ender 5 control board 3d models

This case is to suit the Ender 5 with an SKR V1.3 or MKS Gen L. It is specifically designed for my application of adding a heated build enclosure. Therefore, it draws and expels air from the underside edges of the printer to avoid the hot air inside....

The Ender 5 is a great printer, but the bed support could have been better designed as it is hanging down in the front. Didn't find a support that I liked, so I made one myself. The bolds and nuts are M6, but probably will also fit 1/4". I used self...

This is a cover I made to clean up the cables on my Ender 5 Pro. Its made in 2 parts, the outer side (mount) which bolts to the extrusion using 4x M4 bolts and captive extrusion nuts. And an inner side (cover) that then slides over and bolts onto the...

I'm having issues with my Ender 5, as it keeps hitting the carriages against the far X rail when I try to set the bed size to 235 x 235 in Marlin. When I investigated further, I discovered that the Y carriage was roughly 4mm short of the silver...

Using 4.5mm thick acrylic panels for a simple enclosure mounted to the exterior of the extrusions of the Ender 5 plus using simple clips. I used M5 buttonhead bolts with T nuts and hex head bolts everywhere, just measure for the lengths required. ...

My ender 5 kept hitting the carriages against the far x rail when I tried to set the bed size to 235 x 235 in Marlin. I found that the Y carriage was about 4mm short of the silver corner brackets on the far side when it hit the Y endstop. When I...

Struts to support the bed on the Ender 5 (or similar), to reduce vibrations and generally increase stability.Buy me a coffeeI wanted to combine the best bits of this and this design and here is the result. Fundamentally, it's the 'compressive'...

It started off as a pro, I should have gone with the standard Ender 5 :) ## Future Upgrades Linear Rails Mod * Printed in SunLu Carbon Fiber PLA * https://www.thingiverse.com/thing:3845704 * In-Progress ## 1/24/2020 * Link to my Marlin fork with my...

Ender Five Module Z Activated \r\n \r\n Lunar Operations Unit Number Ten Lambda Upsilon Universal

This is a remix of the original VzBot (CoreXY mod for Tronxy S5A) adapted for Ender 5 (Pro), https://grabcad.com/library/vzbot-1 Things I used: - 2x Rat Rig LDO-42STH47-2504AC, Wentai 42BYGHW811 or E3D High Torque NEMA17 steppers, - 1x [380mm 2020...

... are fine in 0.2mm. Print with at least 40% infill, 5 shells and 5 top/bottom layers. Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: No Supports: No Resolution: 200 Infill: 40 Filament: Any ASA / ABS / PETG Category: 3D Printers

Stealthburner Mounting for Ender 3 and 5 After using the SteathySwiss mod for more than a year I had to reprint it after starting to print ABS parts in a enclosure as they started to warp because of the heat and that I printed them in PLA. As I...

Creality Ender 5 extruder arm. This device repositions the extruder, allowing for a drastic shortening of the Bowden tube. By doing so, you can significantly reduce the retraction value and eliminate stringing problems. The printer is secured with...

Watch this video on YouTube to see a 3D printed pen holder made for Ender Printers, which can hold pens or pencils securely in place.

This control-panel mount allows the panel to clear forward-facing braces, like the Zuff-Design braces that I used (and recommend).

A fast d20 control dial inspired by syvwlch's D20, Speed Design Edition. ...Print it out at a full size of 100%.

This is still a work-in-progress project that serves as a direct replacement for the control panel, effectively running a 60mm 12-volt fan.

This camera mount works with the Ender 5 and Logitech C922. It can be used for any 20x20 printer frame, but it doesn't have to be placed at a corner. Other cameras with a similar base fit too! The camera base is 42 mm wide on the front (at the...

Got the Ender 5 along with my CR10S5, really like the simple drive system they came up with, so I figured I'd give it a try even though it's brand new. One thing I noticed when doing the first prints was that the carriage had a little springboard...

This design mounts a Raspberry Pi Camera V2.1 onto the 2020 extrusion on the back side of my Ender 5 Pro using a T-nut. The design has two angles of rotation, one with the T-nut and the other one with a pivot screw. The design needs the...

Some parts I did for enhancing my Ender-5 Plus when doing the direct drive upgrade.Cable guideA fixation for the extruder cables. Needs a M3 x 6 counter sunk screw.</p><p><strong>Z-screw fixation</strong></p><p>The Z-screw holders need four M4 * 10...

This is the enclosure I designed for my Ender 5. The design took inspiration from the Prusa Ikea Lack enclosure. The height of the enclosure is adjustable to your liking. It's based around 25x25mm aluminum extrusions. Mine were 1m in length and I...

This is the enclosure I designed for my Ender 5. The design took inspiration from the Prusa Ikea Lack enclosure. The height of the enclosure is adjustable to your liking. It's based around 25x25mm aluminum extrusions. Mine were 1m in length and I...

https://www.thingiverse.com/thing:5111093 Using 4.5mm thick acrylic panels for a simple enclosure mounted to the exterior of the extrusions of the Ender 5 plus using simple clips. I used M5 buttonhead bolts with T nuts and hex head bolts everywhere,...

This is my enclosure design for the Ender 5, inspired by the Prusa Ikea Lack. The height of this enclosure can be adjusted to your preference. It's based on 25x25mm aluminum extrusions, which I used in 1m lengths and did not shorten. If you use...

Ich möchte euch hier mein Kabelmanagement für den Ender 5 vorstellen. Ich habe nicht alle Teile selbst entwickelt sondern habe folgende Dateien für Mich angepasst: https://www.thingiverse.com/thing:3967562 https://www.thingiverse.com/thing:4116655...

This is used on the front right (or left) of my Ender 5+, but it will fit any 40mm extrusion. The model can be mirrored in your slicer to put the rear wing on whichever side you like. It will clear the bed in any orientation. I added three micro...

... decided to merge both designs using Meshmixer and came up with this version. Bunker - https://www.thingiverse.com/thing:3028772 Control Box Lid - https://www.thingiverse.com/thing:2895382 If you notice anything that needs updating, please comment.

... thanks to Mr. ...Clown for making such a great control box. I wanted to be able to use a cable chain to run my power wires to the box as well as have a hole in the bottom to run my control wires into my cabinet. ...So I did this quick and dirty remix.

This frame is fully compatible with Creality Ender 5 and any other printer boasting a similar bed design and sufficient free space. However, it will not fit the Ender-3 due to its limited free space on the bed sides. The two frame sides of the...