ender 5 dual z 3d models

Remix of 2 Thingiverse Designs 1: Kilroy01's Ender-5 Control Panel Back Cover https://www.thingiverse.com/thing:3353394 2: Wolfganghsu's Snap-on LCD Cover for Creality Ender-3/Ender-3s/Ender-3 Pro/Ender-5 https://www.thingiverse.com/thing:3670360...

Z shim for CTC printer for 6mm Glass bed

UPDATE 22/02/2023 :* Added an M5 version for z_bottom_left (as it was asked by a member)* Added my M3 & M5 printable T-nuts for help (print and insert std hex M3/M5 nut)---------------------I had hard times with banding on all my mini's (have...

Note: The adjustment for the Z-axis endstop was not included in the picture as it was added later. Print Settings: * Printer: OtterBot (my heavily converted K8200) * Rafts: No * Supports: Yes * Resolution: 0.2-0.3 * Infill: 20% or more Notes:...

This design draws heavily from the Dual Z axis upgrade by Caster, available at https://www.thingiverse.com/thing:2569379. Huge thanks to Caster for sharing this fantastic design! However, I had to create my own version due to a lack of required parts...

These are the components needed to upgrade the Nereus Dual Z.\r\nYou will also require two Leadscrews ( https://www.aliexpress.com/item/32818374370.html?spm=a2g0s.12269583.0.0.5e99663fMqOA8s Lead ) 8mm diameter and 600mm long.\r\nBearing 688ZZ...

Some parts I did for enhancing my Ender-5 Plus when doing the direct drive upgrade.Cable guideA fixation for the extruder cables. Needs a M3 x 6 counter sunk screw.Z-screw fixationThe Z-screw holders need four M4 * 10 countersunk screws and four...

Simple Ender 5 temp test. Remix from the ender 3 temp test. will include the Gcode with temp changes already done. ...Just load g code and print no slicing required

I scoured my workshop for a back cover that would fit my Ender 5 control panel, but all I could find were ones designed specifically for the Ender 3. The Ender 3 model looked promising, although it did print slightly off-center - perhaps this was due...

This is a complete Cable Chain / Drag Chain for thee Ender 5 You will need : 1 meter 19x10mm Chain - (I bought as sizing is perfect (you can also print) 1 meter 15x10mm Chain - (I bought as sizing is perfect (you can also print) 2 x spring washers...

... the Config.txt file, set equal current values for both drivers. For example, if you're using beta and delta settings: gamma_current 1.5 (Z Axis) epsilon_current 1.5 (Extruder E1) The attached config file is configured to use BLTouch and MKS TFT 2.8.

I think the most straightforward design for a single motor dual axis mod is needed since I'm working with aluminum parts, and I already have free acryle Z motor mounts and nut holders available. If you have them, the part list will be quite short: ...

redesign part posted on priintables.com. ...the extra strength should make the z-axis more stable

The bed no longer wobbles and we are back to full steam printing at 60+mm/sec like the Ender 5 cube design was intended for! ...I realize that not everyone would like to glue things to their printer and may want a bolt-on version, so I will be...

The user requires a dual end stop halter specifically designed for the Sidewinder X1. ...However, adjustments to the firmware are necessary prior to its installation.

... raise the gantry the stepper is armed and will then hold position. After this I home, PLA preheat and do a manual bed level. I utilize Lukes Firmware, so the Z align and the probing is done at the start of the print every time (about 4-5 minutes).

Ender 5 cooling system! Magnets 10 mm for fixing and two fans (Ultra Quiet XS1 50mm) connected as replacement for the normal cooler! ...It works fantastic!!!

Thanks to Print2Win for https://www.printables.com/model/116678-microswiss-ender-5-directdriveallmetalhotend-assem it was a lot of help getting the design together.

I maked a 12mm ABL Sensor Mount in Hotend Shroud for my Ender 5 3D printer. ...The Shroud is 3D printed.

This is a model I created of the Creality Ender 5 Plus. ...I use this to design add-on parts and enclosures.

These will replace the black end caps on your Ender 5 printer. ...I made mine with my initial, but the .STL I provided is blank.

Basic bed support for a Creality Ender 5. Requires an additional set of linear bearings, zip ties, and some M4 bolts+nuts. ... Installed: https://imgur.com/a/Ro59sVi

Cut a small hole in the BLTouch Mount designed by registeredthing to accommodate the Creality Ender 5 Extruder, leaving the belt attachment intact and untouched.

Enclosure for a Ender 5 Plus, work in progress, will update as I get more completed.Material is 2mm Aluminum, if needed I can upload the DXF flats.

This small lever secures itself onto the extruder of the Ender 5, allowing for manual control over filament feeding and retraction.

Thanks to Print2Win for https://www.printables.com/model/116678-microswiss-ender-5-directdriveallmetalhotend-assem it was a lot of help getting the design together.

Individuals appreciate the straightforward design of the Ender 5's extruder knob, making it easy to use even for beginners when printing simple objects.

If you're printing with a thicker bed or adjusted nozzle elevation, be sure to utilize Z-axis shims.

Remix of 3.5" HDD to Dual 2.5" HDD / SSD Bracket https://www.thingiverse.com/thing:3619679

22-4-18 4 files updated with bigger holes for LM8UU Z_Carriage_Body Z_Carriage_Clamp This is my version of Hypercube with a larger printing volume featuring two Z motors and leadscrews. ...The complete setup is located here:...