ender 5 acrylic enclosure 3d models

I saw RCLifeOn's version of this and I decided to make my own using 8" x 10" acrylic from Lowes/HomeDepot that was printable on the Creality Ender 3.

This is enclosure for [Mellow FLY TFT V1 3.5 inches](https://aliexpress.com/item/1005004091787313.html). ...The enclosure was designed for Ender 3 printer.

I'm working on Ender 5S 1 Enclosure Project. ...Enclosure will be ready soon :)

The new dimensions ensure a seamless fit on the Ender 3 print bed by disabling skirt mode. Refer to comments for detailed modifications. ... 1/4/2020 - Revised alignment improves base positioning against the wall without introducing any additional...

This is a DIY enclosure for the Creality Ender 3 V2. Printed parts list: (OPTIONAL) 1x hacksaw_block 16 x 4_mm_plexiglass_fixing 8 x 20x20_three_way_corner All other printed parts that is included in the download but not listed above is so...

Ender 3 complete 3D printer enclosure using 1/2in pvc pipes.

Ender 3 complete 3D printer enclosure using 1/2in pvc pipes.

*Still working on adding everything and putting together* IKEA Lack Ender 3 V2 Double Enclosure. ...

... to sit on for vibration reduction. I caulked all around the acrylic sheets to seal the enclosure. I also use underneath the stand for storage of tools. My filament dryer and controls are at the top. ...I have been using this stand for over a year.

This is an enclosure I came up with to house the main board and a Raspberry Pi Zero WH for my Ender 3 after updating to Klipper firmware. Klipper does not utilize the main board sd slot so I made a nice uniform front face. I also made the enclosure...

This is an enclosure I came up with to house the main board and a Raspberry Pi Zero WH for my Ender 3 after updating to Klipper firmware. Klipper does not utilize the main board sd slot so I made a nice uniform front face. I also made the enclosure...

Enclouser for your 3D printer, Fits Ender 3 Designed to laser cut in 6mm Plywood and acrylic glass door in 3mm Door hinge for acrylic glass door can be 3d printet in one piece If you like, please Tip :-)

Enclosure for Ender 3 Double component ventilation Parts: 4 pcs threaded socket...

Enclosure for Ender 3 Double component ventilation Parts: 4 pcs threaded socket...

A simple way to keep the enclosure lid on my Ender 6. No new hardware is required. ...The stock enclosure screws are enough to hold the clips in place.

 Thinking that the Sovol SV05 was the same dimensionally as the Ender 5 Pro because of the clear inspiration, I printed the original design by Capsopie and found the pieces a bit long by about 28mm for the Ender 5 pro.  Since there was a gap between...

A very simple laser cut top for the Ender 6 Yellow mounts i made from here - https://www.thingiverse.com/thing:4718662 Handle for door i made from here - https://www.thingiverse.com/thing:4768759 3mm Acrylic - 50cm x 50cm x 30cm Piano hinge 14 x M4...

This is a remixed enclosure this enclosure is taller specifically 8 inches so that it does not push down on the cables as much, the original creator messed up the dxf files and they were missing a lot of holes. some of the holes were a bit too small...

This is my take on the DuetWiFi enclosure for the Ender 3. It's designed to be a retrofit instead of using the stock electronics enclosure. You may need to extend your wires in order to use it without limiting your maximum print height. This is an...

I DESIGNED THESE CORNERS SPECIFICALLY FOR BUILDING MY ENCLOSURE FRAME AROUND MY CREALITY ENDER 3 - SO I PRINTED THEM IN SETS OF EIGHT, FOUR LOWER AND FOUR UPPER CORNERS, USING 25MMX25MM ANGLED ALUMINUM PIECES THAT WILL BE COVERED ON THE INSIDE OF THE...

Ender logo for your enclosure. Used the STLs from this print on Thingiverse (https://www.thingiverse.com/thing:3078936), and added a background. Printed with a filament change for blue on white finish. Print instructionsPrinted with PLA on MK3S+,...

... for LM2596 buck converters, such as this one found on Amazon. ...This enclosure slips neatly into the V-slot directly behind the electronic casing. Specifically crafted for use with the Ender 3, it will also fit snugly onto any V-slot extrusion system.

Collection of parts I needed to make an ikea lack enclosure fit an ender 3 pro. Many other listings claim to fit an ender 3 pro, but they don't. Modifications from the original design include: -Wider psu cable guide -Different psu mounts -Heatbed...

QUIET rattle free hinges for CREALITY Ender 5S1 enclosure , printed in 95A TPU THICK walls top/bottom layers 90% infill with supports ON , they look similar but they area top and a bottom my ender 5S1 has a solid metal bottom rail so you can't mirror...

This is a remixed enclosure this enclosure is taller specifically 8 inches so that it does not push down on the cables as much, the original creator messed up the dxf files and they were missing a lot of holes. some of the holes were a bit too small...

This is an enhanced version of the existing Ender 3 enclosure featuring several key add-ons: 3 independent fans that enable precise temperature control, allowing each fan to be turned on or off as needed A control box equipped with a digital...

Added front without Ender 5 text for other printer users. Back 2. Added a back cover with the mounts on top so it can be screwed to top. update 23/11/202 I've added a bottom enclosure with all EXP ports accessible, I've not printed it so please...

Previous I had to file it to be able to push board down. Removed some corners and added some chamfer to holes. Removed some of the text this is due to conversion and making mesh simpler. update 10/10/20 Front Added front without Ender 5 text for...

I'm going to need some ABS 3D printed parts in an upcoming DIY go-kart series, so I decided to make an enclosure for my Creality Ender 3. Being unsatisfied with both the cost and quality of available options on the market, I set out to DIY my own...

Doesn't the Ender 3 come with an electronics enclosure on the front left? It does, I threw mine out when I moved motherboard and raspi to the back, using TT's rear enclosure. I could have taken it again but it has fittings and holes where I don't...