ender 5 cable management 3d models

A simple replacement cover for the top of your Ender 5 (Std, Pro, Plus) which allows you to route the cabling much cleaner. It also allows you to customize to the color scheme of your printer. ... In my example I did 2 color black/cyan (Layer 21...

I didn't like how the cables looked after adding my camera for Octoprint. I made these clamps to ensure it looked and performed better. Made a slightly bigger one to make sure I could clean up the OEM cables. They are a little short so I had to work...

# Cable Management System for Ender 5 ## Project : Hide/Fixe the cables of Ender 5 using as few screws as possible. ## Parts : * Fixation(s) for bed cables ✔ * Fixation(s) for Y/Z/E cables ✔ * Fixation(s) for X cables ❌ (WIP) * Fixation(s) for...

I just got an Ender 5 3D printer and I wasn't happy about the lack of cable management. So I decided to design these clips to help keep the cables from getting snagged. They should be printed without supports and laying down, not with the arms up in...

Cabling on the Ender 5 is a bit unsightly. This cable management make it look nicer - purely aesthetic. Note that most cables will require lengthening to be accommodated withing the conduit. The complete build require 4 conduit sections (one...

I just got my hands on an Ender 5 3D printer, but I was less than thrilled with the lack of cable management options. So, I took matters into my own hands and designed these clips to keep cables from getting tangled or snagged. Printing them without...

I decided to make a cable management box to match the toolbox by Jack Werner.Simple print, I used Velcro for attaching the lid to the box.

I was thinking about adding extension cables to my cables (I actually ordered the [connectors](https://www.aliexpress.com/item/32991008328.html) I needed from Aliexpress) but then I was looking at a post about adding braces to the corners of the...

 I was thinking about adding extension cables to my cables, and actually ordered the connectors I needed from Aliexpress, but then I was looking at a post about adding braces to the corners of the ender 5 (such as this set from dbltrbl023 or this one...

This is a cable management tube design that does not require lengthening of any cables and does not require moving of the power supply. It is affixed to the frame with two cable ties. It is a bit of fiddling to fit it all together but just work...

This Cable Management System for Ender-5 and Ender-5 Pro was designed to hide and secure the great majority of its cables. To use it you need to extend some of the cables. Very simple procedure it you already used soldering irons. It is not a...

BUT you will need one "cable chain dual male end" to attach the Y AXIS REAR DRAG CHAIN BRKT to the rest of the chain > Some glue is required, Gorilla Super Glue Jell worked well for me > You will need "Ender_5_Plus_-_Bed_Strain_Releif_Bracket_Arm2"...

Redesigned X Axis opposite side bracket to allow for referencing on glue up Additional Parts Needed: SonOvaSailor's Design: Print 1 - Heat bed plug link and 4 Chain Link Cover Long  found here https://www.thingiverse.com/thing:4570302/files...

Designed this to keep the wires on the ender 5 plus nice and neat. This is not a flimsy design, they are strong and keep wires well. The pieces attach to the extrusion with a couple screws and t nuts. They are the width of the extrusion so they...

V1 - Cable management for X carriage Simple and effective

This design is to allow cable management for a Micro Swiss Hotend & Direct Drive set for the Ender 5. The cables are guided to the back into a chain to finally connect to the frame. The main adapter needs to be printed with support. The...

Fixed some slicing errors Simple Cable Management box to hide the cludder on the Ender 5 Plus. Wire pass-through on the back and bottom. ... The lid can be fastend with M3 Bolts Mounting holes to fix the box on the extrusion are provided Walls...

I created these inner channel clips to keep your Ender 5 plus cables hidden, neat and tidy within the frame. There are two sizes you can use (small & big), it depends on how many cables are in the channel, you'll use the small or big one. Print it...

I created these inner channel clips to keep your Ender 5 plus cables hidden, neat and tidy within the frame. There are two sizes you can use (small & big), it depends on how many cables are in the channel, you'll use the small or big one. Print it...

Includes two screen holders, OEM((beta) please inform me of good print, thanks) and Reprap discount full graphics Meanwell PSU supported, info here https://www.youtube.com/watch?v=wyKYZ-oBXM0 Bow 5/64" 140mm x 83.5mm plexiglass to install on Meanwell...

A minimalist aesthetic is being implemented. Still navigating TinkerCAD's capabilities, yet it proves sufficient for the task at hand. ...Essential materials include M3 or M4 machine screws and corresponding T-nuts.

Cable management for Crealitys Ender 5 and Ender 5 Pro. It looks like a cable chain, feels like one, probably tastes like one too but it won't work as one the way i used it. Its meant to be mounted on the frame. ... You'll need M3 screews M3 nuts M3...

Cable management for Crealitys Ender 5 and Ender 5 Pro. It looks like a cable chain, feels like one, probably tastes like one too but it won't work as one the way i used it. Its meant to be mounted on the frame. ... You'll need M3 screews M3 nuts ...

Bracket for the support of ender 5 plus calbes. Mount vertical or horizontal. ... May fit other models

The ender 5/5 pro are great printers, but once mounted the cable management leaves something to be desired, taking the best ideas here and there, and remixing some, with the addition of a few creations. I was able to provide you with this kit. ...

In Creality Ender 5 3D printer, cables are pretty much left floating. While some people have already created a strain relief plastic piece for the heating bed, i haven't found any for the X-axis cables, so i decided to create a couple of pieces...

Mounting a 22mm button on an Ender 5, also possible with other printers that use the same V-channel aluminum extrusion construction. ... I use it to turn on my DIY Bed illumination, 24V LED strip, fed from the powersupply, high density and only 30cm,...

I made some modifications to allow for smooth insertion of cables and wires into the clip. ... I took an additional step by adding a brim to ensure that all parts adhere securely to the bed.

Hello, I designed two different cable boxes to discreetly hide the tangled cables on the Ender 5 Plus. There are different openings in the box. The 2 openings in the bottom are for the Z-axis motors on the left and right. The 2 side openings on the...

Hello, I designed two different cable boxes to discreetly hide the tangled cables on the Ender 5 Plus. There are different openings in the box. The 2 openings in the bottom are for the Z-axis motors on the left and right. The 2 side openings on...