ender 5 plus 3d printer

My Ender 5 Plus has the Micro Swiss NG extruder and hotend so I took the parts from the one this is logged as a remix of and the Kersey Fabrications parts (https://www.thingiverse.com/thing:3646827). The Y rails go on the outside of the...

---------------------------------------------- This is an adaptation of my unpublished Ender 5 Duet Mount, modified for the Ender 5 Plus. It utilizes a 40mm fan (recommended: 24v SUNON 4020 or 12v Noctua 4020 via a buck converter) to direct air...

This mount allows to use the stock extruder of the Ender 5 Plus to be used as direct drive extruder. Installation: 1.) Unscrew the fan chassis, the BL-Touch sensor as well as the hotend 2.) Disassemble the upper two mounting wheels of the...

This is a bracket for the Ender 5 Plus controller case to move the cooling fan from the bottom to the rear of the controller case and cover the fan's old hole. The air will now be pulled in the front sides and exhausted out the back. The bracket...

A light bar for the Ender 5 + may fit the Ender 5 pro. Wide enough to hold normal LED's or the Neopixels. ... Wire holders on both sides so you can hold the cable.

Cover for the Meanwell Ender 5 PSU to go with the complete bottom cooling case. ... No supports needed

Due to the Ender 5 Plus's independent Z screws, they can easily get out of sync, making it a challenge to maintain proper alignment. Removing any part can cause the bed to fall and become misaligned. If you're like me and don't run auto-bed leveling...

When you get your aliexpress linear rails for your Ender 5 plus, you might get install blocks as pictured, luckily I did. Those install blocks are inadequate since they end up putting the X gantry far too high on the top 4020 channel. Drop the rails...

Simple yet effective replacement for your Ender 5 Plus duct fan. Exhaust is directed under a small angle, now featuring rails, so airflow points directly at the nozzle tip. I hope you'll be satisfied with the results. If any issues or tips arise,...

Simple but effective replacement for your Ender 5 Plus duct fan. Exhaust in under small angle (now with rails) so air flow is pointed directly to the tip of the nozzle. Hope you will be happy with the results. In case of any problems or tips do not...

Since uploading my Ender 5 Plus Micro Swiss cable support bracket, I have redesigned a bracket to fit at the end of the X Gantry to mount the cable on to support it away from the metal frame and the wheels on the gantry. You will need to install...

This is a filament lead in tube (Bowden) end holder for Ender 5 Plus direct extrusion modifications. It is designed to hold the end of the filament lead in tube from the filament break detector to the direct extruder. The filament bracket installs in...

Mountings bracket to relocate the stock electronics enclosure on an Ender 5 plus to the rear of the machine outside the frame. This re uses the stock bolts that held the enclosure in the frame and M4 bolts and T nuts to mount the brackets to the rear...

I encountered a problem with my Ender 5 Plus in that the front was lower than the back even when everything else was equal. This led to rear adjustments being significantly tighter than the front and became an issue when I switched to solid silicon...

First time doing something like this, and there's still some unnecessary artifacts from my quick hob-job. Print Settings Printer Brand: Creality Printer: Ender 5Rafts: No Supports: NoResolution: .2 Infill: 100 Filament: [...

This will be updated if I do so when the BigTreeTech SKR 1.4 is installed in my Ender 5 Plus. (Files have "rev2" present as my initial design was tidied up and reduced in size a little to produce this one. No earlier revision has been uploaded.) ...

I created a mounting bracket for the BigTreeTech PiTFT50 screen to fit on an Ender 5 Plus. The design is in 2 parts (plus the retaining clips). Because of the way it's designed, you can still mount the Pi on the back of the display if you wish. ...

This model is designed to fit a Vizio xr6m10 tablet (5.5 x 3.5 x 0.2 inches), but you can easily update the model to work with other phones/tablets by tweaking the [Tinkercad...

A compatible light bar for the Ender 5 Pro is the same size as the one used for the Ender 5. It offers ample space to accommodate standard LED lights or even Neopixels. ...The design includes wire holders on both sides, allowing users to neatly manage...

This is a complete overhaul of the ender 5 plus's gantry. After trying the Merc One core-xy mod, I found that the belts were far too long to prevent ringing, and the belt path too complex to avoid problems. Also, the stock belt arrangement really...

This is a custom made Creality Ender 5 Plus complete bottom cooling case for ultimate cooling at half the noise. This uses 2 12v, near silent 60mm fans from RS components (RS Part number: - 696-3544) and 2 12v Noctua 40mm fans (NF-A4X20). Link...

Update: - Added a V2, just slightly bigger holes for the bolt and allen key making them easier to fit Purpose: - Liked the original, but like requested in the comments for it, I also wanted M5 fitments - Removed internal filleting and recess -...

I am currently working on turning my Ender 5 Plus into a high temp filament machine. In that endeavour I realized that I would have to move all my electronics outside the main body so that I can use 1/8" acrylic in the frame as an enclosure. So I...

This fan shroud is designed to precisely fit an Ender 5 Plus with Spider Hot End using the HBE X Carriage (purchase on eBay). It allows the reuse of the factory fans. It is based on https://www.thingiverse.com/thing:5369808 and uses the plate that...

To upgrade the Ender 5 Plus, you'll need to gather the following essential components: 1. Three 450mm MGN12H rails 2. Three MGN12H bearings 3. Sixty-six M3x8mm bolts 4. Sixty-six M3 T-Nuts The total cost for these parts will be approximately $120. I...

This is a bracket to relocate the front crossbar of the Ender 5 Plus to get a better view of the build plate. You may locate the crossbar at any height you find suitable for your setup. Also consider printing the End Covers that protects you from...

Ender 5 Plus Bowden tube & cable guide =============================== I was frustrated and annoyed because of the inconsistend layer print behavior which lead to bad looking surfaces. I managed to find out, that this was related to the...

I used these to help stabilize the long 2020 extrusions to the 2040 extrusions on my Creality Ender 5 Plus. These can be used on any frame that incorporates the 20 series extrusions. I uploaded multiple variations depending on your preference. There...

# Ender 5 Plus Case Replacement A remix of @Moederbeer case, I wanted to remove the large E5+ case enclosure and put the parts in a different container. I looked at a lot of cases, but couldn't find one I liked so I ended up creating this new...

Made this for ender 5 plus to attach cable chain to extruder in a direct drive setup. I could not find anything with key words to find something. So I made it. This is just the brackets to mount cable chain from...