ender 3v2 dual extruder 3d models

Auto Power off Switch for Ender 3v2 made on a 3v2. Connect a Switch in row with the existing general switch on the back of the printer. For further information on how to open the case e.g. see this post: https://www.thingiverse.com/thing:4779435 ...

... LF = Left Front RF = Right Front LR = Left Rear RR = Right Rear Tested on Ender 3v2 but might work for Ender3/3Pro and possibly CR series. If you only what the bed locks, you can print 2 sets of the Rear bed locks and use them as follows...

This mounts a small size dial indicator onto the Ender 3V2 hotend using the existing BLTouch mounting holes. The mount can be permanently attached without interfering with normal operation. The dial indicator provides a more accurate and easier...

The bracket for the cellphone connects / locks into the default Ender 3V2 screen bracket. I included two types of brackets to use the cellphone in landscape and portrait mode. ... *Even though it is designed for a Galaxy A21 it should fit most 6,5 inch...

A BMG direct drive mount for Ender 3V2, designed to work with the Satsana fan duct (https://www.thingiverse.com/thing:4623647). The plastic bracket supplied with the BMG clone is used and attached with suitable screws (may need to drill and...

However, these run on 12V, while the Ender 3v2 runs on 24V. I didn't feel like using a buck-converter, so all I had to do was design my own cover. Also this design can be used with the original feet. I used these fans and am very happy with...

It is very easy to assemble and disassemble, holds the hotend solidly, works seamlessly with the Ender 3V2 carriage and uses only 4 screws; the backplate mounts to the carriage with 2, and the BLTouch mounts to the fan carrier with 2. The rest...

El ventilador de capa es un 5015 de creality para que quede silencioso ( https://s.click.aliexpress.com/e/_AoUwlB ), en el Hotend colocamos un 4020 de Sunon ( https://cutt.ly/av0drOS ), lo instalamos en una Ender 3v2 pero el mod esta adaptado para la...

I'm adding a second Z stepper motor/screw thanks to the Dual Z Axis Ender 3 / 3Pro by CR83D Since I'll be using direct drive extruder I no longer need the original part with extruder mount. In my case it was bent uneven, so the 3d printed part...

Remix removed text from face of the cover and worked on fitment/contour to match Ender 3v2. 1. (MicroSD Cover with Angle - Full Panel.stl) Added a nice angle to allow for easy removal. (This one is my favorite). I added some extra support...

... ...I repositioned the holder screw hole of the bracket so it does align with a hole on the metal part of the extruder on the Ender 3 v2. ... This allows to better secure the bracket against the gantry and resulted into more accurate readings for me.

Ender 3V2 Unitak Direct Drive wire guide No amount of zip ties and trying have I ever managed to get all the wires in a place that didnt either catch on the frame when calibrating before a print or when bed levelling, or if i did it looked an eye...

It secures to the frame using the two screws in the front of the ender 3v2 extrusion on the left side so needs no extra hardware. The fitting for the screen to clip on to it is deliberately tight. You will have to sand a little off for easy fitting...

Version 2 available: Ender 3V2 Damper Feet (Soft Springs) von AaronLK As far as I can remember my engingeering-courses the machine should sit on springs as soft as possible to reduce vebrations from/to the environment. Standing on a IKEA Lack table...

This combines a bed handle with the bed level knob locks. Bed Locks are labeled for easier install... LF = Left Front RF = Right Front LR = Left Rear RR = Right Rear Tested on Ender 3v2 but might work for Ender3/3Pro and possibly CR series. If you...

Remix removed text from face of the cover and worked on fitment/contour to match Ender 3v2. (MicroSD Cover with Angle - Full Panel.stl) Added a nice angle to allow for easy removal. (This one is my favorite). I added some extra support inside at...

Niggled me constantly after that, consequently I designed and printed this small cover for the Z plug.  The ender 3v2 z stop connector comes out of the top of the circuit board enclosure and looked like way too much messing about to delete for little...

The pen is mounted on the ender 3 v2 extruder gantry using m3 threaded hole for touch sensor. ...The pen also can be easily removed and attach to the mounting with m3 bolts.Blog: https://www.ardutekno.com/Github:...

Industrial-grade extruder motor components utilized within Ender 3D printers.

Ender 3V2 Noctua 4020 fan mount This is a little design based on the stock Ender 3 V2 hotend cover. I dont think it will work for other Ender 3 models due to the carrier plate, but didn't tested. I needed to make my Ender more silent so switched to...

Made for my Ender 3 V2, should work perfectly on Ender 3 / 3 Pro except the extra hole will not be correctly aligned with the hole in the gantry plate. Currently used with a Satsana remix duct with a 5015 fan. Might replace with something even...

... the laser out in front of the CR-Touch. The ends of the bracket that are holding onto the extruder housing are slightly tapered, so that it holds on more securely. ... Designed using FreeCAD (using original bracket for dimensional reference).

This is a remix of my previous design for the Voxelab Aquila, designed instead for the Ender 3v2, which I also have. I wanted a very clean and compact design that held the ultra cheap runout sensor I purchased and guided the filament with a...

As those of us with Ender 3v2 machines will find out, the stock cooling duct will slowly deform and melt causing us to replace it. Many of us have looked for replacements, upgrades and anything else useful to fix this. I have ran other common hot...

Max Verstappen Lion logo extruder knob

... if you don't have an Ender3v2. Model is oriented properly with no resizing needed. Print with supports. If you are looking for the dual scrapper and cutter holder that's in my picture, here it is https://www.thingiverse.com/thing:4747273

It uses the top 2020 rail of the Ender to clip on a guide that pivots as the hot-end + extruder moves. This is a replacement for my previous design found here: https://www.thingiverse.com/thing:4876151 No nuts/bolts required - it clips in to...

As those of us with Ender 3v2 machines will find out, the stock cooling duct will slowly deform and melt causing us to replace it.  Many of us have looked for replacements, upgrades and anything else useful to fix this.  I have ran other...

A quick camera mount I made for my Ender 3v2. I am biased, but I think this is a really great solution for mounting pi cameras on this printer, and I was a little surprised nobody seems to have made one before. It is very secure, offers a good...

The ender 3 V2 hot end assembly attaches with one screw in the back, instead of two in the front on the ender 3 and ender 3 pro. ...I made a small change in this part to go around the screw on the ender 3 V2.