ender 5 plus calibration 3d models

I created these inner channel clips to keep your Ender 5 plus cables hidden, neat and tidy within the frame. There are two sizes you can use (small & big), it depends on how many cables are in the channel, you'll use the small or big one. Print it...

A custom strain relief for the Ender 5 Plus extruder, crafted with precision using PLA and optimized settings from the factory slicer. To bring this design to life, you will need: 1. An M3 x 12mm Button Head Socket Cap Screw 2. A set of M3 Flat...

... of the clip. The original clips kept popping out or falling off the extrusions with ease, so I gave them a makeover by remixing the Ender 5 Plus Wire Clip design. ...This new version fits more securely and stays put even when accidentally bumped.

Tube guide for the Creality Ender 5 Plus to avoid contact with the drive axis. The tube with the wiring for the hot end slides between the drive axis and the frame. The part is mounted on the rail with two T-nuts and M5x12 screws. The tube can be...

A simple tool for you to align the dual z axis on your Ender 5 Plus. Print 4 of these and place on the smooth rods. You can print the block in solid or without top and bottom. If you only have 1 stepper driver for dual Z and cannot preform Marlin...

This is a remix of the Ender 3 Z-axis endstop to use on the Ender 5-plus. The area that holds the endstop board is basically the same, but enlarged and reshaped slightly to fit the endstop boards I have. It was also changed to use M3 heat set...

The jetpack has been halved and will fit on an Ender 5 Plus bed and print without supports. To put the halves together I have added dowels and pocket screws. I've also put in some screw holes at the back and adapted the way the rockets are fitted so...

I used the E3D Volcano mount to attach the Spider to the Ender 5 Plus. This allows you to position the Spider at the same z height as the stock hotend. You mount it upside down from the pics in the link: ...

I wanted an LED strip light for my Ender 5 Plus, but all I found was this one for the standard Ender 5: https://www.thingiverse.com/thing:4125317 Front and rear lighting is nice, but it wasn't wide enough for the Plus so I needed something bigger. ...

... of the bed is necessary to ensure adequate printing height, given the adjustment to the 8mm rod brackets. Following these modifications, the risk of collisions is eliminated, allowing seamless integration with the original Ender 5 Plus firmware.

VIDEO: https://www.youtube.com/watch?v=RpIH-jXLHm8 ENDER 5 PLUS: https://bit.ly/2YHzpws BMG: clon:...

---------------------------------------------- This is an adaptation of my unpublished Ender 5 Duet Mount, modified for the Ender 5 Plus. It utilizes a 40mm fan (recommended: 24v SUNON 4020 or 12v Noctua 4020 via a buck converter) to direct air...

This is a bracket for the Ender 5 Plus controller case to move the cooling fan from the bottom to the rear of the controller case and cover the fan's old hole. The air will now be pulled in the front sides and exhausted out the back. The bracket...

This mount allows to use the stock extruder of the Ender 5 Plus to be used as direct drive extruder. Installation: 1.) Unscrew the fan chassis, the BL-Touch sensor as well as the hotend 2.) Disassemble the upper two mounting wheels of the...

Hello all, Here's an ajustable webCam support for Ender 5 plus ... or for all printers that has 2020 profil All the parts can be printed without support except for part 7. All the parts are printed mostly on the side edge so that the holes are...

A light bar for the Ender 5 + may fit the Ender 5 pro. Wide enough to hold normal LED's or the Neopixels. ... Wire holders on both sides so you can hold the cable.

Cover for the Meanwell Ender 5 PSU to go with the complete bottom cooling case. ... No supports needed

Remix of Ender 3 - Filament Holder Deluxe (https://www.thingiverse.com/thing:3114139) for Ender 5 Plus (tried to upload it as remix, but Thingiverse is not able to find the original design) - I was happy with the original design that I have used on...

Not sure where the original design came from but I have it on my ender 5. Bought a 5 plus and wanted to add similar protection to the BL touch. ...Quickly discovered that I needed to add a few mm to it in order to maintain the clearance of the rail...

Mountings bracket to relocate the stock electronics enclosure on an Ender 5 plus to the rear of the machine outside the frame. This re uses the stock bolts that held the enclosure in the frame and M4 bolts and T nuts to mount the brackets to the rear...

This piece supports the wire going to the hot end on the Creality Ender 5 Plus. The V4 file is designed to connect to the printer with two M3x10 machine screws and two M3 T-nuts, while the tube connects with a zip tie or twist tie. This piece...

This is a Ball-Bearing Filament holder for Creality Ender 5 Plus (or possibly other models) designed to accommodate filaments weighing 1000g or less with an inner diameter of 52mm. To complete this project, you will need two sealed ball bearings...

When you get your aliexpress linear rails for your Ender 5 plus, you might get install blocks as pictured, luckily I did. Those install blocks are inadequate since they end up putting the X gantry far too high on the top 4020 channel. Drop the rails...

Aluminum LED Channel brackets for the Ender 5/ Plus printers. You will need to print two of each file for all four needed. The brackets do not have holes for the wiring, but 10 seconds and a drill bit will put the hole wherever you want it. ...

Simple but effective replacement for your Ender 5 Plus duct fan. Exhaust in under small angle (now with rails) so air flow is pointed directly to the tip of the nozzle. Hope you will be happy with the results. In case of any problems or tips do not...

I encountered a problem with my Ender 5 Plus in that the front was lower than the back even when everything else was equal. This led to rear adjustments being significantly tighter than the front and became an issue when I switched to solid silicon...

This is a housing for the Mini 12864 LCD display to fit inside the Ender 5 Plus chassis without modifications. It bolts on from inside using the original mounting points and screws. You mount the LCD to the back cover first with the M4 screws and...

This is a filament lead in tube (Bowden) end holder for Ender 5 Plus direct extrusion modifications. It is designed to hold the end of the filament lead in tube from the filament break detector to the direct extruder. The filament bracket installs in...

Since uploading my Ender 5 Plus Micro Swiss cable support bracket, I have redesigned a bracket to fit at the end of the X Gantry to mount the cable on to support it away from the metal frame and the wheels on the gantry. You will need to install...

One was for Ender3 and the other was a rough Ender 5 Plus design that needed jesus. This should be usable with the Ender5+ with little to no modifications to your printer. It uses the default hardware. BLTouch mount is about 5mm to the left of the...