ender 5 plus case 3d models

Housing for an Ender 5 Plus. Printed components were made in NiceABS, and the following are still needed: Acrylic sheets: 2 pieces, each measuring 555x400x3mm; 2 pieces, each measuring 510x420x3mm; 2 pieces, each measuring 637x200x3mm; 2 pieces,...

Modified based on https://www.thingiverse.com/thing:4795205 for the Ender-5 Plus * Changes some of the screw points * Moved one of them to allow for a Ground Wire * Added clamp system for the Ender-5 Plus control box All credit goes to the original...

This is a bracket for the Ender 5 Plus controller case to move the cooling fan from the bottom to the rear of the controller case and cover the fan's old hole. The air will now be pulled in the front sides and exhausted out the back. The bracket can...

That plus an SKR for the steppers, and I won't lose quite as much hearing before going back to my office in the year 2025 maybe? Printing: I meant to do the bottom and middle in ABS, but I did the top in ASA. When I printed the bottom, I used ASA,...

I switched to a BTT manta m8p and moved all my electronics out of the big metal case and needed a new place for my mosfet. ... 4 X m3x4mm for mosfet 2 X m4x8mm /w t-nuts for extrusion mount

A replacement case cover for the Ender 5 Plus, allowing you to mount two Noctua 92mm fans to keep the system cool, and quiet. The main reason I did this was to prevent the power supply fan from turning on, as it's louder than most commercial...

DE: Ich habe noch eine vernünftige Halterung für meinen Ender 5 Plus gesucht, in der ich den Bildschirm von BIGTREETECH unterbringen kann ohne dass es zu aufwändig wird oder gar eine extra Box an einer Seite steht. Ich finde das Design vom Ender 5...

Includes two screen holders, OEM((beta) please inform me of good print, thanks) and Reprap discount full graphics Meanwell PSU supported, info here https://www.youtube.com/watch?v=wyKYZ-oBXM0 Bow 5/64" 140mm x 83.5mm plexiglass to install on Meanwell...

Was needing a case for both of these components, I am slowly working my way to building the Mercury one.1. Only designs I could find required me to cut my stock enclosure, which I did not want to do. Hopefully this helps someone out. I modeled this...

At https://www.thingiverse.com/thing:4821969 jerryfudd designed a Ender 5 Plus Power Supply Casing Noctua 92x14mm RSP-500-24. ...I made this remix so that the openings fits for the new Noctua fan.

Purpose: - Mount the Pi 4 and a few buck converters in the stock case Note: - Designed to fit alongside the Meanwell RSP-500-24 PSU using the mounting adapters I made up - I also drilled matching holes on the opposite side of the case for extra...

Purpose: - Mount the Pi 4 and a few buck converters in the stock case Note: - Designed to fit alongside the Meanwell RSP-500-24 PSU using the mounting adapters I made up - I also drilled matching holes on the opposite side of the case for extra...

This is a modified Version of Marty_Z's Case https://www.thingiverse.com/thing:4790166 I needed a Case where my SKR2.0 Board, my RaspberryPi (aka Octoprint) and a DCDC downstepper (LM2596 for the fan) has space in. So i modified the Case... In the...

This is a Work-In-Progress.I wanted a new electronics case for my Ender 5 Plus. ...It had to open from the top. This is for the BigTreeTech SKR 2/3/3 EZThere are 2 variants:E5P Case v2.stl - SKR 2/3E5P Case EZ v2.stl - SKR 3 EZRemix of...

# Ender 5 Plus Case Replacement A remix of @Moederbeer case, I wanted to remove the large E5+ case enclosure and put the parts in a different container. I looked at a lot of cases, but couldn't find one I liked so I ended up creating this new one.

Remix TFT70 case that mounts over the hole of the stock screen on a Ender 5 Plus. Two clips center it and hold it in place. ...I used (4) 2.5x6 screws to hold the clips in place.

This is a magnetic snap-on case for the BTT TFT24 display to attach to a Ender-5 Plus printer equipped with a BTT SKR v1.3 or v1.4 board. Four magnets are holding the case onto the existing LCD cutout. Magnets: 4 pcs 10mm diameter and 2mm...

Mountings bracket to relocate the stock electronics enclosure on an Ender 5 plus to the rear of the machine outside the frame. This re uses the stock bolts that held the enclosure in the frame and M4 bolts and T nuts to mount the brackets to the rear...

This is a custom made Creality Ender 5 Plus complete bottom cooling case for ultimate cooling at half the noise. This uses 2 12v, near silent 60mm fans from RS components (RS Part number: - 696-3544) and 2 12v Noctua 40mm fans (NF-A4X20). Link...

I designed this case to move the Original screen outside the enclosure to make room for an SKR E3 Turbo mainboard. ...I used on the inside a mount from Thingiverse https://www.thingiverse.com/thing:4676133

I'm employing it successfully in conjunction with a Bigtreetech SKR v1.3 board that's been mounted using a simple adapter; as you can clearly see from the images, this configuration will definitely fit inside the Ender 5 Plus case. ...To my knowledge,...

Hi, here you can find a case for the BTT TFT35 V3. It is put on so that SD and USB are available. You need 8 x Ruthex M3 nuts -...

Case for Elecrow 7 inch touch screen and mount on Creality Ender 5 Plus

Custom electronics enclosure for Ender 5 Plus printer. Takes standard Meanwell power supply and heated bed MOSFET & standard touchscreen. Designed to work with either SKR 1.3/1.4 motherboards. Due to their size, they need to be printed on the E5...

Custom electronics enclosure for Ender 5 Plus printer suitable for BigTreeTech GTRv1.0 and M5 boards. Is designed to take standard Meanwell power supply, Creality heated bed MOSFET, Creality standard touchscreen (others will also fit), BigTreeTech...

Remixed to be able to print in two pieces and glued or bolted together. ...Second mount added on the front panel for another 40mm fan.

(Note) Meanwell cover changes pending 1/27/2021 Plus Wire Chase V5 deeper channel Added cover set for PSU Meanwell RSP-500-24 12/30/20 Plus Box B V41 added Creality OEM mounts for boards other than stock. ...Cut off a 2-3 mm of board posts in the way.

This will be updated if I do so when the BigTreeTech SKR 1.4 is installed in my Ender 5 Plus. (Files have "rev2" present as my initial design was tidied up and reduced in size a little to produce this one. No earlier revision has been uploaded.) ...

Enclosure for BigTreeTech TFT35-E3 dual-mode screen, for replacing the standard display on the Ender 5 Plus.Requires a total of nine M3 bolts, 8 mm minimum length M3 × 8 mm (or longer - up to 12 mm) ×7 – four for holding the TFT35-E3 board...

Feed the display cables through the hole in the case assembly, then snap the case into the Ender 5 Plus case's screen cutout. It should snap in with all six latches and have little to no play. 3. Connect the TFT43 screen and test whether it still...