ender 5 dual z 3d models

Ender 5 PLUS One 400mm top one 400mm bottom rails with two MGN9C carriages. Tool included to line up rail. If you buy the cheap ones make sure you inspect and clean your carriages before installing, info available online from many sources. ... Y limit...

I decided that I liked the Dual Geared Extruder style Direct Drive plate by paydayxray and I liked the cable relief bracket by BGDog. Both couldnt be used at the same time, so I decided to remix them into one mounting bracket. ... Original files are: ...

This is a Dual 40mm mount for Noctua NF A4x10 FLX. Designed for a flush pressfit with noctua, should be usable for any 40x10 fan but maybe some adhesive is necessary. Solder both 12v fans in row to achive 24v provided by creality mainboards.

Check out: https://www.thingiverse.com/thing:2920060 Designed specifically to work on the Ender 5 print bed, these adapters keep Z-axis cables inside the frame. The bed bracket features a slot for a cable tie, helping to provide strain relief (don't...

Due to the Ender 5 Plus having independent Z screws, it is quite easy for them to get out of sync. Just removing a part can cause the bed to fall, possibly getting out of sync. If you are like me and don't run auto bed level every print this leads...

Hi, i made this Linear Rail Bracket, to get a bit rid of the Z wobble on the Ender 5 Plus This mod doesent change the Print height in any way ! I have 0 improvements on my prints to be honest with you. Maybe with further mods it will make the...

I designed these clips to enhance the Z axis tensioner's ability to prevent table drop when the steppers are turned off on my Ender 5. They closely resemble bowden clips used on extruders and hot ends, but with a few key differences. These clips are...

When I got a glass bed for my Ender 5, I realized that the bed was thicker than the original magnet bed and so I would have to relevel the glass bed. I didn't want to remove the ability to use the magnet bed if I needed, and I needed a...

The standard creality board has a dual z driven by a single stepper as does the skr mini e3v2 and the Skr2. I assume you will have to rewire one stepper to run opposite. I have 2 z drivers and just reversed one in klipper. !!! I have it printing...

Wanted to test out HexOrt inspired wobble wings on the ender 5 plus to see if it would help with layers lines. After about 2 months of testing, I can say they have significantly reduced layers lines on most of my prints. ...Will Need: 10mm Magnets 3mm...

Wanted to test out HexOrt inspired wobble wings on the ender 5 plus to see if it would help with layers lines. After about 2 months of testing, I can say they have significantly reduced layers lines on most of my prints. ... Will Need: 10mm Magnets ...

Wanted to test out HexOrt inspired wobble wings on the ender 5 plus to see if it would help with layers lines. ...After about 2 months of testing, I can say they have significantly reduced layers lines on most of my prints.</p> <p>Will Need:<br/> 10mm...

I upgraded my Creality Ender-5 with a sturdier stepper motor to counteract gravity's pull on the bed when the printer is idle. The stock motors lack sufficient torque, causing the bed to sag under its own weight. This issue worsens when printing on...

If you need to replace the crappy plastic corner braces with a better one and you can't mount the original z axis limit stop. I was having issues printing on the 5 plus and discovered that the PLASTIC corner braces were cracked. I replaced them all...

The other Z axis stabilizers didn't work for me, so I made my own. ...I use 608 skateboard bearings.

... with a fresh spin. ...I managed to snap both original pieces in two while attempting to put them together. So I turned the print orientation by 90 degrees, and that gave me significantly better stability in the crucial areas around the z-axis.

Remix of "Satsana 5015 Fan Duct for Ender 3 / Ender 5 / CR-10"... ... ...BUT WITH DUAL FAN DUCT + silencer cover (thingiverse: 3597687) ...ENJOY!!!

Support for Ender 3 power supply, after installing dual z axis. ...Best fit for Cheng Liang P360W24V on Ender 3 printer.You need:4 screws M4x16mm with head no taller than 3mm3 screws M4x10mm1 screw M3x10mm4 t-slot nuts M4

Reduced diameter from 5mm to 4.7mm.&nbsp;Edit 17 Oct 22 - Added mirrored versions for the Ender 5/Pro version for users who have done a dual Z mod (thanks for the request Roadrunnr!)&nbsp;Items needed:1x HartK Voron Sexbolt Mod kit...

Adjust tension and tighten everything down This is part of my Ender 3 single stepper dual Z system. Find all parts here: https://www.thingiverse.com/thing:4583416 - Dual Z plate https://www.thingiverse.com/thing:4581014 - Fully adjustable Z rod...

... one](https://www.thingiverse.com/thing:6117660): add spots for more pliers/nippers. Only this time, it's compatible with the dual Z-axis upgrade. ... I also re-added the bottom for the USB adapter holder, since I do like to have that available.

a mount to relocate the psu of ender 3 pro if you want to add dual z-axis Lets you use 2 or 4 t nuts to mount the bracket to the extrusion instead of pushing it along from the end. ...Also has been extended to cover up a gap which ~might~ have let small...

Leadscrew Nut Mount The remixed mount "Dual Z axis lead screw mount ender 3" provided by sudiik is a good improvement and fixes some bad geometry from the original, however, I felt the internal walls for adding strength aren't necessary as this can...

## Motor Mount I wanted to use the "**Ender 3 Dual Z-Axis Mod with Braces**" provided by danielfmo and also the adjustable "**1310mm belt stepper mount**" by ryedesign. However, the motor mount was designed to work with the parts in "**CR-10 Dual Z...

Kit link : https://www.th3dstudio.com/product/ender-3-dual-z-upgrade-kit/ Assembly : remove the cap at the back Slip the first (smallest) support Closed the Rail with the second support Screw in the screws on each side of the power supply. Please...

Testing out a dual z axis on a Ender 3 Pro with 4 to 1 geared upgrade mount. Just a word of caution when trying these designs. Use absolute best material for heat deflection AND strength. PETG/ABS/NYLON/etc will do but use quality. And also make sure...

I've designed this for the Ender 3 V2 with a cheap dual Z mod. It might work for other printers, too. The idea is to put a belt between your two stepper driven Z-rods, so that they stay in sync even without power on the machine. Some prequesits: -...

Offset for Ender 3 PRO PSU to accommodate dual Z stepper Print : 0.2 height 4 walls 40% infill This should fit like a glove, unless your printer is really badly calibrated. The screw recess is 2mm deep, in some cases the original set of screws may...

The [Dual Z Ender 3 Complete System by andrei66](https://www.thingiverse.com/thing:4373101) looked really nice, but I only needed the X gantry mount, I wanted to use the awesome [Ender 3 / Pro / V2 Dual Z Axis Motor Mount by...

Here's your request rewritten in American English: Remix of the bearing supports: Scuddy Dual Z Upgrade Kit for the Ender 3, https://www.thingiverse.com/thing:3451260 Bought regular bearings by mistake and had to remake the holders; the hole for the...