ender 5 plus calibration 3d models

I completely remade his mount from scratch to work with the Ender 5 Plus (though presumably, it would also work with other Ender 5 models) This Thing only comes with the bracket and modified BL touch bracket. You still need one of his cooler fang...

Can be used for Creality Ender-5, Ender-5 Plus, Sovol SV05, and maybe other printer with similar shapes i dont know. Supports required from build platform. Mounting on the 2020 profile using T-nuts, 5 holes available, I only use 3 mounting points...

... to increase the sides to 3mm instead of 1.5. I also increased the thickness on the mount for the Ender 5 Plus because I found that the original "wiggled" too much on my printer when mounted. ... I added two additional screws to the block as well.

I needed a filament guide when I upgraded my Ender 5 Plus to direct drive. With this I could have the filament spool sitting the same place as before. This is mounted instead of the old extruder. Hardware required: 2 x M3 Bolt 2 x M3 Nuts M6...

Inspired by a fantastic video from Tripod in his garage, where he provides an extremely detailed walkthrough of installing Bigtreetech's SKR 1.4 into an Ender 5 Plus, based on KAY3D's Cheetah 5.0 Marlin Firmware. Since I had acquired several SKR 1.4...

Also included is an over-the-top tool caddy because the ender 5 plus has a lot of vibration noise when loose things are mounted to the frame (Especially noisy in the Y axis movements!) So this allowed me to remove all tools from the frame and still...

Work in Progress Remix of the TeachingTech Concept: Please note that this concept differs from the original due to the specific format of the Ender 5 Plus! To build a case for the Ender 5 Plus, you will need: - 4 V-slot profiles of 495mm - 4 V-slot...

Also included is an over-the-top tool caddy because the ender 5 plus has a lot of vibration noise when loose things are mounted to the frame (Especially noisy in the Y axis movements!) So this allowed me to remove all tools from the frame and still...

Perfect mount for the Reolink E1 on the Creality Ender 5 Plus Fastening material: 2x cheese head screw M4 x 10mm 2x hammer nut for 6mm nut. Thread M4 Attention! ...I printed it out of PLA, if you often print ABS or ASA with a enclosure, please...

The electronics changes include: TH3D Parts: * EZboard Lite: https://www.th3dstudio.com/product/ezboard-lite/ * Dual Z Stepper Motor Adapter with Cable: https://www.th3dstudio.com/product/dual-z-stepper-motor-adapter-w-cable/ * Heated Bed MOSFET:...

Precision Leveling System for Ender 5 Plus. Using the standard M4 screw, this Leveling System allows z-adjustment of 0,05mm per step. This version is desined to fit a ISO nut M4. If there is intrest, i will upload the adjusting wheel with the hole...

A simple wire support for your Ender 5 Plus hotplate should fit others just as well. Secure it with cable ties under the hotplate mount right next to the bed leveling screw. The first test print was made with HIPS, extruder temperature at 240C, and...

I wanted to mount a second one of these cheap hygrometer/thermometer on the back of my ender 5 plus enclosure. I had extras anyway. This version mounts on the back corner of the extrusion and leaves plenty room in the back for air circulation. I...

I wanted a sleek light bar for my Ender 5 Plus, but every standard LED strip didn't fit, so I grabbed xqqqqme's clips and gave them a makeover to match LilTrublMakr's bar perfectly. I removed the v-slot modification and here's what I came up with -...

The way I have my Ender 5 Plus set up, a cable sleeve just dangles loosely and frequently scrapes against the printer's frame. This is the first modification I've made to the printer. I printed the part with 40% infill, 100mm/s speed, .2mm layer...

This is a remix from an Ender 5 plus Z sync indicator by bamcdo. It's minimal design. You need to mirror to fit the other side. You need to use the original pointing model from JonathanA66. The original models did not fit to me, because both they...

quick and easy guide for the ender 5 plus hotend loom. Needs 2x 3mm T-nuts to mount to the back rail. I used PETG but I'm sure PLA would be fine. Just make sure the hole is smoothed out (some nibs from z-seam might want rubbing down) so the harness...

I recently purchased a new extruder gear for my Ender 5 Plus. It's a knock off Bondtech Geared extruder, but works well. However the new gears put the filament path about 9mm higher than stock. I designed a simple spacer to accommodate the increased...

This is my first post on Thingiverse, I wanted to add more color to my Ender 5 Plus so I re-created the corner brackets to be printed in any color you wanted. I did a 20% infill, Layer Height of 0.2, wall thickness of 0.8 and did use supports for...

I'm using it on my ender 5 plus inside the enclosure to monitor both temp and humidity in there. It mounts with 2 m5 screws and a couple Tnuts. Step file included for those of you that need or want to modify it. ... Be sure to use support when...

This is my version of LED strip support for ENDER 5 PLUS. Is to be print with support , back on print plate. there is a left, and right part, but they are quiet similar, so maybe no matter if you print only one piece twice. You will need : 16...

... stop. ...I was having issues printing on the 5 plus and discovered that the PLASTIC corner braces were cracked. I replaced them all with machined aluminum and the printer is now very rigid. ...I made a remix of the ender 3 bracket for the limit stop.

EN: I have developed a dual nozzle conversion for the Ender 5 Plus or for all printers with the usual roller guide system. The original mounting plate was modified and re-milled from aluminum. I tested it with a PETG prototype before milling, and it...

I designed this to replace the boring black limit switch covers on my Ender 5 Plus with no additional hardware needed. They will also work on limit switches on other Creality machines, but you will need two M3x14 screws. I have test printed this...

I designed a low friction spool holder to fit the Ender 5 Plus bracket, and it turned out to be too slick. The spool would spin freely on its own without any assistance. To correct this issue, I inserted some packing foam between the spacer and the...

Since I'm not using the stock Ender 5 plus display, I've remixed a BTT TFT35 mount with a 40mm fan grille. Just an easy no case modification required to add another cooling fan to the case. ...Should fit any 40mm fan, screws for fan mount are M3 length...

I made a housing to fit the BTT mixing 2in1out extruder that can be mounted on the Ender 5/plus backplate. The hous is made for 2 40x40x10 fans on the extruder cold end an is directing the air up away from the buildplate. I also remixed the layer fan...

This is actually inspired by WyvernPL's fan duct for the Ender 5 Plus. I aditonally made a adapter part to replace the PSU fan with and put the fan grill inside the housing so it is completely flat on the ouside. The tube is raised at the larger end...

... this one in PLA+ for testing. Decided to go another route, but if I had kept it I would've reprinted in PETG. Printed great on my Ender 5 Plus, I added 3 perimeters(for a total of 6) and 10% infill(for a total of 25%) for some added strength.

I wanted to mount a Voron M4 Extruder to my Ender 5 Plus while retaining the stock filament runout detector so I designed this piece to mount it much like the stock extruder. ... You will need 4 M3 screws and nuts to mount the runout sensor, 3 M5...