ender 4 3d models

Remix of the RaspberryPi 4 Ender 3 enclosure to include a hole for a female barrel connector. I'm using the female barrel connector to connect the Pi to a power relay.More info on that can be found below.

I've taken part of https://www.thingiverse.com/thing:4107156 and created a remix featuring the STEP file shared by @drewzh for the Ender 3 pro case, adapted specifically for the Raspberry Pi 4 with dual fan setup. ...A dual fan option previously...

After upgrading to a BTT SKR 1.4 on my Creality Ender 3, I needed somewhere to put my board. Preferably in the front. Teaching Tech has one for the back. Design goals:- Under 2 hr print.- No supports.- Viewable faces flat on the bed for best...

A minimalistic electronics enclosure to put the BigtreeTech SKR 1.4 in a box at the front of an Creality Ender 3. Print instructionsDesign goals: Under 2 hr print. No supports. Viewable faces flat on the bed for best finish. Reuse of screws (M3's...

This is a case for Raspberry Pi 4 that is mounted to ender 3 v2 frame. Probably will fit any ender 3 and similiar printers. Case will fit the Pi, 40x10 fan with room for little heatsinks. I used 6mm heatsinks. There is not much room left after them...

This is a case for Raspberry Pi 4 that is mounted to ender 3 v2 frame. Probably will fit any ender 3 and similiar printers. Case will fit the Pi, 40x10 fan with room for little heatsinks. I used 6mm heatsinks. There is not much room left after...

Box for BigTreeTech SKR 1.4/Turbo board for Creality Ender 3 Pro/V2 printer with a cover with a lock or screws. ... A spring from a pen is needed for the locking version It is possible to use a 4010 or 4020 fan for cooling the electronics connected in...

I wanted it mounted at the front as it can be a nightmare plugging cables in if mounted at the back, i have it on the left but can't see why it couldn't be mounted on the right instead. The lid is held on by 4 m3x18mm bolts, the fan is held in...

Just took the nice 4040 rail design and enlarged it to fit under my pi 4 on my ender 3 v2. I left the plate full to fit multiple cases but for the canakit case, it's really easy to mark the holes through the bottom plate of the case to get a good...

I'm actually using one of my prototypes as the case now since I'm too lazy to reprint everything in black to match the frame. Known Issues: Due to the physical size change between the stock Creality board and the SKR 1.4 board. I ran into the...

Known Issues: Due to the physical size change between the stock Creality board and the SKR 1.4 board. I ran into the unexpected issue of the Bed Temp Probe failing to reach SKR board by 1/2 inch. I made myself a short extension cable so be prepared...

The MKS Gen 1.4 board stretches significantly beyond the stock Ender 3 board, preventing it from fitting snugly into the stock enclosure. The enclosure protrudes slightly forward but positions the standoffs accurately to attach the MKS board...

The version of Despertaferro I used didn't fit my Ender 3/Raspberry Pi 4 combination. After several attempts and errors, I finally found a suitable fit. To install this custom version, you need to remove the LCD screen by unscrewing it, then slide...

I needed to relocate my electronics since I have ordered a thermal tent for my Ender 5. I didn't want the works to be fouled up in the heat so I went looking for a remote box to house the LCD and Raspberry Pi. Found MANY useful designs but nothing...

Minimalistic Fan Mount in the beginning was a mod for "MINIMALISTIC ENDER 3 FAN MOUNT", now it's a new design and new project. Version 3.0 is completely redesigned, and you can't use elements from version 1.0. Summary The Fan Mount v 3.0 has a...

The model has 1mm support poles built in, they snap off easy and I have a thing about support, best avoided :o) There's a pre-chopped G-code in there, for Ender 3 - with 3 shells, 1 percent infill with gap filling at 0.2 layers, perfect for most...

4.0. This is a third version of minimalistic Fan Duct. Minimalistic Fan Mount in the beginning was mod for "MINIMALISTIC ENDER 3 FAN MOUNT", now is new design and new project. Version 3.0 is completely redesign and you can't use elements from...

It's a situation requiring BTT SKR V1.4 technology and UPS 24v V1.0 equipment.

Little remix (it's redesigned by me for scratch but it's the same thing. ... Its designed for Raspberry Pi 4 with metal case. ...It have support for 1CH relay for power ON/OFF and some drill for cable management.

This case is designed for MKS 1.4 / SKR 1.3 and similar mainboards that use the same layout. It includes a 50x10mm fan and a cutted squashball. For the other feet you can use my squashballfoot, that has the same hight. The grid ist printed with...

Required parts: X-Rail: MGN12H x1 MGN12R 350mm x1 M3 8mm x4 Free-Nut M3 6mm x5 set or more Y-Rail: MGN9H x2 MGN9R 350mm x2 M3 8mm x8 Free-Nut M3 6mm x10 set or more Gantry: 2020 Extrusion 378mm M5 8mm x4 M5 25mm x2 T-Nut M5 x6 EVA2.4 BeltHook: M5...

The right side had its power button hole removed and replaced with Bridge 4's badge, a nod to Stormlight Archive fans everywhere. The supporting pieces around the fan have been adjusted so no additional supports are required. Tolerances for fitting...

I just got a SKR v1.4 Turbo and I wanted a nice case easy to print and with honeycomb. I updated the Case and Lid, with better tolerances for the magnets as I struggle a bit to make them fit in their place. Also the files are already on printing...

You can now use the cheaper Direct Feed hotend without a Bowden fitting. Enjoy and post your makes! If you found my Things useful, treat me to a cup of coffee by using the PayPal button below :) Buy me a cup of coffeeBuy me a cup of coffee $3.00...

Petsfang Blokhead Direct Drive (Page in Progress) http://www.petsfang.com/ ***** Installation video is here: What to print Shortcuts to the current Creality & Tevo "Files to Print" Docs is below. This takes you to an interactive spreadsheet with...

Hello All, Here is my proposal for an BIGTREETECH SKR1.4 (turbo) enclosure. In the box you can include , the BTT mosfet and the BTT relay V2. I had no need for raspbery. But maybe on the lid there is a bit room. The box is meant to by mounted on...

This is a remix of a really nice design by Jlmpenedoe. The USB and LAN ports have been modified so that the Pi4 fits perfectly. Although this version has not been printed, I'm confident that it will work flawlessly just like the Pi3 model. ...All credit...

Just my design of a Insta360 Go camera mount for the Diatone TinaWhoop. ...Super Simple.

A simple Y-axis tensioner, fluid screwing. ... Videos of the assembly : https://youtu.be/NFNiiNsCyNk https://youtu.be/HrTCUQoW-Ac Additional screws required for installation : 1 x M6 x 20 chassis screw 1 screw H M5 x 25 1 washer Ø5 1 Nut M5

Another version of the box for placing the SKR v 1.3/1.4 on the Ender-3 printer Source: https://www.tinkercad.com/things/bkxIadtlNi4