ender 3v2 3d printer
2041867 3d models found related to ender 3v2 3d printer.
thingiverse
Most of the budget 3D printers (Creality Ender 3, Pro, Cr-10, Anycubic, Anet, Geeetech etc.) currently available are based on 2020 (2040) aluminium extrusion. This handle will simply slide into the top bar extrusion and will help you carry your...
grabcad
it is coordinate type 3D printer.A 3d model of self saught out dimension 3d printer
grabcad
The Ender 3 Pro is a highly regarded open-frame 3D printer that has captured the hearts of many makers and enthusiasts alike. By taking inspiration from this beloved model, a new 3D printer design emerges with some notable improvements. One key...
grabcad
This is one of my 3D printer designs. Based on a CR-20 and Ender 3.I am a CNC machinist and I'm accustomed to more accurate machined parts, than what the Creality and any other alu extrusion frame can offer.I did not want it to cost too much and only...
grabcad
This is one of my 3D printer designs. Based on a CR-20 and Ender 3.I am a CNC machinist and I'm accustomed to more accurate machined parts, than what the Creality and any other alu extrusion frame can offer.I did not want it to cost too much and only...
thingiverse
Check out my new duct design: ###https://www.thingiverse.com/thing:4807645 Solar Orbiter Duct has the following features and advantages over this: - ender 3/pro/v2 compatibility - version with or without printed bltouch mount ( + bltouch cable...
thingiverse
This is an enclosure for the Ender 3 v2 but can be resized for any printer. This is made from 5mm mdf. I superglued it together and reinforced with 1 x 1 strips of wood. Any type of construction will do the job, I just didn't have a working pin...
thingiverse
ALTHOUGH THEY SHOULD ALSO WORK WITH OTHER 3D PRINTERS, I HAVE DESIGNED THE PROJECT AND THE RELATED G-CODES FOR MY OWN USE AND TESTED ONLY ON MY CREALITY ENDER 3 PRO PRINTER. IN THIS RESPECT, I ASSUME NO RESPONSIBILITY OR LIABILITY TO ANYBODY FOR ANY...
thingiverse
To make this enclosure, you'll need: * 10mm wood dowels, cut to length for your specific printer model - These can usually be purchased in bulk for under $1 per 6ft section * A 3D printer to print the corner brackets - I used a cube design with...
thingiverse
This is a BLT-friendly remix of the very excellent [Satsana duct](https://www.thingiverse.com/thing:4369859) for Ender 3 series (including v2), for use with a 4010 hot-end fan and 5015 blower. The model preserves the original offsets I used for the...
grabcad
This 3D printer is specifically designed, drawing inspiration from the Reach 3D printer model.
thingiverse
I allso made the mount for right side instead of left, and extended the overhang arm for more center at the printer. I even made a hidden channel for the ribbon cable, so it was not hanging loose. If you mount the camera arm only with the back...
thingiverse
The original stepper-mount for the z-axis is not well made as incection molded part. The angle of the stepper-axis is not vertical. ...So I replaced the original part with this copy.
thingiverse
Another remix of the Satsana V52 with a direct drive bracket I designed. This one that I designed shortened the bowden tube length by 8mm. My previous setup was https://www.thingiverse.com/thing:4662728 The Satsana fan duct is remixed to be used...
thingiverse
Original design worked as it should. Didn't like how mall the pick up knob was so i added a knurled knob. It is a bit taller and more tactile to the fingers. ...No other changes were made to size of cover, fits the screen tight and lets very little to...
thingiverse
this is a camera mount for the tapo 210/200 + you will need to print the base wich was made by https://www.thingiverse.com/isaknybo/designs
thingiverse
https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...
cults3d
I have designed this tool myself since others don't work as well or at all. The works gagantiert ! No more filament breaks ! Clean konstrucktion ! ... Only 4 grams !
thingiverse
It's a small remix to fit the weather vane onto the z axis. Done in tinkercad, as a learning experience. Printed without supports and infill 0.24 mm layer height. The model was glued together and sprayed with gold spray paint. ... It looks...
thingiverse
Simple print-head design that uses the original two anchor screws to the gantry adapter plate, rather than the heat-break screws. ... Designed to fit by friction or screws, either side wedded to and supported by the main cooling fan, and to fit a 5015...
thingiverse
Made this display outline cover because I didn't want to print a whole screen case (too much red for the black&red theme I have). I ended up just making it flat so I could glue it on but I included a version that has a lip to sit on the case. knob...
thingiverse
original BL touch was mounted in a way that blocks the mounting to x carriage mount is from thingiverse making it difficult to adjust too toolhead i am also using cr touch mount comes from satana before using voron i was using this mount. ...thanks...
thingiverse
I need it, that I drew it and made it. ;-) Thrust me I'm engenier. This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/j25jFTdkoNg