

A custom strain relief for the Ender 5 Plus extruder, crafted with precision using PLA and optimized settings from the factory slicer. To bring this design to life, you will need: 1. An M3 x 12mm Button Head Socket Cap Screw 2. A set of M3 Flat...

This is a top mount filament spool holder remix specifically for the Ender 5 Plus. The original from Les73gtx is: https://www.thingiverse.com/thing:4536704 I made this one taller and added an angle at the same time in order to move the spool...

Bolts to the side of the bottom 2020 extrusion on the Ender 5 Plus. My printer is enclosed on the sides so the 3mm tube that comes with the dryer loops around, goes through a hole in the side and feeds into a filament guide arm which then feeds up...

This is a housing for the Mini 12864 LCD display to fit inside the Ender 5 Plus chassis without modifications.It bolts on from inside using the original mounting points and screws.You mount the LCD to the back cover first with the M4 screws and nuts,...

I got tired of trying to get the whole bed carriage level on my Ender 5 Plus. It tends to sag a little when the power is off, and I struggled to get it back to level every time I powered it on. This simple solution fits on top of the bed frame and...

Tube guide for the Creality Ender 5 Plus to avoid contact with the drive axis. The tube with the wiring for the hot end slides between the drive axis and the frame. The part is mounted on the rail with two T-nuts and M5x12 screws. The tube can be...

A simple tool for you to align the dual z axis on your Ender 5 Plus. Print 4 of these and place on the smooth rods. You can print the block in solid or without top and bottom. If you only have 1 stepper driver for dual Z and cannot preform Marlin...

Extended version of trays to fit the Ender 5 Plus Original parts still required from: https://www.thingiverse.com/thing:4116655 Changes: X-Axis screw holes reduced for M3 screws X-Axis Right, modified to fit around endstop, so no need to change....