ender 5 direct drive 3d models

THIS REPLACES THE 3MM PLATE THAT NORMALLY GOES BEHIND THE DIRECT DRIVE GEAR ASSEMBLY AND ADDS A SUPPORT FOR THE BODEN TUBE AND SUPPORT FOR THE CABLES. ...ALL YOU NEED ARE SMALL ZIP TIES

The original fan shroud causes a loss of X travel on left and right side that I couldn't live with. So I narrowed it, moving the Pinda probe mount inside the fan shroud. The Pinda probe will screw into the hole allowing you to make fine...

... ... Additional option for the Ender 5 linear rail conversion kit here: https://www.thingiverse.com/thing:3782865 191111: direct-drive extruder mount final version 191111: Direct-Drive-Extruder-Mount Final Version 191124: Direct Drive Tube Mount added

This is my remix of the hydra fan duct to fit the MicroSwiss Direct Drive Kit for Ender 5/plus. Everything should work. ... Offset X= -1 Y= -40

This is my remix of the hydra fan duct to fit the MicroSwiss Direct Drive Kit for Ender 5/plus. Everything should work. ... Offset X= -1 Y= -40

Additional option for the Ender 5 linear rail conversion kit can be found here: https://www.thingiverse.com/thing:3782865 Direct-Drive Extruder Mount final version was announced on November 11, 1911. A new version of the Direct-Drive-Extruder-Mount...

A custom bracket designed to securely house the stock Ender 5 Plus filament sensor following a direct drive upgrade, also incorporating a built-in filament dust filter assembly for enhanced print quality and reduced maintenance. ... The mounting arm...

Fang base plate for the Micro Swiss Direct Drive + MS Hot End (Ender 5 Version). Use the following "fang"-duct: https://www.thingiverse.com/thing:4389912 ...and for the 40mm fan: https://www.thingiverse.com/thing:2763931 Offsets: x: -54 ...

It is for the ENOMAKER Direct Drive Extruder Ender 5 Conversion Kit and just replace the motor space with the printed part, install the QD for the tube, the other end of the tube goes to the QD on the filemt guide that just bolts to the holes of...

I purchased a direct drive kit and swiftly discovered that the spool holder base needed to be positioned on top of my Ender 5 printer. When I attempted to relocate the spool holder base, there was insufficient clearance for the printer head with the...

The one that he made works with the stock Ender 5, but recently I upgraded to a Micro Swiss direct drive extruder. The mount that he designed hits the spot where the belt is attached to the carriage plate. The mount doesn't hit the belt clip now...

24/12/20 A remix to hold a ptfe tube for a direct drive, seems to be useless and i already change spool position for a better performance i were getting some isues with cable management and as a result i changed it. ... changing the design for an...

This is a REMIX/COMBINATION of [Micro Swiss Direct Drive EZOut v2 Mount](https://www.thingiverse.com/thing:4232736) [Ender 5 Plus Linear Rail Conversion](https://www.thingiverse.com/thing:4578889) [Ender Filament Runout...

Specific to those that have Unitak Direct Drive set up on theyre Ender Printer This cover fits nicely over the ugly motor!

Smooth Fang Mounting Plate - Ender 5 Plus - Micro Swiss Direct Drive - BLTouch - ExoSlide BLTouch Approximate Offsets = X-44.6, Y-6.6 Ender 5 Plus (with BLTouch probe), using a Micro Swiss Direct Drive extruder kit, mounted to an ExoSlide linear...

I tried looking for parts to add a 10x20mm cable chain to my Ender 5 Pro with a Micro Swiss Direct Drive Extruder with the Exoslide Linear Slide Kit. Here is the 10x20mm Cable Chain I used, https://a.co/d/iSzwFDn There are little rectangular...

I took the base and gantry adapter for the Micro Swiss direct drive Ender 5 plus and remixed it to be magnetically attached. ...I'm sure it's not perfect, but it works great for me.</p><p>Link to the magnets I used:&nbsp;</p><p><a...

Hotend and part cooling fan for the MicroSwiss Direct Drive. It is tight in the X direction but you wont loose any build volume, Y is at 46mm not larger than stock. BL-Touch location: X: +8mm Y: -23mm Stuff needed 2x 50x50x15 Fans 6x M3x5 (if you...

This is a simple adapter that enables you to connect a Mosaic Palette 2 directly to a Creality printer after upgrading with a microswiss direct drive upgrade. Instead of relying on the included velcro adapter, you can easily swap or remove your feed...

Hotend and part cooling fan for the MicroSwiss Direct Drive. It is tight in the X direction but you wont loose any build volume, Y is at 46mm not larger than stock. ... BL-Touch location: X: +8mm Y: -23mm Stuff needed * 2x 50x50x15 Fans * 6x...

Hotend and part cooling fan for the MicroSwiss Direct Drive. It is tight in the X direction but you wont loose any build volume, Y is at 46mm not larger than stock. ... BL-Touch location:X: +8mmY: -23mm Stuff needed 2x 50x50x15 Fans 6x M3x5 (if you...

When using Micro Swiss Direct Drive the hotend needs to stay where it is so I combined the base with the gantry adapter similar to what was done with the model I'm remixing, but here I have included the BLTouch mount. This is also done in a way so I...

I redesigned [this](https://www.thingiverse.com/thing:4810011) linear rail setup to accept an orbiter 1.5 extruder because I didn't like the rail on the back. ...Now it doesn't have to fight gravity!

This is a custom upgrade combining the Bondtech BMG print head and kmxs' Ender 5 linear rails, offering two options: Creality or MicroSwiss hot ends, as well as the e3D V6 hot end. Key Features: * The BLTouch probe mount is currently included, with...

Here's a re-designed direct drive mount, compatible with Exoslide linear rail products on the Ender 5/5+. Originally made of PLA, this design was prone to bending and deformation due to heat and weight. To counteract these issues, I've added extra...

The bracket that's included with the Micro Swiss Direct Drive Extruder for Creality Ender 5.

Ender 5 Plus X axis Linear rail with a BMG direct drive. ... Made using Ender 5 plus linear rail modification from: https://www.thingiverse.com/thing:3960105 and added a BMG direct drive and a cable management on the side. ...

A mount for the BigTreeTech Filament Smart Sensor for direct drive conversion kits that use the stock (or compatible) extruder of the Ender 5. It should work the same for the Ender 5 Pro and Ender 5 Plus. I guess It will work for an Ender 3 too if...