ender 3v 2 3d models

Since I intend to use it with my Creality Ender 2 printer, I've added an arm so you can screw it underneath the spool arm for secure installation. This project is still ongoing, and I'll keep you updated on any developments. ...Feel free to try it out...

Print the "01_Test-Thread" object to check if it fits the nuts on your original Ender 2 spool holder. You may need to scale the object in X and Y direction (not Z since it will change the pitch). On my machine, I had to print the object at 99.5% X...

UPDATE: Version 2.0 is here: https://www.printables.com/model/382003-ender-2-pro-sd-card-adapter-and-wyzecam-v3-mount-v This is a mount I designed to add a Wyze Cam V3 to the Ender 2 Pro. There aren't very many good mount points on the printer...

This remix is designed to fit a 2.8 inch LCD display for the Raspberry pi: https://www.jaycar.co.nz/2-8-inch-touchscreen-for-raspberry-pi/p/XC9022. I used n602's 2.8" case and took some measurements from the inside of his case, incorporating them...

If you are printing this on an Ender-2 Pro, you will need to set the skirt loops to 0 to avoid going off the build plate. I used 100% infill, though, I am sure it would work just fine with less than that as the whole model is mostly walls. ...

I had an old iPad 2 lying around and decided to mount it to my Ender 3 Pro as an Octoprint controller. I printed it on edge with supports for the right section. I was concerned about weight and balance so added v-slot extrusions on 3 sides. It also...

On my Ender-2, I use a 1mm carbon plate coated with kapton tape: http://amzn.to/2nPggqi. **Extra Tip** Another valuable tip is to utilize kapton tape for an attractive finish and strong adhesion. You can purchase this product here:...

I could not find a 4010 blower fan, so decided to create my own adapter. Print Settings Printer Brand: Creality Printer: Ender 2 Rafts: No Supports: Yes Resolution: 0.15 Infill: 100 Filament: DaVinci Labs PLA Granite Notes: I drilled three 3mm...

---------------------------------------------- This is an adaptation of my unpublished Ender 5 Duet Mount, modified for the Ender 5 Plus. It utilizes a 40mm fan (recommended: 24v SUNON 4020 or 12v Noctua 4020 via a buck converter) to direct air...

SLOT 290mmHardware parts:16 pc - M3x10mm socket button head screw4 pcs - M4x15mm SH (socket head) screw4 pcs - M4x20mm FH (Flat head) screw4 pcs - M4x10mm SH (socket head) screw4 pcs - M5x35mm FH (Flat Head) screw14 pcs -...

I've been looking for good Z Axis support for my Ender 2 PRO, but what I found was too loose fit or doesn't fit at all - so I made my own in the end. Printing details are the description, but I also attached STEP file so you can edit this fix as you...

Hi, here's a combined part- and hotend cooling setup for the Ender-2. The part cooling fan is connected directly to the motherboard's K_fan connector; double-check polarity when making the connection. With this cooling configuration, there will be...

Rediseño de Manta https://www.thingiverse.com/thing:4403017 y https://www.printables.com/es/model/169185-manta-compact-fan-duct-tool-change-system de BoothyBoothy para mi Ender 3 pro, quería utilizar los ventiladores de fábrica y adaptar otro del...

Filament Spool Holder Designed Specifically for Ender 3 Series Printers. Perfectly Suited for Ender 3 Models. ... Ideal for Printing with Filaments of Widths Ranging from 90 to 100 mm.

A feeder arm for Creality Ender 3 to ease the angle at which the filament enters the extruder's motor.

My Ender 2 serves as a camera platform for precise camera movements, which has led to a distinct setup where the hotend would typically be located. As such, I cannot guarantee this mount will fit with additional components on the left side of the...

Hi everyone, here in Argentina there is two factories that produce filament but there is a problem, they use a 25mm center hole ( and, usually, doesnt fit in any spool holder of other countries ) this design can be used with the stock metal sheet of...

Second generation of my hotend fan duct for Ender 2 Pro. **Advantages:** - better air flow, - 4010 and 4020 fans mountable, - good view of the nozzle, - sturdy, - easy printing, - easy assembly. Print with heat-resistant filament, PLA is...

I grabbed an old iPad 2 gathering dust and decided to mount it to my Ender 3 Pro as a controller for Octoprint. I printed it on edge with supports for the right section. I was worried about weight and balance so added v-slot extrusions on three...

This is a straightforward SD card adapter for the Crealty Ender 2. The original micro SD slot can be quite frustrating, but I tried several alternative designs before settling on one that worked well and fit securely in place. To attach it to the...

This is a condensed version of the 'Pallets' component from the [Simple Graham escapement](https://www.thingiverse.com/thing:1128317), specifically designed to fit within the Ender 2 3D printer's volume, allowing all parts of the escapement to be...

I tweaked a fantastic TUSH remix from https://www.thingiverse.com/thing:2427540 I added grips to it so it fits snugly on the Ender 2 PSU, which needs to be close by the printer anyway (unless you modify the cables). At least now it serves a purpose,...

Housing designed specifically to replace the standard Ender 5 casing when utilizing the MKS TFT 3.2 mm touch display is now available. This housing provides ample space for the WiFi module and allows for easy access to the SD card from the side. A...

This tool holder encompasses all the standard tools provided with the Ender 2 and securely attaches to the existing hole previously utilized for the power adapter on early revisions of the printer. ... The print settings used were 0.2mm layer height...

I experienced severe warping on my Ender-2 printer while working with ABS, and discovered that a significant portion of it was caused by the unregulated air flow from the hot end fan. This cover mitigates some of the airflow towards the object,...

CringeHead is a direct print head for Ender 2 Pro with RBS (remote blower system) airduct. You need to use K3D minifeeder (https://github.com/dmitry-sorkin/k3d-minifeeder) as a feeder for this printhead (nema14 + bmg gears). Heatsink - any...

This is the Marlin 2.0 firmware preconfigured for MKS Sbase 32-bit boards installed on stock Ender 3 printers with 1/32 microsteps enabled. The auto extruder fan operates at a temperature of 50°C, and the part cooling fan is working as expected. The...

Original: This is a simple design for holding standard 20x20 crystals on Ender 2 beds securely. The main goal is to hold the side where the crystal exceeds the bed's right and bottom edges firmly in place. Right and bottom sides must be secured...

This design uses the stock metal sheet from the Ender and the two plastic nuts, which should be useful if you've experienced this issue like me. I printed my model at 107.18% scale in all axes (X, Y, and Z) to match tightly with the plastic nut. ... I...

I'm going to tackle the LED backlighting on my Ender-2 printer. Installation details will follow, but for now, let's just say that a few screws are required to secure it to the X-axis backside. The 12-volt LED strip I've chosen features three LEDs...