ender 3v2 upgrade 3d models

Just a quick remix of Pedro Lamas' electronics box to mount the SKR Pico V1.0 I used painted smart supports on Superslicer for the bits that go into the extrusion at the front.

This is a remix of the brackets from https://www.thingiverse.com/thing:4916389 and the the orbiter 1.5 mount from https://www.thingiverse.com/thing:4962523 The mount allows full X axis motion and factory mounting of bltouch. ... I designed it to use...

You will need a couple of M2 x 16mm screws and a bit of bowden tube (and some tape to hold the cover :D )Remixed from  https://www.thingiverse.com/thing:4337798  and https://www.thingiverse.com/thing:5382046

Work in progress. BLTouch mounted in the duct in line with the nozzle optimizing bed probing area. Probe offset x-0 y-42. Uses stock 4010 fans. Needs part cooling ducts, plenty to choose from on Thingiverse. ...Currently using these:...

Wanted a mount that was rotated 90 degrees to accommodate a direct drive extruder, but also didn't stick out over the 20mm frame. ... Influenced by 310weber's remix from builditfull

This is a quick Fusion360 designed for a Knob for Z-axis screw lead M8 2mm pitch. The screw hole has 2 degree, loose and tight. May need some filling if your printer is similar to mine. A quick filling will help to tightened the knob to the screw...

Basically the same, but without the wiring loom on the top. Created for some guy on facebook, it allows for you to use both direct drive and a 5015 for cooling. ...

I needed an riser for the filament sensor because I had installed a dual gear extruder. I had already used the filament guide before and then adapted it for my combination.For stability, I recommend printing the filament guide/riser on the side as it...

<p>Just a quick remix of <a href="https://www.printables.com/social/156910-pedrolamas/about">Pedro Lamas</a>' electronics box to mount the SKR Pico V1.0</p><p>&nbsp;</p><p>I used painted smart supports on Superslicer for the bits that go into the...

Removed some extra material that was preventing the clip from properly sitting on the stepper motor. Since the motor has differing dimensions for the black vs silver sections, the original did not fit quite right. I also removed a portion of what...

Adds rigidity compared to the original mount I made. Should allow nozzle change without holding the heatblock ( not compatible with mars orbiter, which has it's own derivative of this ) The nozzle will only be 8mm further than the original hotend,...

Remixed the original 5015 fan duct and slimmed the left duct down to make room for the CR Touch Also added a slot for an M3 nut to utilize the rear mounting hole from the original duct

Hello, I have remixed it by enlarging one hole for the roller screw and also adding Creality logo in front.

i changed my stock extruder for the sprite extruder, so i wanted to change the way the filament was being delivered to the extruder so i needed a filament guide, but i also wanted to keep the filament filter i was using before...

Update 2/9/22 - Modified the original bays add a cover for the fan opening & extend the bay forward another 50mm, This allowed for the 3 addition of buck convertor mounting spots on the left side and 1 on the right. In addition I modified the...

Update of the original file now with a suitable role

<p>Small pillar support required at rear only</p>

Variation of my Tool holder remix for printers that have installed the 2nd. Z-Axis motor. ...Designed to clear the second axis

This is a holder for an M18 sensor that can be used to mount capacitive/inductive probes for auto bed leveling. It allows to be mounted to the original hotend, without any disassembly. ...Needed: 2x M2 screw 8mm (7-9mm, maybe 10mm length should work) ...

original sharpie blender https://www.myminifactory.com/object/3d-print-sharpie-marker-color-blender-3d-print-custom-colors-and-gradients-3-and-6-marker-version-138353

filament holder that is lees than 2cm high, for smaller desk, table...

The mixed colour pics are the first version, the all black box pics is version 2 along with the new fitted mother board box https://www.thingiverse.com/thing:5383189 motherboard box New Version: printed and has knocked 4 hrs off the...

I remixed this to work with the camera that I had for my raspberry pi. See [the original](https://www.thingiverse.com/thing:3586443) for more details and assembly instructions, except for the camera case. You will need to print the angled arm...

I wanted to have a longer filament guide fitting into the aluminium profile. ...Printed in 0.2mm layer height with 20% layer fill.

remixed of the original tool holder, but meant to be positioned at the back right (corner behind screen) for those whose machines are at the left of their workspace. i added a lil tab becuase i found the original sometimes tilted inward with just the...

UPDATED VERSIONS HERE: https://www.thingiverse.com/thing:4881811 -BLTouch mounted in the duct in line with the nozzle optimizing bed probing area. -Large probe area; x 0-220, y 0-199mm. -No more incorrect readings from a slanted or unlevel...

I made this extender with support from https://www.thingiverse.com/thing:4606033. The reason where that I thought the setup was a little wobbly when used with https://www.thingiverse.com/thing:3863544. This design gave the setup a more rigged...

It won't let me tag, but also remixed from https://www.thingiverse.com/thing:4857870 I wanted a better design for the tool holder for dual z users, so I took it into my own hands! I changed it so the shears are put inside a sheath instead of...

This is a remix for a Satsana fan duct with 5015 blower & and the Orbiter DD extruder mount. It is a remix of this orbiter mount https://www.thingiverse.com/thing:4668934 and this satsana https://www.thingiverse.com/thing:4647053 and the bltouch...

<p>Loved the simple and solid design that Mulilla made, but I found that the left locking tab was very delicate. &nbsp;I replaced the tab with a thicker tab, without the locking knob. ...&nbsp;The locking function isn't needed anyhow and now the tab is...