ender 3d v2

My PS Eye mount for Ender 3 v2. There is no need for screws. It slides right to the main 4040 profile of the base and the camera goes on the top of the mount. ...The camera base should slide right into the top of the mount and happily sit there.

This is a remix of:Ultimate Ender 3 V2 Nozzle Brush I've tweaked it so that you can print it without the supports and secure the brush with zip ties.Also, I lowered it a little because it would smash into it if you had ABL and did G29.

Hotend cover for Ender 3 V2, printed for reason to replace standard cover and fan. Can mount 60x60 fans with dirrerent width. Mount with three standatd M3 screws and need one M3 nut. ... Need some hand work to align with roller M10 nut.

Extension feet for Ender 3 Pro/V2 with useing original rubber feet as rubber inserts. Supports needed only in place for rubber inserts. ...Use two M3X20 bolts with M3 T nuts (or print M3 T nut inserts for regular M3 nuts) to secure the feet to the 4040...

Fits very tightly on the lower 40mmx40mm rails of the Ender 3 v2. Provides a "shelf" to support the wires and gives you something to tie wrap to. STL file contains left and right facing brackets. ... Print both or delete the one you don't need in...

If you have the Ender 3 v2 Adjustable Screen Holder or the remix, and your screen is loose, you don't have to reprint the entire thing again. Print 2 of these wedges and install then on the screen posts, behind the adjustable screen holder. ...If it...

My PS Eye mount for Ender 3 v2. There is no need for screws. It slides right to the main 4040 profile of the base and the camera goes on the top of the mount. ...The camera base should slide right into the top of the mount and happily sit there.

This cable chain mount screws into the Ender 3 V2 frame with M3 bolts. I designed it to be compatible with the common V-slot covers and also to be more in line with where the cables connect. ...Make sure to print it with the square part flat on the...

Made some slight adjustments to the hole placement to allow fitment onto the Ender 3 Pro V2 as the mounting plate is slightly different. I filled in the screw access hole that was on the front too. ... Simple screw into the bottom left (as...

This is a remix of this :https://www.thingiverse.com/thing:2932344 for the Ender 3 v2. I took off the left hand side and also took off the side notch because for some reason it made the z-rod bend to the left looking it behind. ... Follow the...

This is a replica of the control knob on the Creality Ender 3 V2. I basically just measured the original knob and recreated it, tweaked a few things here and there. I did this to make my printer more... colour co-ordinated :) Hope you guys enjoy! ...

... the way, so I made this. ...It is mountable on the Ender 3 V2, and I'm not sure about the pro. Definitely not the original, though. It is made for the raspberry pi 4b. ...Thanks to https://www.thingiverse.com/thing:4665097/ for making this originally!

... from Leroy Merlin, but can surely be used for other lighting fixtures. ...I chose this model because it is light and has the ideal length for the Ender 3 V2, I glued the mounting clips but they can eventually be screwed by making a hole on the support.

I haven't found nut that will fit my threaded lead screw in ender 3 v2 so i designed my own. On photo is version V1. V4 should be more easy to put in. if you have PETG print in PETG! ...I printed in cheap PLA for test.

... haven’t printed yet if anyone wants to print and let me know i can adjust. ...`It should fit the screws that lock in the slots. I took the idea from this https://www.thingiverse.com/thing:2757810 design added it to this to fit the ender 3 v2. ...

... but bltouch will be mounted 3mm higher. ... Original worked great with stock Ender 3 v2 hotend, but I replaced it with all-metal one which is slightly shorter for some reason and bltouch probe collided with bed.

Ender 3 v2 spool holder with bearings, fully printable. also has a removable stop at the end to prevent spool from accidently falling off the spool holder. Need to manually free bearing and apply lubrication if desired. ...I added a Spacer that is not...

For designers to make custom print head and other mods for the X carriage assembly on the Ender 3 V2 Neo. Update 2-16-23 3PM PDT: Corrected the position of the upper left V-Wheel, was off by 4mm. Added a missing hole at the top right of center on...

Tool Holder based on Mattwall model and designed to install in left side of Ender 3 V2. It include slots for screw driver, and fixed wrenchs than come with the printer. ...Additional slot was added to include a gauge thickness to calibrate the level in ...

The title says it all! ... This is a mount I designed to hold a Wyze Cam V3 on an Ender 3 V2 to view the bed as the printer is running. ... The design uses 2 M4x8 bolts and 2 t-nuts to screw the mount into the side 4040 extrusion.

Updated the mounting section with a boolean cut to accomodate the z-screw brass mount, which on the Ender 3 V2 is protruding of about 1mm. Also gave slightly more room for the z-screw itself. ... Added a second design, without the z-screw protection,...

I made some modifications to be able to adapt it to the ender 3 pro and v2 or other bed with the same chassis. ... I strongly advise to print the model with a resin printer,the model requires a lot of details in the teeth.

I really liked the big rollers for the Ender 3 V2 filament guide, but I needed a more flexible setup where my spool holder could be mounted on the side of the printer, needing a double roller setup. ... (Use the bearing guide/rollers from the original...

There wasn't a great filament adapter for the Ender 3 V2 out there so I designed this one and it works really well. You'll need to print the clip as well. See photos. ... This mounts to the printer using the two screws for the Z motor lead screw...

This is a simple bed levelling design. ...The Gcode included is for the ender 3 v2 bed size. stl is included so you can change the size to your bed. Its one layer high at .2 resolution. takes about 5 min. ...Enjoy!

Included is a ready-made gcode for Ender 3 V2 temp tower for PETG. E-Steps are set for my extruder, change line 21 in G-Code to your extruder's E-Steps.Comment out line 20 if you don't have BLTouch/CRTouch.

Fits very tightly on the lower 40mmx40mm rails of the Ender 3 v2. Provides a "shelf" to support the wires and gives you something to tie wrap to. STL file contains left and right facing brackets. ... Print both or delete the one you don't need in...

My Ender 3 V2 Mother board is on the top layer so the fan was at the botton with little to no air flow so I made a duel fan holder to mount on the side using the 20x40 extrusion as support

Simple screen cover for the Reality Ender 3 V2 Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.28 Infill: 20 Filament: Sunlu PLA Red Notes: I used Polyflex TPU, with tree supports with the camera...

A direct drive mount for Ender 3 V2 with adjustable X and Y axis. Made it adjustable for my dual gear extruder and possibly for other upgrades. Important note: make sure that X end stop is triggered, if not, add some spacer or bend the metal actuator...