ender 5 plus 3d printer

One was for Ender3 and the other was a rough Ender 5 Plus design that needed jesus. This should be usable with the Ender5+ with little to no modifications to your printer. It uses the default hardware. ...BLTouch mount is about 5mm to the left of the...

Creality3D Ender-5 Plus (EN) https://bit.ly/3eZtzQi Creality3d Ender-5 Plus (JP) https://bit.ly/3qH6m8C 日本のみで使えるクーポンや、Creality3Dのマシンを正規購入する方法をまとめてあるので是非チェックしてみてください。 https://www.psych0h3ad.tech/entry/info/3dprinter/creality バーLED...

Creality3D Ender-5 Plus (EN) https://bit.ly/3eZtzQi Creality3d Ender-5 Plus (JP) https://bit.ly/3qH6m8C 日本のみで使えるクーポンや、Creality3Dのマシンを正規購入する方法をまとめてあるので是非チェックしてみてください。 https://www.psych0h3ad.tech/entry/info/3dprinter/creality バーLED...

However, I had great success with this mod on my previous Ender 5 printer, so I applied the same principles to the Ender 5 Plus. Many of the printed parts are for TH3D products, which required extra space and mounts to hold them in place. This...

Remixed an ender 5 plus fan duct to fit on my fan. ...The previous one had some extra plastic on that the screws go through and didn't fit on mine.

Filament tube guide for the stock extruder setup on an Ender 5 plus. This support angles the tube at 10 degrees towards the bed. ... Hardware: 2) M3x16 screws 2) M3 t-Nuts

Ender 5 Plus Z-axis supports. Has slots (for flexibility) for M5 screws with a counter-bore for flush mounting. ... The bearing used is a 608, in this case a ZZ as I had them already.

This bed wire strain relief device mounts directly to the 2020 extrusion that forms the Ender 5 Plus's bed support, securing itself with M5 bolts and 2020 T-nuts without needing to disassemble the bed or any other components.

Couvercle Magnétique pour Ender 5 Plus. Fini les mouches, moucherons, moustiques attirés la nuit par l'éclairage de l'écran. Une couvercle simple et efficace. Nécessite 4 aimants de 12x1mm... ...et un peu de colle.

I couldn't get the original spacers to fit the bearings on my Ender 5 Plus. I broke several trying so I resized the spacer to 15.99mm. ...Now it slips on with a tight fit and stays in place.

I'm implementing a Simple Patch for the Ender 5 Plus Filament Sensor. ...The Problem is that it's registering a False Empty Reading whenever the sensor gets nudged aside by the filament.

Remix TFT70 case that mounts over the hole of the stock screen on a Ender 5 Plus. Two clips center it and hold it in place. ...I used (4) 2.5x6 screws to hold the clips in place.

If you have an Ender 5 Plus with a Wham Bam bed, you can use this stl file and image to set it up in Prusa Slicer. Print instructionsNo printing required

This is an Adapter for the tubing of the Polybox to connect properly with the Ender 5 Plus. ... This is A Remix of the of the Design by Doloth https://www.thingiverse.com/thing:4249749

Heated bed control block found inside the Ender 5 Plus. ...Does not include all components, and the heat sink isn't visually accurate (but the external dimensions are correct)

You need to connect the Ender 5 plus hotbed wires to the nearby linear bearing. ...Adjust the height according to where you attach the wire, whether at the top or bottom of the bearing.

Heated bed control block found inside the Ender 5 Plus. ...Does not include all components, and the heat sink isn't visually accurate (but the external dimensions are correct)

Will need some sanding and epoxy. ... Epoxy the Air Director to the Air Director Cover. The "tall" version can be used to keep the wires off the bed (Ender 5 Plus)

A bracket that support a BTT TFT24 display inside the housig of a Creality Ender 5 Plus. Raplacement of Creality TFT touchscreen. ... Downside of this design can't use USB and SD-card slot

I took GenMatthius' innovative Dial Indicator Holder design and adapted it to perfectly fit the Ender 5 Plus fan housing, capitalizing on its versatility to deliver a customized solution for the community.

Remixed the clip from kbrouder to hold in the rails of the Ender 5 Plus a little better. 

Here's a custom foot I designed for the Ender 5 Plus, printed with Cura Slicer. ... If you find this helpful, consider donating an amount you deem fair via PayPal to help offset my time spent on the design.

Couvercle Magnétique pour Ender 5 Plus. Fini les mouches, moucherons, moustiques attirés la nuit par l'éclairage de l'écran. Une couvercle simple et efficace. Nécessite 4 aimants de 12x1mm... ...et un peu de colle.

Ender 5 plus 2.3kg spool holder. Works with 0.75kg and 2.3kg spools. 50mm Diameter 105mm Width Mirror 3DS1 for dual setup. ... Works with the original hardware from the standard spool holder (one in each holder)

Adapter bracket for an SKR 2. ... Made for Ender 5 Plus, could fit others. I used a SKR 2 but should fit 1.4, 1.3 also. ... Has wire tie down points at the bottom.

... pins, while five millimeter C'Bore holes enable secure fastening to 20mm extrusion. A thoughtful addition is a central hole for cable tie organization. We're thrilled you like this design and encourage you to print one for your Ender 5 Plus today!

Habe höhere Füße für den Ender 5 Plus konstruiert um einen besseren Luftfluss für die Kühlung zu gewährleisten. Sie sind ans Original gehalten, nur höher. Sie können eventuell auch an andere Ender Modelle passen, aber ich gebe keine Garantie. Nach...

Habe höhere Füße für den Ender 5 Plus konstruiert um einen besseren Luftfluss für die Kühlung zu gewährleisten. Sie sind ans Original gehalten, nur höher. Sie können eventuell auch an andere Ender Modelle passen, aber ich gebe keine Garantie. Nach...

Dial Indicator Mount designed for the stock fan shroud on the Ender 5 Plus. Print with the X flat on the build plate. Designed to print on the Ender 5+ without supports. If you have any ideas on how to improve this mount let me know in the...

This is an STL of the MicroSwiss Direct Drive Extruder plate for the Creality Ender 5 Plus. The STL was provided by MicroSwiss. ... I highly suggest buying it from them:...