ender 5 fan shroud 3d models

... should work without any issues. This print doesn't require any additional supports or screws; it simply uses standard Ender 5 parts. ...However, you may need to spend a bit of time adjusting it into place due to the relatively tight tolerances.

... ... Its remixed so it will fit the stock Ender 5.exept for the fan mounting. I've made it a little wider to fit the cables from the hot end and removed the ABL mounting. ...I've put the text Ender 5 on the inlet and made vent holes on the side.

MINIMAL is a new fan shroud for Ender 5 with several advantages compared to the original one. ...It weighs 6 times less, the cooling fan is a bit higher so it cools only the heat sink and not the heating block and the new layer fan duct works...

MINIMAL is a new fan shroud for Ender 5 with several advantages compared to the original one. It weighs 6 times less, the cooling fan is a bit higher so it cools only the heat sink and not the heating block and the new layer fan duct works...

MINIMAL is a cutting-edge fan shroud designed specifically for the Ender 5, boasting several significant advantages over its original counterpart. Weighing in at an impressive six times less, this sleek new design allows for more efficient airflow...

I got fed up with the lack of focus the stock fan shroud provided and the downdraft on the part print from it #FittyJippy 0.4mm Nozzle max

Adjusted in response to this reddit post: https://reddit.com/r/ender5/comments/uq9jjc/spider_hotend_shroud/ Remixed from: https://www.thingiverse.com/thing:5369808

I tried using the original design on my Ender 5+, but unfortunately, the tabs for the screws were slightly too thick. Printing it with resin proved to be a challenge as well - the logo required extensive support structures, which made the process...

I had some issues with the fan bracket being perpendicular to the nozzle, so I made four versions (0Deg, 2.5Deg, 5Deg, and 7.5Deg) where the mounting holes are angled to help pick the nozzle relief area up to a better angle with the nozzle. STL...

This fan shroud is designed to precisely fit an Ender 5 Plus with Spider Hot End using the HBE X Carriage (purchase on eBay). It allows the reuse of the factory fans. It is based on https://www.thingiverse.com/thing:5369808 and uses the plate that...

... and had to design a mount and fan shroud. ... This is for the Ender 5, though you may be able to design a much better set. https://youtu.be/CsgpFzxfca0 The fan shroud is heavily edited from Gabriel3DCaster: https://www.thingiverse.com/thing:2814127

I added an "adjustable BL-Touch mount" onto the fan shroud so it will fit on an Ender 5. I moved it 10mm to the front to clear the belt clip. I closed up the underside a bit and adjusted the air exhaust on the side. The offset i measured is: X:...

This part allows you to mount two 5015 fans on a Creality Ender 5, Ender 5 Pro, Ender 5 Max. I have not tested the Ender 3 or Ender 3 Pro, but I know that it doesn't work for the Ender 3 V2 due to a different location of some mounting holes. The...

This fan shroud is designed to specifically fit an Ender 5 Plus with Spider Hot End using the HBE X Carriage (purchase on eBay). It allows the reuse of the factory fans and BL Touch mount while providing clearance to the linear rail mounts. This...

Updated fan shroud FROM MBOT3D MANNY UPDATED

Compatible with Creality Ender 5 plus 3D printer, this part is made to optimize airflow for the nozzle cooling.

I removed the stock cooling fan from the motherboard area of my Ender 5 Plus and replaced it with an 80mm fan. This shroud allows it to sit at the side of the box and uses the existing slots on the side. Vastly improved cooling and much less noise...

I started thinking about the original fan shroud as soon as I unpacked my Ender 3 Pro and started printing. It worked good, but I thought it could be better. Then I started reviewing and printing other popular fan shroud designs and of tried printing...

It uses keepang v6 mount from aliex I designed this to avoid PLA heatcreep that was present when using of the shelf fan shrouds. Air is escaping freely to the right and no heat creep is present. ... Design is original apart from 5015 fan duct which i...

This is a remix of [Thomebau's](https://www.thingiverse.com/Thomebau) fan shroud. Because his fan cover is a bit larger than the original my previous [printed BLTouch mount](https://www.thingiverse.com/thing:4607774) didn't fit anymore. I remixed his...

This is designed to house a 40x40x20mm cooling fan on an Ender 5/5+ with the Micro Swiss Direct Drive kit. This shroud includes a BL Touch mount, and a parts cooling duct. The cooling duct is 5mm lower than stock as the DD kit lowers the hotend...

I found the standard cooling shroud on my Ender 5 Pro and Ender 5 Plus to be a little inadequate. I couldn't find a model on Thingiverse that seemed to match my printers, both of which have Microswiss direct drive extruders. ... This is a simple...

This version is for the Ender 5, 5015 radial fan. The main changes are the belts have been accommodated for by moving the fan up 10mm or so, addition to the fan moving up the duct has been lengthened to adjust. As well as V-slots to fit the fan...

I printed this https://www.thingiverse.com/thing:5393935 before I realized it was only for a CR-10 - the 4020 fan hits the E5+'s Y-axis wheels. Thankfully MicroSwiss published the STEP file, so I spent 3 days learning how to modify it with Fusion...

______________________________________________________________________ This is a part cooling and hotend fan duct for the Ender 5 and Ender 5 plus, however it may work on an Ender 3 or Ender 3 Pro. I wanted a fan shroud that improved part cooling...

Fan Shroud, Probe Brackets and Endstop Bracket STL files For Micro Swiss NG Extruder for Ender-5, Ender-5 Pro and Ender-5 Plus. Compatible with: SKU: M3202 (Standard V-Roller Edition) SKU: M3204 (Linear Rail Edition) Use support from...

remix of hangtights fantastic design. ...remixed the base so it fits the ender 5 plus. ...without this base the bl touch is not able to be mounted and the base plate wont fit the carriage.

I own a Creality Ender 5 Pro, modified with a Micro-Swiss direct drive and all metal hotend.I´ve tried several fan shrouds and all of them have had drawbacks that I couldn´t live with. The criteria for me has been. FOW, I want to see my nozzle and...

Ok redesigned and Final So having downloaded and printed several Hot end fan shrouds and used a Satsana version for a while, then customised that. Ive now designed one from the plate up. taken some little ideas from the ones ive used over the...