ender 5 dual z 3d models

Remix of the great Ender 5 Tool Holder to store your nozzles

Oldham's teeming tarantula and dual-zoned system.

Here are the specific parts I used: Note: Since I based my design on the factory Dual Z setup, a right side lead screw bracket wasn't necessary. ... T8 600mm 3D Printer Stainless Steel Lead Screw Coupling Shaft Mounting Bearing Link:...

Simple print that attaches to the top extrusion on the Ender to help with aligning dual z motors

This is the Z Hall endstop for Ender 5, or other. It's made for 2020 profile, and to rotate the plug on 90 degree. For reference see the pic. There are 2 M3 holes inside the case to screw the board, but it is actually not needed. All components...

Firmware (Marlin): configuration.h Set this true #define INVERT_Z_DIR true configuration_adv.h Uncomment the following #define Z_DUAL_STEPPER_DRIVERS The other brackets are here: https://www.thingiverse.com/thing:2377413 If you are using the...

I wanted dual Z screws with a single motor, and Supasorn's Tarantula solution was extremely simple and elegant. I remixed it to fit my Anet A2. The difference is that on the A2, the distance between the vertical frame and X bar is larger, so the...

I made these so I could use a larger z-axis stepper motor to fix the falling bed on my Ender 5. No extra hardware is required. ...Just remove the old feet with the hex key that comes with the printer and use the same bolt to attach the extended feet....

I made these so I could use a larger z-axis stepper motor to fix the falling bed on my Ender 5.No extra hardware is required. ...Just remove the old feet with the hex key that comes with the printer and use the same bolt to attach the extended feet.</p>

So I discovered my Anycubic i3 Dual not consistently homing because the Z endstop was sliding along the holes it's designed to be secured to. So I had 2 choices: Tighten the screws even more or print a suitable holder. In the instructions they even...

Simple Z-Endstop Mount Used for Dual Endstop Conversion of My Tronxy X5S. The switch is mounted to the holder using small, 2mm self-tapping screws. Update: I added two pictures of one mount installed. I chose this mounting method but feel free to...

Dear Cr10s 3D Printer Owners, I designed for Dual Z syncronize for my Cr10s Printer. Parts You need find below, 2 each Bearing Outer Diameter 22 mm Inner Bore Diameter 8 mm, Height 7mm Aliexpress many trader 3 each Pulley GT2 20 teeth for 6...

BOM printable: 1 x https://www.thingiverse.com/thing:181349 (horizontal belt tensioner) 1x Right belt guide.stl 1x motormount.stl 1x Z holder left.stl 1x Left belt guide.stl 1x frame mount+pulley BOM to buy:...

This is the Z Hall endstop for Ender 5, or other. It's designed specifically for a 2020 profile and rotates the plug on a 90-degree angle.\r\nFor reference, see the included picture.\r\nTwo M3 holes are located inside the case to secure the board,...

These modifications are designed to convert the Tevo Tarantula Dual Z axis from a single motor setup. Complicated trade-offs are omitted here. No more motor couplers will be needed, simplifying things significantly. This setup is slightly trickier...

The precise replica of the Creality Ender 5/5 Pro/ 5 Plus X carriage, meticulously crafted to mirror its original form and function with unwavering accuracy.

Dual Z lock for the CR10-500. I've encountered some problems where the two sides get out of alignment, so I investigated possible solutions and found that a GT2 1220mm closed belt and two 50-tooth GT2 pulleys fit perfectly. They fit well under my...

This will function with any CR-10 that has dual Z-Axis, but it will require a smaller belt. The 50 teeth pulleys provide more torque, which is why I prefer them. I added an idler to pull the belt away from the front of the tension as the original...

I've been upgrading my dual stepper setup by swapping out the old z-axis assembly with a new one. The new design is based on this thing: https://www.thingiverse.com/thing:2334406/files, but since I'm using a thicker x-rail system, which is actually...

This is a remix of bitbrain's Tevo Tarantula Dual Stepper Inverted Z brackets. So first of all thanks to him for his nice design. There were a few things that bothered me though so I decided to make some quick modifications. #### Changes: * The...

It will be a tight fit (to stop it sliding down the extrusion) Check out my other designs for the Ender 5: - Top mount spool holder: https://www.thingiverse.com/thing:4368026 - LED Light Bar: https://www.thingiverse.com/thing:4306508 - Rpi Camera...

Dual Z lock for the CR10-500 I have had some issues with the two sides getting out of alignment so I looked at the possibilities and one GT2 1220mm closed belt and two 50 teeth GT2 pulleys fit perfectly. They fit well under my frame braces and It...

For firmware settings (Marlin), you'll need to make the following adjustments: configuration.h: Set this parameter true #define INVERT_Z_DIR true configuration_adv.h: Uncomment these lines #define Z_DUAL_STEPPER_DRIVERS You can also use these other...

This is an original design for the Ender 5 LCD mount. ...Frustrated with scouring online for a reliable Ender 5 model, I decided to save time by creating my own.

Ender 5 rear power cable clip. ...I crafted a straightforward clip to attach to the backside frame of my Ender 5 Pro, securing two wires while allowing for easy removal by sliding it upwards.

Creality Ender 5 Plus model. ...Currently a work in progress and will be updated as I work on it Many parts derived from this model: https://grabcad.com/library/creality-ender-5-pro-1 Last updated 8/10/20

Had to change fan and wanted to add a personal touch to the Ender 5 S1 Hotend Cover by MakerMason3D.

A tool clip which fits to the Ender 5 profile, holding every tool which is delivered along the printer itself.

Managed to tweak it enough to make it compatible with my Ender 5 setup. ...Greatly appreciate your assistance, AlexWaveDiver!

I redesigned the legs of the Creality Ender 5 printer to be larger and leave more space on the bottom.