ender 5 linear rail upgrade 3d models

I also have a design that allows for a second linear rail to be mounted underneath the X-axis aluminum extrusion, so I may upload that if there is any interest. Also, you will need to trim the X-axis strut to 500mm. Parts List: 7x M5x50mm Machine...

Basic little end stopper 3mm screw hole for putting on a V Slot Rail. One of the mods I have made myself for my Ender 5 Plus Linear rail upgrade.

This mod mounts linear rails on the outside of the frame yeilding a bit more travel which pairs well with a bed upgrade. I prefer these heavy 15mm rails for the ender 5x to match the rest of the overbuilt machine. ... 2x MGN15C X 400mm 12x t nuts ...

This is a remox of my own design that can be found right here: https://www.thingiverse.com/thing:4272943 Since my last Ender 3 linerar rail upgrade kit released I've got a few questions about using other rails. This version is therefore made for the...

This is a complete set of parts to modify an Ender 5 to linear rails with silent endstops and an EZABL mount with cable strain relief. -------------------------------------------------------------------- 01/20/2020 Changed X axis mount, The...

... roundhead screws to secure the x-carriage hotend plate in place. This revised version builds upon the remix of SpeedDrive V1 - Ender 3 direct drive mount by sashalex007, tailored to fit the Ender 5 Linear Rails Mod created by KerseyFabrications.

This is a linear rail mount for the X axis of the Creality Ender 5 with a Micro Swiss Driect Drive kit. The linear rail used is a MGN12H, 300mm The advantages of this design vs the others are * You don't lose X/Y space * Compatible with HeroMe You...

To upgrade the Ender 5 Plus, you'll need to gather the following essential components: 1. Three 450mm MGN12H rails 2. Three MGN12H bearings 3. Sixty-six M3x8mm bolts 4. Sixty-six M3 T-Nuts The total cost for these parts will be approximately $120. I...

Ender 3 Linear Rail Upgrade video Upgrading the X-Axis to linear rail on your Ender 3 / Ender 3 Pro / Ender 3 V2 has never been simpler! Convert your Ender 3 to X-Axis linear rail in minutes. Bye Bye POM wheels! Get a smooth & precise motion + no...

This is a direct drive Orbiter V2.0 extruder paired with a collar mounted E3DV6 Revo hot end and linear rail upgrade for the Ender 3. It was remixed from this posting on Printables...

Video Guide: https://youtu.be/9o34FILD9Ng Needed: MGN12H Linear Rail 300mm (May Work With Other Options Too) 4 M5 Lock Nuts 4 M3 Lock Nuts 4 M5x12 Screws 4 M3x12 Screws 8 M3x8 Screws (4 for Sliding Block, 4+ for Rail Attachment) 4+ M3 T Nuts to...

To modify the Ender 5 Plus you will need the following: 3x 450mm MGN12H rails 3x MGN12H bearings 66x M3x8mm bolts 66x M3 T-Nuts All the above will cost about $120 or so. Print 2 of the Linear_Rail_Adapter_V3 For the X-Axis you will need M4 and M5...

When you get your aliexpress linear rails for your Ender 5 plus, you might get install blocks as pictured, luckily I did. Those install blocks are inadequate since they end up putting the X gantry far too high on the top 4020 channel. Drop the rails...

12mm x 300mm rails covers: use 4 pcs M4x25 + nut y rail adapter use 8 pcs M5x10 + nut and 8 pcs M3x10 installation: remove all rollers on the y travel 8pcs mount 12mmx300 linera rail incl the blocks measure 4.00mm from top of the frame 2020 profile...

I was getting increasingly frustrated trying to find a plate that would accommodate both my E3D Hemera and BLTouch, along with or without Linear Rails, which could fit onto my PrinterMods Direct Drive Plate. The PrinterMods Plate has holes for the...

My Ender 5 Plus has the Micro Swiss NG extruder and hotend so I took the parts from the one this is logged as a remix of and the Kersey Fabrications parts (https://www.thingiverse.com/thing:3646827). The Y rails go on the outside of the extrusions....

**This is a work in process - parts are usable in current state** Included parts to upgrade your Ender 3 Pro from the POM wheels to linear rails on the Y-Axis. No more adjusting eccentric nuts under your bed! Compatible with MGN12H Linear Rails The...

Y-travel 232mm with covers and silent end stop. 12mm x 300mm rails covers: use 4 pcs M4x25 + nut y rail adapter use 8 pcs M5x10 + nut and 8 pcs M3x10 installation: remove all rollers on the y travel 8pcs mount 12mmx300 linera rail incl the blocks...

This is a linear rail mod for the Ender 5 Plus. It encompasses the XY&amp;Z axis. I designed these parts because I was unhappy with most other mod variations of them.</p><p>Z Axis - The Z axis part were designed using the BLV MGN Cube as a starting...

This is a linear rail conversion for the Ender 5 Plus. It encompasses the XY&Z axis. I designed these parts because I was unhappy with most other mod variations of them. <b>Z Axis -</b> The Z axis parts were designed using the BLV MGN Cube as a...

I was looking around for a kit I could download and print that would allow me to install linear rails on my new Ender5 plus, but the only one's I found were for the CoreXY conversion or with Y rails mounted on the side of the frame instead of on top....

The Linear Rail Brackets from Ralp57 (https://www.thingiverse.com/thing:4487342) suggest what I felt was an unnecessarily complicated way to raise the Z screw and Z linear Rails. You need to raise the bed when fitting linear rails because the X...

The Linear Rail Brackets from Ralp57 (https://www.thingiverse.com/thing:4487342) suggest what I felt was an unnecessarily complicated way to raise the Z screw and Z linear Rails. You need to raise the bed when fitting linear rails because the X...

Linear-rails like this can be purchased on Amazon, for example: https://www.amazon.com/gp/product/B078M1GYV4/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1. A short video demonstrating the adapter is available at: https://youtu.be/d2JOcwX44N0. ...An...

For the Y linear rail adapter 4xM4x18mm and 8xM3x8mm For the X linear rail adapter 1xM5x12mm, 1xM5x8mm and 4xM3x8mm 2 x 350mm rails for the sides (Y axis) 1 x 300mm rail for the extruder (X axis) screws + mounting material for the linear rails...

A linear rail upgrade for the ender 3 that was designed to require as little aditional hardware as possible. There's no drilling, cutting or modifyning of the stock parts and all of the metal plates and brackets are still used. As well as the stock...

12mm x 300mm rails Covers: Use 4 pieces M4x25 + nut Y rail adapter use 8 pieces M5x10 + nut and 8 pieces M3x10 Installation: Remove all rollers on the y travel 8pcs Mount 12mmx300 linear rail including blocks Measure 4.00mm from top of the frame...

This is a remix, taken from two of Hangtight's designs, the one linked and this one https://www.thingiverse.com/thing:3241793 and modified to fit this bracket for top mounted linear rails:...

Was ask to post my design from :- https://www.reddit.com/r/ender5plus/comments/ljqbks/loving_the_hemera_on_the_ender_5/ They are a little overkill , but if it isn't broke don't fix it .

This is a test to convert the Y axis of my Ender 3 Pro to linear rail. For this, I used two MGN12H 300mm Linear Rails, some screws, and a small amount of ASA filament. To fit the linear rails correctly, I made a tool:...