ender 5 control board 3d models

Simple case for the 3018 control board (I don't remember the exact model of the board, but you can see the board in the picture), and the control board for the Sainsmart laser board. There is a spot to mount a 40x40 fan as I had an extra one laying...

Simple case for the 3018 control board (I don't remember the exact model of the board, but you can see the board in the picture), and the control board for the Sainsmart laser board. There is a spot to mount a 40x40 fan as I had an extra one laying...

This allows quick access to the control board and internal components without removing the entire lid, resulting in a more professional appearance. Test prints on the new design are ongoing, so it's considered a work in progress. The original designs...

The cooling fan location has been raised and moved closer towards the back of the control board for better cooling of all heat sinks, and the fan cover fits for a Noctua 40x40x20mm fan upgrade, that will not touch the Pin 27 / EZOut board upgrade. ...

I tightened up the fit since the original was too loose when I tried it on. I also attached the lower part so there's no gap left behind. The print came out perfectly standing upright, still no need for any adjustments. ...I'm considering adding some...

It has a place for the following items: - Original Ender 3 Melzi Board (1.1.3 in my case) - 3D-Freunde Mosfet V2 (the big one) - 4x TL-Smoother Plus by Trianglelab (without screw holes) - 2x relay module IMPORTANT: I recommend disassembling the old...

... If you are planning to switch to the new SKR V1.3 32-bit board, be sure to check out my modification for that board at https://www.thingiverse.com/thing:3558321. ... The Fusion360 file is included with this design.

UPDATE 04.03.2019 I've made different changes: aligned the position of some screwholes to fit better option to screw the box on the y-axis extrusion removed some mm onto the backside to fit better on printers with just a 220x220 print bed added some...

... the connection is at the back and out of the way. If you're switching to the new SKR V1.3 32-bit board, check out my modification for that board here: https://www.thingiverse.com/thing:3558321. ... The Fusion360 file is included with this upload.

Fan Timer Control Board using NE555

WIP! Project require a lot of edits. ...Do not print! Update 29.05.2022:- Added case cover mount holes- Added cable tiers holderUpdate 28.05.2022:- Added PSU switch cover model for compatibility with PSU legs

Humans have crafted a device that minimizes its plastic usage, allowing it to print rapidly. ...Additionally, ridges were incorporated to enhance its stiffness, while slotted screw holes were designed to ensure precise placement.

BlinkyTape LED Control Board - Addressable LED strip controller boardhttps://shop.blinkinlabs.com/collections/frontpage/products/blinkytape-control-board?variant=985353020

... is a simplified model of the DEVIA Control Board of jjrobots (for details see jjrobots.com). ...Only PCB, connectors, LEDs and buttons are included. All dimensions measured at my own board (should be better than +/- 0,5 mm) and without any warranty.

Stay tuned for more ender 5 upgrades! Words of caution: Due to the small details, you will need to be cautious when removing supports. I'e, snoopy's tail and the fuse on the bomb character etc. ...pictures provided are as it came out fresh from...

This is an Ender-5 control cover that covers the back of the control panel to protect the electronics. Attached to that cover is a Raspberry Pi case with a 3" touch screen. I am running OctoDash in the pictures but you could run any of the...

Produce with a control board featuring ivory-material pipes and fittings.

I needed a cover for the K7000 control board on my arcade. ...

Hi everybody, This is a control panel used in my Ender 5 for my V1.1.5 and Mosfets. Basically, there are three modules: 1) The display module, for the original 12864. 2) The electrical part, for the V1.1.5 and Mosfets. 3) The 80mm fan holder. Then...

Flight sim extension MOD for Thrustmaster TWCS Throttle (HOTAS). ...Create a PC button box controller, based on Arduino Leonardo Microcontroller board.

Screw holes for the control board accommodate M3 and cover holes M2.5 sized screws.BoxAs the box has a circular hole for the BNC connector, I recommend printing this with supports (I haven't tried it without them).CoverNo supports required, but make...

The board also features options for downward wire routing through the board, which we utilized to reach lower control boards and CIM motors. This year, we additionally designed the board for quick detachment from the robot, enabling easy sliding out...

Made an IoT Control Board to control smart switches via HomeAssistant. It uses Amobea PCBs to help with the wiring of keyboard switches and WS2812B LEDs. The code runs on a Wemos D1 mini. The hinge is made with M3 screws. The USB connection is with a...

... around the MPU-9250 sensor module, allowing for seamless integration into your project's main circuit board. ...Meanwhile, the secondary control board can be securely attached to the peripheral board, providing additional functionality as needed.

It clicks securely into place in the groove of the bottom rail and wraps around the top edge of the control board. The design ensures a loose fit that prevents damage or pinching of control wires. ...If you have a suggestion on how to improve it, please...

MKs Gen control board mount. Designed specifically for use on 2020 extruded aluminum. ...Print Settings: Printer: Prusa i3 Rafts: None Supports: Yes Resolution: 0.3 millimeters Infill Density: Fifty percent

I'm creating a custom enclosure for my X5S Tronxy printer using its control board as a reference point. The major components of this board are clearly represented, which I believe applies to many other Tronxy printers as well. My goal is to help...

This design is for a deej volume control board, which controls the volume for individual windows applications. You can learn more about the project at https://github.com/omriharel/deej. To bring this project to life, you'll need an Arduino Nano,...

Peltier controller - NTC 10 k

The board I'm utilizing is a Chinese-made one: Bachin CNC GRBL 3-axis Control Board. v2 specifications: - A slightly raised bottom section to accommodate screws that secure the fan. - The fan on this version blows air over the X and Y axis stepper...