ender 5 plus calibration 3d models

I relocated the electronics enclosure on my ender 5 plus to sit outside my enclosure. There is a small fan on the bottom of the box that is designed to cool the electronics components inside, so these feet lift the box off the table slightly...

This holder consolidates all of the hex keys, wrenches, and the screw driver that comes with the Ender 5 Plus. It also has an extra slot to keep a razor blade in. ...The lid may be a tad loose depending on your printer, so you can add some tape to add...

The Ender 5 Plus can be elevated by placing this foot under it, utilizing the stock feet provided. The foot features a tapered recess at the top that cradles the stock feet in place, preventing them from slipping or tilting. ...With this riser...

Leveling feet for the Ender 5 Plus. A full set will require the following components: (2x) Part1-Mount-LH, (2x) Part2-Mount-RH, (4x) Part3-Foot, (4x) Part4-JamNut, (8x) M4x10 screws, (8x) M4 T-slot nuts. ... You can stick some foam tape or rubber dot...

The workbench I wanted to set my ender 5 plus up on was a bit smaller front to back than the footprint of the printer, so I made this doohickey. Just shove it under the feet along the edge of the surface it should accommodate the overhang. ... Use...

Pattern to see which corner needs to be set with Ender 5 Plus. Set your layer height to 0,2mm and you will have 2 layer. For bed equale or larger then 350mm x 350mm. ... *** WARNING*** Paper clip of the front left corner must to be move to...

This is a remix for an Ender 5 Plus - will require 2 of these pointing at the printed object. ... Will be printing in the next day or two to test - any issues I will update this Printing on my E5+ using PETG as that is what I currently have it set...

Summary This is a filament lead in tube (Bowden) end holder for Ender 5 Plus direct extrusion modifications. It is designed to hold the end of the filament lead in tube from the filament break detector to the direct extruder. The filament bracket...

... addition to mount LED strips facing to the print. ...Fits nice on my Ender 5 Plus. ...Maybe also on other Printers Before printing, lay it on the back in your slicing software to avoid support-printing Printing: Infill 10% Speed 100%

a simple low profile cable clip of the ender 5 plus hot end cable aka 1/2" split loom. ... for assembly: (2) M5x10 screws (2) M5 T nuts (1) 8" cable tie Second version to re-use shorter screws Tip: Add a second clip for added support

This thing was created using Tinkercad. ...Edit it online at https://www.tinkercad.com/things/b8Y8tFp5kVM. This is a remix of the original design, modified for use with the Ender 5 Plus. ...Simply remove the top bar to enable smooth sliding motion!

I just made this quick thing, it covers the metal sliders on the Ender 5 Plus the bed uses to go up and down evenly. Doesn't affect the way it works, just makes it so you can change the colour from a metal to what ever colour you want. ...It fit...

I made a huge drybox setup and use the bowden filament adapter on my CR10S Pro but I changed to a Ender 5 Plus. The Filament adapter does not fit it and the CR-10 V2 Filament Guide looks great but was slightly too small due to the plate the the...

Original Model: https://grabcad.com/library/creality-ender-5-plus-1 The process for using it in Simplify3D: You would want to put the file into the folder: C:\Users\**USERNAME**\AppData\Local\Simplify3D\S3D-Software Then go into Simplify3D and go to...

Designed for the Ender 5 Plus, but should fit any printer that uses 20mm x 20mm rails. https://www.amazon.com/dp/B071F1K7BJ?ref=ppx_yo2ov_dt_b_product_details&th=1 Use with 1.75" in, 30-durometer, Sorbothane hemispherical feet. I bought the...

I designed a top cover for my Ender 5 Plus that blocks using other snap-on strain relievers, which led me to create something new. Additionally, I aimed to design parts with no assembly required. To use this one, align the t-nut and twist it...

Hello all out there, here is a proposal for adjustable foot on ender 5 plus printer. Schould fit any 2020 profil frame based printed. You will need : to mount the foot : 4xM4x10 screw and the same amount of T-Nuts For the feet : M5x30 flat head...

This is a Modification for the Ender 5 plus, The Silent Board has been replaced with the Lerdge K Board I replaced the original Extruder, and get it upwards, so the stringing becomes less or none!! Replaced the Filament holder I also replaced the...

... motors than the smaller one is just fine. Also both are now correctly orientated. Print Settings Printer: Ender 5 Plus modified Rafts: No Supports: No Resolution: rough is good enough Infill: 50 Filament: any PLA Category: 3D Printer Accessories

I designed a top cover for my Ender 5 Plus that made it impossible to use snap-on strain relievers, so I created this new solution. I also wanted to design parts that require no assembly. To install, simply align the t-nut with the print head and...

However my Ender-5 Plus does not expose any such ends and I was reluctant to remove one of the existing covers. ... So I combined the USB holder cup with a V-slot clip from https://www.thingiverse.com/thing:3361395 into a new holder that clips on the...

Ender 5 Plus extruder relocation mount to move it from the back of the printer to on top of the rear frame. I moved it up here for easier access to help with filament changes for multi-color prints. No wire extensions needed, however requires 2x...

I remixed the Ender 3 Wyze Camera Mount to fit the Ender 5 Plus. This will probably work on other printers. The mounting holes are 20mm on center. I used two 4mm button head bolts I my bolts were 10mm long and it was barely enough. I also used two 4...

This simple mod - if it even deserves to be called that - is probably a perfect addition to Daede's "Ender 5 Plus 120mm Fan Control Box Cover." The Clearance under the control box is ~38mm with this feet-offsets, so when using 25mm Fans there's still...

I used the mount from thingiverse https://www.thingiverse.com/thing:3114139 by Skrutt84 to attach to the ender 5 plus original bracket. Material list 1 pc of 5/16 threaded rod 5 1/4" long 2 5/16 lock nuts 4 5/16 washers 2 608zz bearings. ...

This is a remix of https://www.thingiverse.com/thing:4548894 That was remixed from eric-anastas Satsana for the Ender 5 Plus. I added a taller wire strain relief and adjusted it to better fit around the belt protrusions. I have printed it and it is...

How to install: Unplug power from your outlet Tip the ender 5 plus on its side and remove the lower cover to access the power supply Remove the four m4 screws that hold the power supply in place and make sure you hold onto the power supply so it...

Ender 5 Plus cable trunking and covers. I have uploaded the trunking and lid in 15mm lengths to save space. You can resize them to suit in your slicer. The trunking is best printed vertically to add strength to the slot grips and require...

This is a spool holder designed for the Ender 5 Plus. It has a shoulder on the base which will fit into the bracket to allow 90 degree rotation for placement of the bracket. It also is shorter than the other ones posted on Thinkiverse to allow the...

Ender 5 Plus LED light bar top frame. Provides a top protective frame at the top of the printer to affix self adhesive LED strips to. Additionally clear sides and top could be added to add additional cover. Fits the the original L brackets of the...