ender 5 plus calibration 3d models

Disclaimer: I am not at all good at 3d modeling. I used Tinkercad to splice this up with some other mounting plate. ...Haven't tested/mounted it yet but it printed fine

<p>Remix of <a href="https://www.thingiverse.com/macderson">macderson</a> design from Thingiverse</p><p><a href="https://www.thingiverse.com/thing:4255482">https://www.thingiverse.com/thing:4255482</a></p><p>&nbsp;</p>

Just run the gcode from sd or octoprint Use feeler gauge or paper while adjusting knobs

This bracket provides a direct drop-in replacement for the stock Creality mount, accommodating the BMG extruder and filament sensor seamlessly. However, initial attempts to install the BMG extruder revealed that the filament path didn't align...

I will add photos once I have everything tidied up a bitThis houses the RPi so that the SD card can be accessed. All connectors are otherwise locked up inside the enclosure. I modeled a couple small support tabs inside the card slot so you can print...

I've been using the SpeedDrive mount as modified by @paydayxray for quite a while now, but haven't been thrilled about cable-tying the wire loom to the extruder spring or release lever. So I added a sturdy cable support. It looks a bit fragile at...

After installing the MicroSwiss all metal hotend and direct drive system the cables kept hitting the extruder and the filament lever. So I designed this cable guide that has an arm that rests on the extruder body and can be secured with an M3 x 15...

<p>RPi Cam holder/mount. It is forward facing and rear mounted above the spool location. Swivels left and right and pivets up and down. ...2/M5x10mm buttonheads bolts with T nuts and 1/M3x40mm bolts for pivet.</p> <p>Works for me.</p> Category: 3D...

This bracket lays flat on the printer case. It is designed to allow for the use of a Right Angle USB B to USB C Adapter so a Panel Mount Coupler, USB C Female to Type C Female can be mounted to the case. Works great for using Klipper on a Raspberry...

I used this design for my linear rail conversion, I'd used others but this one I felt had better Y brackets and the X cartridge bracket was great. The bit that I liked the most was the ability for you to print the X gantry without supports, the...

<p>This Adapter has the same holes as the original metal 3-wheel-carrige and is meant to be screwed to a MGN12h carrige.</p><p>I use it with a Hero Me Gen 6 printhead, but as the holes are the same, it <i>should</i> work with the stock printhead. The...

Right up front, I apologize - THIS IS A REMIX. Since Thingiverse REMOVED the ability to download all files that included identifying data on the thing you were downloading I could'nt find the original Thing number. That being said - if you designed...

Bracket to mount the BTT Octopus Pro board inside the E5+ enclosure using the stock board mounting points. The stock Creality bed Mosfet is removed and the bed heater is driven directly by the Octopus board - bed heater wattage falls well within the...

3.35mm gap, .1mm clearance of micro swiss direct drive gantry

Filamentsensor adapter plate 6mm thick when you upgrade to an dual gear extruder

The bolts on the bottom of the gantry mounting plate hit the middle of the bracket so i used tinkercad to hollow out a channel

I appreciated how solidly designed the BL touch mounting tab was on the original version, and how the Hemera mounting points resemble standoffs rather than a single large square, allowing for improved airflow around it. I didn't require the run-out...

The standard X-axis limit switch placement isn't exactly rock-solid. ...This mounting bracket adjusts the switch's position, ensuring a stable connection with the print head carriage instead.

This will help your rods being greased all the time when travelling up or down . the bracket will perfectly fit and slide over your bed and rod where you can ad a piece of foam keeping the rods greased and oiled all the time . 0.4 nozzle 0.2...

This Thing is for the cable chain tray from theaftab. ... It holds the cables for the direct drive unit just replace the original one with this item enjoy

This adaptor fits between the Microswiss and the Bigtree tech runout sensor

24/12/20 A remix to hold a ptfe tube for a direct drive, seems to be useless and i already change spool position for a better performance i were getting some isues with cable management and as a result i changed it. ... changing the design for an...

i will update this later with hardware requirements

This is a mix of the direct drive mount from paydayxray (https://www.thingiverse.com/thing:4310609) and the hot end side link from Gnizten (https://www.thingiverse.com/thing:4116655)

<p>Very quick and easy bed leveling test. ...The squares are 20mm each placed on every corner and middle of the bed.&nbsp;</p>

This is a remix of someone else's design that I modified to work with the exoslide system. ...Drops the front bar by around 100mm.

I used this design for my linear rail conversion, I'd used others but this one I felt had better Y brackets and the X cartridge bracket was great. The bit that I liked the most was the ability for you to print the X gantry without supports, the...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

Basic support to subject you carriage cables. Supports aren't needed if you use resolution 0,12mm and your funs works fine. UPDATES: · 10/05/2021 v.1.1 Modified width in the arms to ensure 3mm, to give more consistency. ... BOM: · 2 x M3...