ender 5 direct drive 3d models

To download all project click in this link https://www.thingiverse.com/thing:5254723/zip Ender 3 Ender 5 Direct Drive Orbiter extruder V6 ================================ Lista de materiales: -------------------------- • 1unidad – Orbiter Extruder...

Ender 3 Ender 5 Direct Drive Orbiter extruder V6 Material list:1unit – Orbiter Extruder 1.5 RightFysetc Trianglelab 1 unit - Hotend V6 60-70 mm -- PTFE Capricorn 1 unit – Termistor ATC Semitec 104GT 1 unit – 40W Heater...

The mounting adapter slides over the wheel spacer post on the Micro Swiss Ender 5 direct drive plate and also slides into the belt slot and is secured to the Micro Swiss Ender 5 bracket with an M3x6 screw which is recessed into the back (you may want...

The mounting adapter slides over the wheel spacer post on the Micro Swiss Ender 5 direct drive plate and also slides into the belt slot and is secured to the Micro Swiss Ender 5 bracket with an M3x6 screw which is recessed into the back (you may want...

I wanted to give the E5DD(Ender 5 Direct Drive) bracket a try by @modrows1 as an alternative to that kit, but I also made sure I had a cable strain relief(https://www.thingiverse.com/thing:3591391/) in place. Since I couldn't use both at the same...

... the 42 stepper motor was acquired. 3.5 - Various 3mm screws were purchased (a comprehensive list will be provided later). 3.6 - The Swiss CR10 Hotend from Trianglelab was obtained, compatible with the stock hotend on the Hero Plus ver6 funduct.

Decided to try going Direct Drive with an upgraded extruder. Ended up with Titan extruder and no way to mount it. Found a mount here https://www.thingiverse.com/thing:4222781 It was working, but I felt that it needed to be a bit more rugged. I...

A remix of this direct drive solution for the Creality Ender 5: https://www.thingiverse.com/thing:4102545 The original design did not allow for the instalation of a Bondtech BMG dual geared extruder. This part should clear enough space for it,...

Decided to try going Direct Drive with an upgraded extruder. Ended up with Titan extruder and no way to mount it. Found a mount here https://www.thingiverse.com/thing:4222781 It was working, but I felt that it needed to be a bit more rugged. Added a...

Direct drive combines with Petsfang for optimized cooling, and an optional drag chain, BL touch, both, or just the Petsfang bullseye. Stock fans/hardware are used beside additional 4 twelve-millimeter M3 bolts to mount the stepper to the thicker...

Mount for the bl touch on a microswiss direct drive upgrade with hero me gen5.

This is a direct drive conversion for the Ender 5, Pro and Plus, using the stock hotend and extruder assembly. The part cooling relies on a superior 5015 blower, outperforming the stock part cooling blower in every way. The duct and outlet nozzles...

This is a direct drive conversion for the Ender 5, Pro and Plus, using the stock hotend and extruder assembly. The part cooling uses a 5015 blower for its far superior performance compared to the stock part cooling blower. The duct and outlet...

This is a direct drive conversion for the Ender 5, Pro and Plus, using the stock hotend and extruder assembly. The part cooling uses a 5015 blower for its far superior performance compared to the stock part cooling blower. The duct and outlet...

Remixed from https://www.thingiverse.com/thing:3872001 Added more legs for stability. ... Added threading for M10 and M6 bowden couplers because Ender 5 kits contain an extra M6 bowden coupler and also to remove requirement for a nut.

I decided that I liked the Dual Geared Extruder style Direct Drive plate by paydayxray and I liked the cable relief bracket by BGDog. Both couldnt be used at the same time, so I decided to remix them into one mounting bracket. ... Original files are: ...

Not satisfied with the included wire supports in the Printermods direct drive kit or the plastic Creality tower over the X axis mtr., designed these two brackets to function as replacement. ...Bracket located adjacent to extruder mtr uses 3 X 10 mm...

The original I remixed didn't quite fit my direct drive extruder, and I wanted it open on the front to aid feeding filament. This remix checks all the boxes I needed. I cut down the cable guide on the side a bit so that it would fit my extruder...

I also make the cooling fan work with the stock ender 5 fan ( it is pressure fit (no screws)) I also removed a "clip on" from the back of the unit as it is not needed when the device is seated. I left the top of the clip as a line up point and...

I also make the cooling fan work with the stock ender 5 fan ( it is pressure fit (no screws)) I also removed a "clip on" from the back of the unit as it is not needed when the device is seated. I left the top of the clip as a line up point and...

For the assembly, I used the original detector's screws of the Ender 5. Be careful, the holes are deliberately narrow, so you have to use an M3 tap, otherwise you have to pass once an original screw "in force" to create the tapping allowing the...

Can be direct drive or bowden. Converts hotend fan to 40x20 or keep 40x10 ( 40x10 fans are awful) Converts print fan to 50x15. Easy removal of extruder, easy removal of fans all without removing or disturbing the BLtouch. I strongly advise using...

It was time for drastic measures, so I decided to overhaul my direct drive filament guide and give it a stylish makeover. I added feet and a slot for an end-of/broken filament sensor to the mix. With the new front feet in place, the block attachment...

Pause at around 121.8mm or just before bridging starts over the hole for the M4 nuts, insert 2 of these. ...I'm using 16mm M4 bolts to secure the original spool holder to the extender.

First off, huge thanks go out to Ross K for creating this in the first place! I built upon his original design by adding a few extra features that I've been experimenting with while working on my printer projects. My hope is that someone finds it...

Remix of [Ender 5 Direct Drive Strain Relief (Enomaker)](https://www.thingiverse.com/thing:4407360) to fit the [ENOMAKER Direct Drive Extruder](https://www.amazon.com/gp/product/B08399KX3X/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1) The...

... by MicroSwiss. I highly suggest buying it from them: https://store.micro-swiss.com/products/micro-swiss-direct-drive-extruder-for-creality-ender-5 I am using the STL to design a cooling shroud since there are extra mounting holes on the plate.

Direct Drive Setup Guide: Securing Filament on Your Ender 5 Get a solid grip on your filament with our simple direct drive setup for the Ender 5. This guide shows you how to keep the filament in its original position. For the Single Bolt Version,...

I upgraded my Ender 5 Pro to direct drive and was in need of a filament guide for the top-rear-left mounted spool. The new guide is 20mm wide, secured with M3's and T-Nuts. It's set at 45 degrees to avoid any sharp bends when the filament is centered...

hello everyone this is a kit for convert your ender 5 plus to drect drive.so you can print tpu filaments with no problem