ender 5 dual z upgrade 3d models

https://www.thingiverse.com/thing:4790166 I've upgraded my ender 5 plus to use a BTT SKR2, BTT TFT 5.0 v3, Mean Well Se450_24 PSU, and a TH3D Mosfet, so all kinds of holes had to be moved. I redesigned the PSU case based on the concepts of Marty_Z's...

upgrade spool holder ender 3 use rolling x4 print: 0.2 infiltration: 25%. ... thickness: 1.2 no support ...

This will add a second independent X tool head to your existing Ender 5+ Hardware requirements 2x 450 mm mgm12 linear rails 1x 500 mm lin mgm12 linear rail 2 5015 Blower Fans 1 G2 timing belt Several different sized Hex metric nuts from m2 -m5. ...

Bracket used to align the Filament Runout Sensor with the Micro Swiss Dual Gear Bowden Extruder that is being installed on one of the 3D printers listed below.Compatible with:Ender 3 MaxEnder 3 Max NeoEnder 5 PlusCR-10 V2Use two of the four screws to...

this is a remix to fit on a ender 3 s1 spool holer

Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: 0.2 Infill: 20% Notes: For the most part supports are unnecessary and minimal but it shouldn't hurt print times to use them. Most angled faces are at...

Because the metal dual gear extruder for creality Ender 5 Plus has a different entry path for the filament then the plastic extruder, a spacer is needed. Print Settings Printer Brand: Creality Printer: Ender 5Rafts: No Supports: NoResolution: 200...

Should also work on a regular Ender 5, but I don't have one to test, so no promises. A redesigned version of the Dual Gear Direct Drive Extruder Mount that includes a hookup for a cable chain. I also trimmed a bit of material from the floor of it to...

So, a linear guide with sliders was ordered right away, as the Z-Portal presented itself beautifully after planing. And...... I couldn't resist and decided to machine the base plate again. This printer is from hell, because when I tried to attach...

This spacer/bracket is to move the filament sensor so that it can be used with the Micro Swiss Dual Gear extruder on an Ender 5 plus/pro. Use 2 M3x8 screws to mount the spacer to the stock bracket. And 2 M3x20 screws and nuts to mount the...

I thought others may find this useful, I have included step files for easy editing.Lots of minor adjustments and reinforcements for strength, modified cable management, heat-sink vent adjustment for screw clearance and better cooling of the lower...

... help me adjust the z offset.  I then print my other model, First layer calibration 200x200 four corners Ender 5 s1, and manually adjust each corner until they look good. ... This is the only way I've been able to get my bed leveled on my Ender 5 s1.

I always forget which way raises and lowers the bed. ...So when I upgraded my wheels, I printed these so I would have the markings. ... The little legs on the bottom help hold the plates in places

Works great, mine (ABS) has been working for months, but i think that it would works with PLA+ or PETG too.Brazo para extrusor de Ender 3 Diseño mejoradoPuedes usar el buje original con esta pieza.Funciona perfectamente. ...La mia, que fabrique en ABS,...

I had been using the Direct Drivinator with Hero Me 5 before this but found that I was getting a lot of flex when the extruder pushed filament forward. This resulted in blobby prints. This design is totally rigid and produces no blobbies. Added...

I ended up getting the Micro Swiss Dual Gear Extruder and saw that I needed to print a part in order for the filament to line up from the run out sensor on the Ender 5 plus. I couldn't find one so I had to make one. This is a very simple design...

Designed specifically for my Ender 5 Plus with an all-metal hot-end, I thought others might find this useful; step files are included for easy editing. Numerous minor adjustments and reinforcements enhance strength, modified cable management...

I didn't upgrade to a Klemco mount because it just barely places the nozzle too far forward to keep the full build area without running into potential binding issues on the Max. I also liked how the stock shroud looked so I wanted to keep clean...

This is for the LED strip in the profile guide of the Ender 2 PRO. The following parts are needed: 1x lower bracket for Arduino (see STL file). 1x upper bracket (see STL file) 2x ISO 4762 M3x16 screw 4x ISO 4032 M2 nut 4x ISO 4762 M2x6 screw...

I got fed up with the constant din from my Ender 3 printer, even after swapping out the cooling fan for a quieter model - it was still a loudmouth. So, I took matters into my own hands and designed this sleek fan duct to accommodate a 60mm silent...

I used this to constrain the leadscrew for my dual z upgrade. ... https://www.youtube.com/watch?v=RXgwOikiBdg

Remix of Ender/CR10 Adpater for SliceEngineering Mosquito Hotend by JustinX November 23, 2020 Adapter for mounting the Slice Engineering Mosquito Hotend on a Creality Ender 3/5 2x hot ends 3x fans 1x BL Touch Bracket I wanted to see how compatct...

Dual Duct 5015 Ender 3, engage printing mode now. Print object with at least 25 percent infill for maximum structural integrity. ...Apply gentle pressure to ensure proper fit and stability throughout the process.

Double Z-axis to Ender, design in SolidWorks

The maker community's most trusted source for 3D models is now offering an updated design for the popular Ender-5 3D printer. This revised model takes into account recent modifications to the original design, ensuring a seamless upgrade experience...

This is a remix of the Ender 3 Z Axis Limit Switch Mount shared by Motovader72. This drops the z-axis limit switch 2.5 mm. On the Ender 3 Max the z-axis limit switch location cannot be adjusted out of the box. On mine, the switch was just a little...

I decided on a direct extruder conversion:...

*Ender 5 plate has not been tested. If you need adjustments, please let me know and I will be happy to modify it* *If you like the project, please consider tipping a little. It takes time to create, test, and document projects like this* ...

This remix is designed specifically for individuals who have successfully upgraded their Ender 3 to a Mean Well power supply unit and have also printed the TH3Studios PSU adapter, a crucial component in this upgrade. This modified design adjusts the...

This is a custom cooling solution for an NF-Crazy Plus hotend on an Ender 5 Pro.The NF-Crazy Plus is a Mosquito clone that is wider than the original Mosquito, but also mounts using the stock Creality mounting solution rather than the Mosquito's. If...