ender 5 plus calibration 3d models

A remix from @bamcdo. I just changed the size of the holes down to 3mm which I used M3 screws to put through tightly and can use any sized washer >3mm in diameter. The original remix from bamcdo, the holes were just too big that I didn't have any...

Frustrated with cords constantly jamming into the limit switch and disrupting your printer? This is the answer. ... Design by: 3D PAT CA

Mounting plate adapter to use microswiss direct drive plate with the exoslide system To mount remove exoslide, mount plate to exoslide then mount plate to microswiss plate then mount exoslide back on rail

This is a mounting plate to put the BTT TFT70 on the lower right front corner of the machine. I got fed up with not having a place to put it, so this solves my issue. I printed in PLA for the draft that you see in the photo, but you may want to...

Changed the Desgin a bit because i had the problem that my modded fan duct hit the thing while leveling.

I used self adhesive strip LED lighting on the inside of my e5+ frame and needed to diffuse the light. The clips are offset to clear the Y wheels so they don't get in the way and sit above the bed height, to avoid collision. I would advise 3 clips...

[Demo](https://youtu.be/RVPKp-yUJQA) ### Info I've tried brass brushes, but they're limited in size (if you use some common brushes available widely) and the melted filament stick too much to the wires so it's hard to remove it. This is a...

Remixed to be able to print in two pieces and glued or bolted together. ...Second mount added on the front panel for another 40mm fan.

Fixed the error where the wall disappear

resized the 5mm bore holes down to 3mm

Hardware needed: -M8 tap -M8 bolt -608 bearing

Support for the cable from the bed to the controller.

A basic table to hold the Sunlu Filament Drier under your print bed and off to the side so you can dry while you print!

HOW I MAKE IT: <iframe width="560" height="315" src="https://www.youtube.com/embed/RpIH-jXLHm8" frameborder="0" allow="accelerometer; autoplay; clipboard-write; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe> MATERIAL: ...

I remixed the Microswiss X_Carriage with 3 screwing positions for an inproved grip. On the right the M3 hole must be drilled to 4,2mm. ...The hole on the bottom must also be drilled (I was not able to edit it right...) It's my first time I was able...

Blocks are placed along the x-axis rail to ensure it aligns perfectly with the frame. First, loosen the screws holding the wheel carriages in place. Then, adjust each eccentric wheel nut independently on both sides of the carriage until they're...

<p>I use a Lerdge board on this and wanted to have dual Z axis endstops to keep my bed level.&nbsp;<br><br>You will need:</p><p>2 brackets<br>4 x M2*12mm socket cap or button cap screws</p><p>4 x M2 nuts</p><p>4 x M4*10mm button cap screws</p><p>4 x...

Lower holder for the heatbed guide rods, so there is more space for a larger hotend and / or fan duct. ... The original screws can be used, 4ea M4 nuts are also required.

for SKR2

Relocates the Y axis stop sensor to the back rail to allow for horizontal movement for exoslide plates

I modified these 2 items and remixed it to fit the back rail without needing any additional tools.

I changed this up to have a bit more on the end of the arm. I hate when a design is cut off. It looks weird. I also made the mounting holes for M4 flat heat screws, as that was what I had on hand. ...I T-nuts are also from the filament sensor that...

The Linear Rail Brackets from Ralp57 (https://www.thingiverse.com/thing:4487342) suggest what I felt was an unnecessarily complicated way to raise the Z screw and Z linear Rails. You need to raise the bed when fitting linear rails because the X...

designed a spool holder that bolts onto the side of the printer via m4 bolts and T nuts. ...than you use a 1 inch diameter dowel for the spools to sit on. note uses drkztan's m4 t nuts. BOL8x M4x12 bolts4x M4x16 bolts12x M4 nuts2'x1" dowel rod

SummaryHad issues keeping the hotend cables from catching the printer, so created a tall bracket to keep the cable up. since installing this (with two zip ties), i have not had any issues. Will need supports. ...i used supports with a 3-4% infill for...

Look how close that X-axis Stepper Motor wire comes to the rollers. ... Move that wire away from the rollers with this!

Installed different lead screw bushing and changed my bed to the Wham Bam system so the original version was too tall and would crash the bed into this. I redesigned this to be a press fit and connect to the underside of the 20x40 that mounts to the...

This is a motor mount designed to mimic the stock motor mount with the lower section where the filament runout sensor would be removed. I used this mount while working with the 3DChameleon MK2 as I needed a way to mount two motors side by side...

My version of the bed raise. I use 100mm M4 screws, as well as additional springs about 20mm (0.75in) in outer diameter. If you use springs which have been flattened you probably won't need the spring keepers. I remixed the motor side riser to...