ender 5 cable management 3d models

I also added a cable manager I found on here. I printed two copies of it, one mirrored (Simplify 3D brings it in HUGE - scale it to 10%). The mirrored copy I mounted on the filament carrier, the other on the back side of the frame. ... Printing it...

... and 1 m5 screw and Tnut to mount the back one to the extrusion. Of course 4 zip ties to secure the cabling. Acknowledge my work by putting a like if you download it. ... It's Free print on its sides and there will be no need for supports.

### A durable and stable mount for E3D Hemera If like me you have an Ender 5 (Pro, Plus, Standard) this will be the last mount you will print. In a few months I have printed practically every single mount I have found on the web. I was so desperate...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

Wire organizer Wires on my Ender 5 were too short to secure against the frame so I created a set of interlocking panels. You need 2 top panels, 1 corner panel and 1 Ender port panel with t-nuts and 5mm crews. Also added a spool holder riser to fit...

Motor side: Two cable chain adapters for johnniewhiskey's Ender 3 Cable Chain (https://www.thingiverse.com/thing:2920060) are used in my design. One adapter leads outside the enclosure to the electronics box, while the other leads inside the...

Hello I have designed a cable management box that can be installed in the frame of the Ender 5 Plus. The box is screwed into the frame with 4 groove nuts. However, you have to loosen the back corner so that you can pull the frame apart a little so...

Kabel Kabelmanagement Kabelhalter für X- Y-Kabel Ender 5 V7 ist etwas kleiner als V6 prüft was ihr hier benötigt Weitere Informationen zu meinen Drucker Modifikationen findet ihr hier: http://jogiarea.de/ ---------------- Cable management cable...

Kabel Kabelmanagement Kabelhalter für X- Y-Kabel Ender 5 V7 ist etwas kleiner als V6 prüft was ihr hier benötigt Weitere Informationen zu meinen Drucker Modifikationen findet ihr hier: http://jogiarea.de/ Cable management cable holder for X- Y-cable...

These are my custom config files for the Ender 5 Plus with Marlin 2.0 Firmware on a SKR 1.3 motherboard (I have a 1.4 Turbo installed, but I haven't had time to update it yet). They are very specific to my machine, but I thought others might find...

Chain mount for ender 5 cable management. You can use these clips for the cable guides or just use zip ties. ... https://www.thingiverse.com/thing:4936515

Creality Ender 5 Plus 2020 2040 Cable Covers Will suit any 2020 / 2040 sections Creality Ender 5 Plus Cable Management (This was 100% infill) All parts are thin and weak but with care they work well. Remove using a paint scraper under the edge near...

After installing an Ender Extender, I encountered issues with the Extruder and X cables getting knotted in the bed whenever it moved all the way back. To resolve this problem, a bar is added that elevates them 7 inches, preventing them from being...

I like both this part: * https://www.thingiverse.com/thing:4654645 and this part: * https://www.thingiverse.com/thing:2924288 So I mixed them together for my Ender 3.

I needed this part for organizing cables of my ethernet cables. I needed them to be screwed down. ...Thus, I designed it!

... they performed well. The parts themselves are thin and fragile, but with proper care, they work effectively. To remove them, use a paint scraper under the edge near the clips and twist carefully. Creality Ender 5 Plus Cable Management Solution

Designed up this mounting bracket for ender 6 cable management to use in ender 6. . ... Printing: Printed in ender 6 Print time 35 minutes 100% infill Print Speed 200%

This is a simple rear cable management mount for the Ender 6. ...It requires 2 - M3x15 screws and 2 - M3 T-nuts.

I only printed one of each, thinking it would fail miserably, but to my surprise nothing was wrong. I hope these can help you too in managing cables on your printer (these clips will work with other printers that have aluminum extrusions similar to...

I created a simple cable holder just for my Ender 3, these slide into the tracks on the ender so you can use them in many places for any additional cables you may need.

This enclosure is specifically designed for the Ender-3 to keep cables organized. It includes space for a 3x6cm protoboard. ...To attach it to your Ender-3, you'll need M3 screws and V-slot nuts.

I created this cable management system that routes the cables in front of the z axis pillar to avoid cable binding as the gantry moves up. The cable mount pivots in the base for flexibility while the x axis traverses. ...I included zip tie anchor points...

This is a filament guide I remixed from a few people I was having problems getting the best of both worlds (cable management and good filament guiding). So, I did it myself and made this great filament guide. One downside is you need a connector for...

... have to place it where the Z-axis end stop already is. Extra parts. Chassis mount: M4 x 12mm + T Nut (x 4) M4 x 30mm + Nut (x 2) Hotend mount: M3 x 8mm (x 2) or the same by Ender Chain cable carrier https://www.amazon.it/gp/product/B094ZSWDWB/

The clip attaches seamlessly to the extruder's stepper motor and the t-slot bracket keeps the printhead cable out of the way as the printbed moves. ...Fasten the cable with zip ties at the marked spots for extra security.

Creality Ender 5 Plus 2020 2040 Cable Covers Will suit any 2020 / 2040 sections (This was 100% infill) All parts are thin and weak but with care they work well. Remove using a paint scraper under the edge near the clips and twist carefully. Creality...

I got sick of looking at my wires just hanging around and wanted a low profile management system. Not the greatest design but my first. This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/5OMwtd6dnkd

This is a replacement for the stock Sprite cable management that removes the stress and potential cable fatigue from the x-axis movement. Like the originals, it bends the cable to the left and routes it across and down the outside of the x-axis...

The ribbon cable holder mounts the LCD rainbow ribbon cable to the frame to stop it interfering with the bed levelling wheels.The power cable holder securely routs the power cables from the PSU to mainboard on Ender 3 Pro.The sleeve cable holder...

I craft this system as a straightforward and effortless printable cable management system. The guide is 0.8mm thick in PLA: flexible yet robust enough. X support clips onto the roller axes, which remain stationary. To assemble properly, you must...