ender 3v2 dual extruder 3d models

Dual Gear All Metal Extruder Found Online Has Filament Input Positioned Differently Than Original Plastic One. Exactly 9mm Away From Support Plate. This Discrepancy Results In Non-Alignment Of Filament Sensor Output Orifice With The Extruder's Input...

Dual extruder/Dual Color material keychain '3DPrintitall'

Remixed from https://www.thingiverse.com/thing:5571975 to match height and alignment of WINSINN dual gear extruder - no additional hardware needed height is 6mm added countersink for screw holes for mounting to bracket (use 2 original screws)...

Bracket used to align the Filament Runout Sensor with the Micro Swiss Dual Gear Bowden Extruder that is being installed on one of the 3D printers listed below.Compatible with:Ender 3 MaxEnder 3 Max NeoEnder 5 PlusCR-10 V2Use two of the four screws to...

Firstly, the original design of the extruder cable holder for anybody that upgraded to the dual gear extruder is briliant; simple and effective. However, I noticed that the original design screw countersunk hole is a tad too thick to my liking...

Had wheels, axles and bearings left over from work on this [adjustable filament spool holder](https://www.thingiverse.com/thing:3648130/) and wanted not only to reuse them, but to have a matched upper and lower guide with lower guide at suitable...

for bigger metal extruder

This remix from the original changes the location of the tube hole so that it aligns to the dual gear extruder shown in the photo. The hole placement isn't perfectly aligned, basically eyeballed it but it's close enough since the rubber bushing...

I scanned in the filament sensor and created a shim so that the new dual gear extruder lines up with the filament sensor. Otherwise the filament has to make quite a turn...Which may be fine for flexible filament, but won't work with others. This...

remixed to add dual extruder

Dual extruder calibration test print

Ender 7 Extruder Fan Duct has a great design. So i decide to re-design the fan duct for E3D V6 hotend in order to fit my X Axis Carriage on my RepRap 3D Printer. You Will need for assembly: 1. x4 2 * 2 mm Blower Fan 4010 screws 2. x2 3 *...

This is a remix of Bart-tech3D's Ender 3 Direct Drive Extruder. It's a very simple remix that removes a 2mm section of the model to allow the metal Creality BLTouch mount to be used. The BL touch mount will fill in the removed area of the stepper...

I designed this part specifically for the WINSINN dual gear extruder to prevent filament from coming into contact with the Z axis rod. I also included a cable tie mount to keep cables organized and out of the way. When installing this part, push it...

The height is optimized for the CR-10s Pro Dual Gear Extruder linked below. !!! https://www.amazon.com/gp/product/B07SY745CF If you have a different extruder, you will need to adjust the height of the mount accordingly. You will need to print the...

You can find the same extruder on AliExpress using the link below. The mount for the extruder will fit most CR machines, you just have to drill your own holes to mount the extruder as each is slightly different. The original MBOT3D shroud...

Compatible with Satsana Neo 3 Fan Cage.I used a 23mm stepper (required if you don't want it to hit rail) - I Had to reverse the two center wires on my ender stepper cable (Blue and Green) for this stepper. This one is on amazon for $8.88 at the...

The case has mounting holes for different cooling packages which might come later. __________________________________Required non-printable parts____________________________________________2x M3 nuts3x M3x40 countersunk screws - for mounting the...

... I found I needed room to cut the end of the filament off before pulling it back through the bowden tube. Rev 3:Added additional brackets that will work with the adjustable direct drive kits that work with the single and dual gear extruders.

I designed this to snap on the extruder arm and help guide the PTFE tube with filament into extruder to avoid bending the filament (see picture without the guide) Support needed for printing the PTFE tube guide.

Dual model for calibrating dual extruder printers (IDEX)

Dual Extruder Alignment Verification Test Print.

Dual Extruder Alignment Verification Test Printing

Glub but dual extruder have fun :3 !

Cable guide for Sprite Pro for Ender 3v2. Mounts to the top of the old extruder motor mount. ... Needed Hardware: 4x M3x8 screws, 4 M3 washers and 4 M3 nuts.

With it being a Ender 3, I was quickly running out of space, so I remixed the following from: Dual Extruder: florentmarulaz - https://www.thingiverse.com/thing:3413260 Dual Spool Holder: ptajdus - https://www.thingiverse.com/thing:3498855 Combined...

To set the length to 7mm, use the following command: M412 D7.\r\n\r\nM412\r\necho: Filament runout ON\r\nFilament runout distance (mm): 7.00\r\n\r\nFor mounting the filament sensor to the extruder mount, you will need:\r\n4x M3 nuts\r\n4x M3 x 12mm...

... calibration model. ...The distance between the lines is 0.1 millimeters. The center is marked with a dot. Print Settings Printer: Creality Ender 5 Plus with Dual Switching Extruder Rafts: No Supports: No Resolution: 0.2 Category: 3D Printing Tests

Remix from https://www.thingiverse.com/thing:3833174 I Added some extra support to prevent bending, and also a chain adapter for https://www.thingiverse.com/thing:2920060 Haven't tested yet.

Frustrated with pneumatic couplings consistently failing to hold retracting settings? ...I was too, which is why I created a solution.