ender 5 octoprint profile 3d models

Since there wasn't a BLTouch mount for the Ender-5, I remixed one for the CR-10 using Tinkercad. The model's quality isn't perfect, but it gets the job done just fine. All you need to do is add one washer per BLTouch screw and you're good to go. I'm...

I have a tool box that perfectly fits on my Ender 5 Pro printer, taking into account its maximum build volume to prevent the bed from hitting the top of the box. The inside measurements of the toolbox are approximately 100x220x35 mm. It's also...

Ender 5 is an amazing printer able to deliver very high quality but it needs some tuning. One of the things I did was to replace the bowden extruder by a cheap direct mod. It uses the same extruder stepper and metal extruder. Cable included was short...

My ender 5 kept hitting the carriages against the far x rail when I tried to set the bed size to 235 x 235 in Marlin. I found that the Y carriage was about 4mm short of the silver corner brackets on the far side when it hit the Y endstop. When I...

This case fits perfectly with the Ender 5 and is tailored specifically for use with an SKR V1.3 or MKS Gen L mainboard, making it ideal for my particular project of adding a heated build enclosure. To prevent hot air from accumulating inside, this...

This case is to suit the Ender 5 with an SKR V1.3 or MKS Gen L. It is specifically designed for my application of adding a heated build enclosure. Therefore, it draws and expels air from the underside edges of the printer to avoid the hot air inside....

Designing a glass enclosure using the frame on an Ender 5, I'm envisioning a 30" x 36" x .092" hardware store glass that will be expertly cut at every Home Depot and Lowes location. The design features main supports at each corner, along with strips...

I'm having issues with my Ender 5, as it keeps hitting the carriages against the far X rail when I try to set the bed size to 235 x 235 in Marlin. When I investigated further, I discovered that the Y carriage was roughly 4mm short of the silver...

This is a cover I made to clean up the cables on my Ender 5 Pro. Its made in 2 parts, the outer side (mount) which bolts to the extrusion using 4x M4 bolts and captive extrusion nuts. And an inner side (cover) that then slides over and bolts onto the...

The Ender 5 is a great printer, but the bed support could have been better designed as it is hanging down in the front. Didn't find a support that I liked, so I made one myself. The bolds and nuts are M6, but probably will also fit 1/4". I used self...

I struggled to find good Ender 5 BLTouch Mount. So i took the best one I found and made some modifications to it to make it stiffer and more secure. You use the two shroud screws and the top left wheel screw to hold it in place. I printed it...

Using 4.5mm thick acrylic panels for a simple enclosure mounted to the exterior of the extrusions of the Ender 5 plus using simple clips. I used M5 buttonhead bolts with T nuts and hex head bolts everywhere, just measure for the lengths required. ...

... of the Duet and mount the enclosure on the right bottom extrusion with some drop in (hammer) t-nuts and m5 screws (I used 8mm SHCS but there's nothing special about using SHCS). For more information: https://ender-5-mods.crpalmer.org/duet3d-upgrade

It started off as a pro, I should have gone with the standard Ender 5 :) ## Future Upgrades Linear Rails Mod * Printed in SunLu Carbon Fiber PLA * https://www.thingiverse.com/thing:3845704 * In-Progress ## 1/24/2020 * Link to my Marlin fork with my...

Struts to support the bed on the Ender 5 (or similar), to reduce vibrations and generally increase stability.Buy me a coffeeI wanted to combine the best bits of this and this design and here is the result. Fundamentally, it's the 'compressive'...

More info about clipper can be found at: https://github.com/KevinOConnor/klipper Design to convert your stock Ender 5 to COREXY with linear rails This design is in working phase, has been fully tested. Current model has Microswiss/Creality stock...

Ender Five Module Z Activated \r\n \r\n Lunar Operations Unit Number Ten Lambda Upsilon Universal

Shortened the mount base.

Remix from https://www.thingiverse.com/thing:4648289. I remove the switch hole and the grill and add a new grill for a 30mm fan (https://www.thingiverse.com/thing:2802474), what is connected to the RPI GPIO. ...Also I modify the LM2596 holders...

UPDATE 2019/08/04: Today I snapped my camera mount while tilting the printer, forgetting about attached parts that might stick out :-(. In case you've experienced something similar here it comes - the reinforced version! I hope that the modified...

Based on idea from: https://www.thingiverse.com/thing:2885049 Remixed between this https://www.thingiverse.com/thing:2873157 and this https://www.thingiverse.com/thing:2147179 I currently use Filament sensor simplified, please refer to this...

Designed to hold a rPi 4 against the rear plexiglass of the Ender6 by clipping into the rail. ... Provides a couple of choices for camera angle (I prefer the 55 degree version)

<p>hot tip.. ...you can gain 20mm in Z by moving the motor bracket underneath the profile

Stealthburner Mounting for Ender 3 and 5 After using the SteathySwiss mod for more than a year I had to reprint it after starting to print ABS parts in a enclosure as they started to warp because of the heat and that I printed them in PLA. As I...

... cut 2 cm off the tool mount and paired it with a modified GoPro mount, which works perfectly now. Meanwhile, I was reading about Octoprint and discovered that GoPros don't play well together, so in the end, I'll be adding a different camera instead.

I didn't like the appearance of the cables after attaching my camera to Octoprint, so I created these clamps to improve both looks and performance. I designed a slightly larger one to ensure easy cleaning of the OEM cables. Since they're a bit short,...

Creality Ender 5 extruder arm. This device repositions the extruder, allowing for a drastic shortening of the Bowden tube. By doing so, you can significantly reduce the retraction value and eliminate stringing problems. The printer is secured with...

Watch this video on YouTube to see a 3D printed pen holder made for Ender Printers, which can hold pens or pencils securely in place.

Ich möchte euch hier mein Kabelmanagement für den Ender 5 vorstellen. Ich habe nicht alle Teile selbst entwickelt sondern habe folgende Dateien für Mich angepasst: https://www.thingiverse.com/thing:3967562 https://www.thingiverse.com/thing:4116655...

This is used on the front right (or left) of my Ender 5+, but it will fit any 40mm extrusion. The model can be mirrored in your slicer to put the rear wing on whichever side you like. It will clear the bed in any orientation. I added three micro...