ender 5 case 3d models

After researching possible causes, I suspected electronic interference from other components and decided to create a custom case to relocate the LCD away from the frame. While it's uncertain whether the problem was indeed caused by interference,...

I wanted an external electronics case, but I still have the original electronics. My printer lives in a filthy garage (and is enclosed), but it also has a Meanwell 600W, and I sit next to this clamorous machine during the workday now thanks to...

# Ender 5 Plus Case Replacement A remix of @Moederbeer case, I wanted to remove the large E5+ case enclosure and put the parts in a different container. I looked at a lot of cases, but couldn't find one I liked so I ended up creating this new one.

This is a bracket for the Ender 5 Plus controller case to move the cooling fan from the bottom to the rear of the controller case and cover the fan's old hole. The air will now be pulled in the front sides and exhausted out the back. The bracket can...

After converting my Ender 5 to Direct Drive, I was unable to use the mount anymore because the extruder would now crash into the camera when mounted on the front top rail. With this adaptation, I changed the mount to make the struts lean further...

Front case for standard Ender3 for the Duet3 min 5+. if you use both parts it classes up the front of your Ender 3. Plus its a good place to fit a fan to blow/suck from one compartment into the other. Still WIP need to make the lids. and a...

I designed this case for the Raspberry Pi 4 B to mount to an Ender 5. It connects to the back 2020 rail using T nuts, and has an arm to use the Raspberry Pi camera (V1 or V2). I've included mounts for LED lights (link below) and included pictures...

Started off wanting case for Octodash but none seemed to fit my LCD from amazon https://www.amazon.co.uk/gp/product/B01MRQTMTD/ref=ppx_yo_dt_b_asin_title_o07_s00?ie=UTF8&psc=1 So i made my own then decided i could mount it in place of my original LCD...

Started off wanting case for Octodash but none seemed to fit my LCD from amazon https://www.amazon.co.uk/gp/product/B01MRQTMTD/ref=ppx_yo_dt_b_asin_title_o07_s00?ie=UTF8&psc=1 So i made my own then decided i could mount it in place of my original LCD

This is a remix of Ender 5 casing TL smoothers by D_jespersen I have added a cover to ensure adequate spacing for heat dissipation while preventing any wiring from touching the diodes. ...

Ender 3, 5 Full Display Case to be mounted on Arm or extrusion

Mounting a Raspberry Pi Model 3 or 3+ Vertically on Your Creality Ender 5 3D Printer Using the Original Case as a Reference Point.

Remix TFT70 case that mounts over the hole of the stock screen on a Ender 5 Plus. Two clips center it and hold it in place. ...I used (4) 2.5x6 screws to hold the clips in place.

This is a magnetic snap-on case for the BTT TFT24 display to attach to a Ender-5 Plus printer equipped with a BTT SKR v1.3 or v1.4 board. Four magnets are holding the case onto the existing LCD cutout. Magnets: 4 pcs 10mm diameter and 2mm...

I created this Ender 'X' back cover and Pi case so extra cables can be tucked in and hidden from the front view. ... Materials used standoff screws (be sure to install standoffs before screwing into the case.)

Since the SKR E3 Turbo doesn't fit into the electronics box of the Ender 5 I designed an additional Case that can be mounted between the original electronics box and the LCD screen. The case can be attached with T-Nuts directly to the aluminium...

Mountings bracket to relocate the stock electronics enclosure on an Ender 5 plus to the rear of the machine outside the frame. This re uses the stock bolts that held the enclosure in the frame and M4 bolts and T nuts to mount the brackets to the rear...

This is a custom made Creality Ender 5 Plus complete bottom cooling case for ultimate cooling at half the noise. This uses 2 12v, near silent 60mm fans from RS components (RS Part number: - 696-3544) and 2 12v Noctua 40mm fans (NF-A4X20). Link...

I made following changes: - Rectangle case (for mounting it to the wall - put the cable hole from the upper side to the other side - set one support 10mm left (because it was exactly in the way of the beeper - set the case height 3mm more, so the...

I designed this case to move the Original screen outside the enclosure to make room for an SKR E3 Turbo mainboard. ...I used on the inside a mount from Thingiverse https://www.thingiverse.com/thing:4676133

Customized version of https://www.thingiverse.com/thing:1563872 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1563872

The case mount adapter clicks effortlessly into place inside the Ender 5 case, with the screen sandwiched securely between the two components by a M3 screw and brass heat set insert. I'm employing it successfully in conjunction with a Bigtreetech...

The human touch is a perfect fit for the Micro Swiss All Metal upgrade on the Ender 5. To get the most out of this combination, use PETG filament or something even better. ...One trick to ensure smooth operation is to carefully trim off one mount tab...

This is a modified Version of Marty_Z's Case https://www.thingiverse.com/thing:4790166 I needed a Case where my SKR2.0 Board, my RaspberryPi (aka Octoprint) and a DCDC downstepper (LM2596 for the fan) has space in. So i modified the Case... In the...

#HEY YOU GUYSSSS# **YET ANOTHER RPI CAMERA CASE...** So I designed and printed this case due to having a specific camera and no previously designed cases would fit properly.... So FTIJPI after I design it, lol. Added and swivel and tilt feature so...

So I designed and printed this case due to having a specific camera and no previously designed cases would fit properly.... So FTIJPI after I design it, lol. Added and swivel and tilt feature so ensure when assembling that you do not tighten the...

A human-friendly accessory that's a game-changer for Ender 5 owners: a sleek, screw-free raspberry pi case. This innovative design attaches effortlessly to the printer's sturdy metal frame, eliminating the need for tedious screws. ...With its compact...

This will be updated if I do so when the BigTreeTech SKR 1.4 is installed in my Ender 5 Plus. (Files have "rev2" present as my initial design was tidied up and reduced in size a little to produce this one. No earlier revision has been uploaded.) ...

Enclosure for BigTreeTech TFT35-E3 dual-mode screen, for replacing the standard display on the Ender 5 Plus.Requires a total of nine M3 bolts, 8 mm minimum length M3 × 8 mm (or longer - up to 12 mm) ×7 – four for holding the TFT35-E3 board...

Smaller case to replace the massive stock E5 case Currently in testing, any improvements pls tell me