ender 5 carriage 3d models

I have a tool box that perfectly fits on my Ender 5 Pro printer, taking into account its maximum build volume to prevent the bed from hitting the top of the box. The inside measurements of the toolbox are approximately 100x220x35 mm. It's also...

Using 4.5mm thick acrylic panels for a simple enclosure mounted to the exterior of the extrusions of the Ender 5 plus using simple clips. I used M5 buttonhead bolts with T nuts and hex head bolts everywhere, just measure for the lengths required. ...

Designing a glass enclosure using the frame on an Ender 5, I'm envisioning a 30" x 36" x .092" hardware store glass that will be expertly cut at every Home Depot and Lowes location. The design features main supports at each corner, along with strips...

The Ender 5 is a great printer, but the bed support could have been better designed as it is hanging down in the front. Didn't find a support that I liked, so I made one myself. The bolds and nuts are M6, but probably will also fit 1/4". I used self...

I struggled to find good Ender 5 BLTouch Mount. So i took the best one I found and made some modifications to it to make it stiffer and more secure. You use the two shroud screws and the top left wheel screw to hold it in place. I printed it...

This case fits perfectly with the Ender 5 and is tailored specifically for use with an SKR V1.3 or MKS Gen L mainboard, making it ideal for my particular project of adding a heated build enclosure. To prevent hot air from accumulating inside, this...

... of the Duet and mount the enclosure on the right bottom extrusion with some drop in (hammer) t-nuts and m5 screws (I used 8mm SHCS but there's nothing special about using SHCS). For more information: https://ender-5-mods.crpalmer.org/duet3d-upgrade

This case is to suit the Ender 5 with an SKR V1.3 or MKS Gen L. It is specifically designed for my application of adding a heated build enclosure. Therefore, it draws and expels air from the underside edges of the printer to avoid the hot air inside....

This is a cover I made to clean up the cables on my Ender 5 Pro. Its made in 2 parts, the outer side (mount) which bolts to the extrusion using 4x M4 bolts and captive extrusion nuts. And an inner side (cover) that then slides over and bolts onto the...

Struts to support the bed on the Ender 5 (or similar), to reduce vibrations and generally increase stability.Buy me a coffeeI wanted to combine the best bits of this and this design and here is the result. Fundamentally, it's the 'compressive'...

More info about clipper can be found at: https://github.com/KevinOConnor/klipper Design to convert your stock Ender 5 to COREXY with linear rails This design is in working phase, has been fully tested. Current model has Microswiss/Creality stock...

It started off as a pro, I should have gone with the standard Ender 5 :) ## Future Upgrades Linear Rails Mod * Printed in SunLu Carbon Fiber PLA * https://www.thingiverse.com/thing:3845704 * In-Progress ## 1/24/2020 * Link to my Marlin fork with my...

Ender Five Module Z Activated \r\n \r\n Lunar Operations Unit Number Ten Lambda Upsilon Universal

This is a remix of the original VzBot (CoreXY mod for Tronxy S5A) adapted for Ender 5 (Pro), https://grabcad.com/library/vzbot-1 Things I used: - 2x Rat Rig LDO-42STH47-2504AC, Wentai 42BYGHW811 or E3D High Torque NEMA17 steppers, - 1x [380mm 2020...

This is the Z Hall endstop for Ender 5, or other. It's made for 2020 profile, and to rotate the plug on 90 degree. For reference see the pic. There are 2 M3 holes inside the case to screw the board, but it is actually not needed. All components...

... are fine in 0.2mm. Print with at least 40% infill, 5 shells and 5 top/bottom layers. Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: No Supports: No Resolution: 200 Infill: 40 Filament: Any ASA / ABS / PETG Category: 3D Printers

Stealthburner Mounting for Ender 3 and 5 After using the SteathySwiss mod for more than a year I had to reprint it after starting to print ABS parts in a enclosure as they started to warp because of the heat and that I printed them in PLA. As I...

Creality Ender 5 extruder arm. This device repositions the extruder, allowing for a drastic shortening of the Bowden tube. By doing so, you can significantly reduce the retraction value and eliminate stringing problems. The printer is secured with...

This is the Z Hall endstop for Ender 5, or other. It's designed specifically for a 2020 profile and rotates the plug on a 90-degree angle.\r\nFor reference, see the included picture.\r\nTwo M3 holes are located inside the case to secure the board,...

Watch this video on YouTube to see a 3D printed pen holder made for Ender Printers, which can hold pens or pencils securely in place.

This is NOT official or approved by LDO, if they ask I'll take it down (no listing to indicate this is a remix - hopefully won't end up getting removed)----------------------------------------------------------------------------So the original wasn't...

https://www.thingiverse.com/thing:5111093 Using 4.5mm thick acrylic panels for a simple enclosure mounted to the exterior of the extrusions of the Ender 5 plus using simple clips. I used M5 buttonhead bolts with T nuts and hex head bolts everywhere,...

This is the enclosure I designed for my Ender 5. The design took inspiration from the Prusa Ikea Lack enclosure. The height of the enclosure is adjustable to your liking. It's based around 25x25mm aluminum extrusions. Mine were 1m in length and I...

Some parts I did for enhancing my Ender-5 Plus when doing the direct drive upgrade.Cable guideA fixation for the extruder cables. Needs a M3 x 6 counter sunk screw.</p><p><strong>Z-screw fixation</strong></p><p>The Z-screw holders need four M4 * 10...

This is my enclosure design for the Ender 5, inspired by the Prusa Ikea Lack. The height of this enclosure can be adjusted to your preference. It's based on 25x25mm aluminum extrusions, which I used in 1m lengths and did not shorten. If you use...

This camera mount works with the Ender 5 and Logitech C922. It can be used for any 20x20 printer frame, but it doesn't have to be placed at a corner. Other cameras with a similar base fit too! The camera base is 42 mm wide on the front (at the...

Ich möchte euch hier mein Kabelmanagement für den Ender 5 vorstellen. Ich habe nicht alle Teile selbst entwickelt sondern habe folgende Dateien für Mich angepasst: https://www.thingiverse.com/thing:3967562 https://www.thingiverse.com/thing:4116655...

you have to open all the zip file to see the file all the stl files are for printing parts to build this chamber I will add solidworks file if you need a adjustments also I add a hole for raspberry pi camera to use octoprint you could see on the...

Riser legs/feet for my Ender 5 Plus are designed to work seamlessly without any modifications to the printer. They incorporate a 2020 extrusion keyway that locks into place within the E5+ frame, and a recessed hole at the bottom allows for easy use...

This design mounts a Raspberry Pi Camera V2.1 onto the 2020 extrusion on the back side of my Ender 5 Pro using a T-nut. The design has two angles of rotation, one with the T-nut and the other one with a pivot screw. The design needs the...