ender 5 cooling duct 3d models

... 3D printers. Including the CR10, Ender 2, Ender 5 ect... This is because it attaches to the same place as the hotend and does not rely on any other bolt holes. ... It fits with this BL touch mount, https://www.thingiverse.com/thing:4462870

I remixed one the original models for the 4010 fan for the Ender-6 as the cooling ducts were not central on the mosquito hotend, once duct two ducts were close but the third was offset by quite a way. This one better suits the Ender-6 with a BondTech...

MINIMALIST SILENT HOTEND COOLING DUCT FOR ENDER 3 V2 ==================== This is my take on a minimalist silent hotend cooling duct with integrated parts cooling fan. __Parts needed:__ --------------------- - 50x50x10mm fan - 5015 radial fan - two...

This thing has the original Solidworks Assembly file, where you can also find the ender 5 carriage, both hotends, and some previous versions of the desing. The assemly was simulated with CFD and temperature analysis, to be able to withstand at least...

The print utilizes the stock fan screws to hold onto the Ender 3's stock hotend fan shroud, and this fan duct makes use of both the stock screws and the hot end shroud on the Ender 3. Therefore, major upgrades aren't required; you just need to swap...

HevACS type of ducting works quite well when the hot-end is not moving in the Z-direction, which is not the case for Ender 3 and most other Cartesian printers. So I need to attached the outlet or the whole fan/duct assembly to the X-extrusion. After...

V3 changes: Thicker walls and thicker BLTouch mount Hello, I've made this because I want better cooling for my spider hotend as I think this duct will be better than the original cooler. It should also fit the Ender 3 and so on, but i've designed it...

Instead of adding more fans on the printer head where it adds weight and make it sometimes ugly huge to be effective, this puts the blower on the side of the X axis beam and so it isn't putting any more weight on bad places while still adding much...

remixed for ender 5 plus with microswiss direct drive kit. notch added to clear belt mounting. ...slightly larger clearance hole for microswiss plate mounting.

Great-looking part cooling duct, secured with a clip to keep the fan wires in place. Printing flawlessly and all credit goes to Rocco81-92 for designing an excellent system. Visit https://www.thingiverse.com/thing:2751027 for the hotend duct and...

This is a custom made Creality Ender 5 Plus complete bottom cooling case for ultimate cooling at half the noise. This uses 2 12v, near silent 60mm fans from RS components (RS Part number: - 696-3544) and 2 12v Noctua 40mm fans (NF-A4X20). Link...

Im currently designing my own printer from scratch mainly for speed but on the cheep, so took the idea using an Ender 3 but made for pure speed hence the name "Bed Slinger" trying to keep the hotend lightweight as possible i made this part cooling...

I required an effective means of mounting the standard part cooling fan following the upgrade of the hotend extruder fan duct to this: https://www.thingiverse.com/thing:2160958. This new setup offers significantly increased visibility and is...

Remix from wheelwrench adding a guard below the part cooling fan and beefing up the top layer that touches the silicon cover. ... Printed at 200c with build plate temp of 60c with my Modded Ender 3 Pro.

This is probably one of my favorite version of a duct for the ender 3, decided to add it on here to help those who may find it helpful.[Originally Uploaded by: KingYS on Thingiverse][Original Description]Print Settings:100 % infillstandard 0.2mmABS,...

remixed for ender 5 plus with microswiss direct drive kit. notch added to clear belt mounting. slightly larger clearance hole for microswiss plate mounting. ...Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution:...

Fits Satsana duct perfectly with stock Ender 3 hotend fan. You will need 4x 3/4 inch screws for construction. I used Machine screws found at a local hardware store that were #6-32 x 3/4 inch. They are slighly bigger than the stock M3 screws so use at...

i modified these two parts to fit perfectly together in the ender 3 v2 neo i added a little bump to keep the fan a bit away from the shroud, and removed the creality logo, if you want to use the default bolts, you put a bit of hot glue in the fan...

There are slight improvements on the bottom of the split in the Y and X.I'm planning a V2 to reduce the footprint of the duct as well as another Noctua cooling solution to cool the heatsink ( its very tricky/impossible with an axial flow fan)A note...

I'm planning a V2 to reduce the footprint of the duct as well as another Noctua cooling solution to cool the heatsink ( its very tricky/impossible with an axial flow fan) A note to anyone designing 40mm Noctua cooling ducts for any and all printers...

The cooling duct employs a 24V 5015 fan that moves more air than the stock fan, so I've decreased my cooling fan speed to accommodate its increased airflow. At some point, I may redesign the cooling duct because it obstructs visibility of the nozzle...

This is a remix from superpotatofudge's [CR-10 40mm Stock Hot End Cooling Duct](https://www.thingiverse.com/thing:2160958). I redesigned the thing with radii that match the Noctua NF-A4x20 fan. Also replaced the original hot end attachment with...

Additionally, I'd been using a popular ring duct, but as it's only supported by the fan attachment bolts, it sagged over time due to heat from the nozzle until it hit the print. This remix fixes several problems with the original design and improves...

... picture) is burnt on the silicone sock. I just lowered it by 2mm. Now there is no more deformation or burning. Furthermore, I have adapted the construction better to the Ender 3 original housing. Have fun with it, you will be happy. ...stay cool

Optimised flow for more cool air for the extruder

In an effort to bring more fresh air into the air circulation constrained electronics bay of the Ender 6, I added a round duct to the 5015 fan intake. The plan is to use a step drill to create a large 30mm ish hole in the top plate of the electronics...

10-24-19 Update: Enhanced model features increased clearance within nozzle and optimized mounting holes for precise alignment toward nozzle.\r\n\r\nRecent adjustment since 10-9-19:\r\n-\Improved mounting hole clearance for added leeway in mounting...

When I got a Micro Swiss all metal hot end and Direct Drive system for the Ender 5 Pro, no Hero Me or anything matched what I wanted. I wanted to move the fans separate from the Hot End Mount. This mounts directly to the Micro Swiss Metal Carriage...

remixed for ender 5 plus with microswiss direct drive kit. notch added to clear belt mounting. ...slightly larger clearance hole for microswiss plate mounting.</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Prusa</p> <p...

I added an airduct for 40x40x10mm or 40x40x20mm silent noctua fans on the right side for part cooling. All mounting holes are diameter 3,8mm for threaded M3 inserts. There is a version with a box cutout on top for step down converters. The left...