ender 5 plus calibration 3d models

The original hook placement was moved to the front face to make this holder compatible with the entire Ender 2/3/5/5 Plus and CR-10/S/S Pro series, as well as any other printer using a standard 20mm T Slot Extrusion profile (2020, 2040, etc). The...

Therefore, here it is: This is a revised version of Full Graphic Display Case for Creality CR-X by Mouses ( https://www.thingiverse.com/thing:3369685 ), specifically designed to work with the Ender 5 Plus, which also comes equipped with a somewhat...

The base is designed for the Ender 5 Plus, but should theoretically fit the Ender 5 and other Creality printers too. I've uploaded the STEP files, so feel free to remix the system to fit your printer model! Just give me a shout-out because it took a...

This is a X and Y axis linear rail conversion kit for the Ender 5 Plus with Biqu H2 V2S extruder. It is designed to be durable, low profile and lightweight.A durable and heat-resistant material should be used, PolyMax Polycarbonate is strongly...

Replace your original Ender 5 Plus screen with a Raspberri PI zero 2W and a 3.5" LCD RPI SPI. ...Go for Klipper and KlipperScreen!Full instruction and files in order to configure Klipper are herehttps://github.com/ploucandco/Ender_5_Plus_KlipperScreen

This is a drag chain mount from the Ender-5 Plus frame to the X-axis where the drag chain is mounted behind the stepper motor on a Micro-Swiss direct drive mount. You would need the following set of screws and nuts to make this work. To mount the...

... orientation. Thanks to the original creator and the other remixes for inspiration. I use soldering iron to heat press the aluminum v-wheel spacers into the mount. Printer I used is actually and Ender 5 Plus, not listed in printers list yet.

This is a remix of the BMG mount made by Oaklandishh with a few changes made: - hotend fan adaptor to suit larger style fan - 2 types, one that is bent up at the front to clear the front extrusion on the ender 5 plus, or one that would most likely be...

... port, you will need a short piece of Capricorn, approximately 15 mm long. Begin by inserting a longer piece and trimming it down gradually until it fits perfectly. This solution may also be applicable for the Ender 5 and Ender 5 Pro models.

This is a custom cooling solution for an NF-Crazy Plus hotend on an Ender 5 Pro.The NF-Crazy Plus is a Mosquito clone that is wider than the original Mosquito, but also mounts using the stock Creality mounting solution rather than the Mosquito's. If...

Ich stelle hier mal meine selbst erstellten Halteclips zur Verfügung, mit denen ich meinen Creality Ender 5 Plus mit einer LED Beleuchtung ausgerüstet habe. Die Clips werden einfach nur auf den 20x20er Aluminiumrahmen aufgedrückt. Die Halteclips...

Hey guys, this is "just another" system of E3D Volcano shrouds, for the Ender 5 Plus in this case. I designed this specifically to operate the machine with PCTG, without the hassle of setting up a water cooling system (that would be my fourth,...

Hey guys, this is "just another" system of E3D Volcano shrouds, for the Ender 5 Plus in this case. I designed this specifically to operate the machine with PCTG, without the hassle of setting up a water cooling system (that would be my fourth,...

Adapter for Creality Ender 5 Pro filament run-out sensor and upgraded dual-gear extruder: e.g. AliExpress item 33041468821.\r\n\r\nTwo versions available, compatible with either inset M3x5mm bolts or surface mount M3x8 mm bolts.\r\n\r\nDesigned from...

These are my custom config files for the Ender 5 Plus with Marlin 2.0 Firmware on a SKR 1.3 motherboard (I have a 1.4 Turbo installed, but I haven't had time to update it yet). They are very specific to my machine, but I thought others might find...

I provide here my self-made clips, with which I have equipped my Creality Ender 5 Plus with LED lighting. The clips are simply pressed onto the 20x20 aluminum frame. The retaining clips hold an LED light bar on mine in addition to a Gopro Hero 7...

It is designed to fit the MicroSwiss Direct Drive plate for the Ender 5 Plus, as shown in this model: https://www.thingiverse.com/thing:4563691 You might be able to fit it on the narrower original MicroSwiss Direct Drive plate, but it's shaped...

I plan on raising up my 5 plus by 100mm to drop the power case under the extrusion so i can put an enclosure across the top of the lower extrusion and keep the case and Z motors underneath the lowest sheet of enclosure. i put in some holes to the...

You can get the kit directly from MicroSwiss at: https://store.micro-swiss.com/collections/extruders/products/micro-swiss-direct-drive-extruder-for-creality-ender-5 . . ... Disclaimer: The thingiverse.stl file is not for use, only as it is required to...

For the X-axis of an Ender 5, installation occurs without modification. The belts are accurately aligned for the 20t 2GT pulley, situated in the 2020 extrusion. Additionally, this design includes a BLTouch mounting option with spacers. It requires...

Spacer for use with Creality Ender 5 Pro filament run-out sensor and upgraded extruder with dual gears: e.g. www.aliexpress.com/item/33041468821.html Two versions provided, for either inset M3x5mm bolts or surface mount M3x8 mm bolts. Built using the...

This is a remix from an stl file of the MicroSwiss Ender 5 DirectDrive backplate uploaded to thingiverse. . . I made this so everybody can make their own fan ducts for their setup (although I have designed one for three 40mm axial fans:...

The Calibration Test for Your Ender 3 is Waiting to Be Started. Please Place Your Printer on a Level Surface, Then Follow These Steps to Complete the Calibration: 1. ...Measure the Bed: The bed of your Ender 3 measures 220 x 220.

Conclusion : Ventilateur plus grand = plus d'air pour ventilé l'électronique. Attention ! Pour que cela ne gêne pas dans le boitier, il est impératif de prendre un ventilateur de 80x10mm. Modèle utilisé :...

Conclusion : Ventilateur plus grand = plus d'air pour ventilé l'électronique. Attention ! Pour que cela ne gêne pas dans le boitier, il est impératif de prendre un ventilateur de 80x10mm. Modèle utilisé :...

It is specifically designed to fit an Ender 5+ with 4020 hotend fan, Micro Swiss hotend, and the ExoSlide gantry upgrade. Not sure if anyone else out there has that setup, same as me, but if not, you might be able to mod my mod for yourself... ...

Hotend and part cooling fan for the MicroSwiss Direct Drive. It is tight in the X direction but you wont loose any build volume, Y is at 46mm not larger than stock. BL-Touch location: X: +8mm Y: -23mm Stuff needed 2x 50x50x15 Fans 6x M3x5 (if you...

I made a large 90 degree bracket for the 2020 extrusion. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0,2 Infill: 15 Cubic Filament: CR-3D PLA Gold Category: 3D Printer Parts

https://www.thingiverse.com/thing:586673 My goal was to fit the design on my Ender 3, but I couldn't find a simple solution that would be easy to adapt to various spool sizes and thicknesses available in the market. The design features an 8mm bolt,...

This is a mix of the direct drive mount from paydayxray (https://www.thingiverse.com/thing:4310609) and the hot end side link from Gnizten (https://www.thingiverse.com/thing:4116655) This version has a 9mm Y offset to be compatible with HeroMe Gen 5