ender 3d v2

The sensor requires the following hardware to assemble: 1x 5mm Ball Bearing 2x M2 x 6 machine screws 2x the screws that held the switch to the z endstop mount To setup your firmware to allow the use of the switch follow this guide:...

I couldn't find a Wyze V2 mount for my Ender 3 V2 Neo that did all the things I wanted so I made one. Attaches to the front with the factory screws. The actual V2 mount plate was made by jitterzPrintz and can be found here...

To be used to add an 11mm or 20mm height extension to your Ender 3 v2 These feet aid air circulation to the Main Board and power supply fans underneath. There is no need to remove the existing feet from your printer, just slip these over them and...

Ich habe das Level Rad für den Ender 3 V2 angepasst, da der Ender V2 nur M3 Gewindestangen hat nicht wie der Ender 3 und Ender 3 Pro. Das Original für den Ender 3 PRo habe ich hier her. https://www.thingiverse.com/thing:3676273 Ich habe die Datei...

This support has been designed for those who, like me, own an Ender 3 V2 Neo and have added a Creality filament end sensor. Impossible to find on platforms so I designed a perfectly functional one. This pack includes: Stand The pulley The screw...

 ❤ You can find my other matching knobs here:Drawer Knob:  https://www.printables.com/model/360832-professional-ender-3v2-drawer-knobBelt Tension Knob Covers:   https://www.printables.com/model/145383/Extruder Motor Knob:...

v2 Update - The hole for the probe is a bit wider so it does not have to be drilled at all, also trimmed it up a bit more to lower print time. I was able to use the existing top bolt by using a non nylock nut, but i may update it again to not need to...

Please make sure you have enough clearance before printing. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: 0.2 Infill: 20 Filament: 3DJake ecoPLA Black Notes: If you are printing on a Ender 3 V2...

A side-mounted spool holder for the Ender 3 v2. Will most likely also fit the original Ender 3 and 3 Pro as it just needs the 40x40 extrusion behind the left of the machine to support it. This holds the spool directly left of the extruder inlet...

I just bought my 1st 3D printer, a Creality Ender 3 v2. I did not like the way the filament was pulled at such a sharp angle into the extruder. So, I designed one that I like using TinkerCAD. It uses a common 608 ball bearing. I included a thumbscrew...

----- CAD: FreeCAD 0.20 Printer: Creality Ender 3 V2 Rafts: No Supports: No Resolution & Nozzle: 0.15 mm & 0,4 mm Infill: 100% Filament brand & color: unknown ------------------------------------------------------------ Lammcou GoPro...

As a result, only one of the two screw holes on E3D's fan shroud will line up with the holes on the Ender-3 V2's X carriage.I added an extra screw hole in the model, which aligns with the hole on the Ender-3 V2's X carriage. ...The mounting screw for...

... It worked nicely and was pretty stable. I've made a Satsana fan duct remix to fit with this one - https://www.printables.com/pl/model/206776-satsana-ender-3-v2-4010-fan-duct-with-bltouch-for-Printed in PETG, 0.2 layer height, 20% cubic infill

Ender 3 v2 4040 Front Switch PlateCreated in FreeCAD.Ender 3 v2, Generic PLA, 100% infill, 0.4mm nozzle, 0.2mm Layer height.I modified my Ender 3 v2 to move the power switch from the rear of the printer to the front on the end of the 40 x 40 alloy...

This is a Knob for the Z-lead screw, following the design of the extruder knob found on the Ender 3 V2. I followed the diameter for the hole used by Schtimpy, which was 8 mm.. But the final outcome was a very tight fit for the Ender 3 V2. I...

I liked the remix @mikelawrencenz made of the side stand angle printer brackets but neither the remix or the original top bar stand by @3d4LeyeF would fit on an Ender 3 V2 Neo due to the top bar having a flat surface with a hollowed out forward...

This is a Knob for the Z-lead screw, following the design of the extruder knob found on the Ender 3 V2. I followed the diameter for the hole used by Schtimpy, which was 8 mm.. But the final outcome was a very tight fit for the Ender 3 V2. I printed...

Not much filament and printing time required, a single screw M4 x 15 (in ender 3 V2 kit as spare) and a ball bearing 689RS (9 x 17 x 5). Supports required for the arm, check out in the pictures how to place items for printing. the pulley...

It's a piece which matches the screw holes and slide of the ender 3 v2 perfectly Using the roller from @daGHIZmo design (I choose to print it in TPU, but PLA can be just fine) to smooth filament gliding :) Please post you're own make it you have...

... the mount holes and mounted the BLTouch directly with a slightly larger set of screws. I used the install guide and firmware from Smith3D, which was super helpful: https://smith3d.com/ender-3-v2-bltouch-firmware-installation-guide-by-smith3d-com/

The front feet mount without issue on my Ender 3 V2, but the rear feet of 'Dr Boo's CR-10 Squash Feet' do not fit on an Ender 3 V2 due to the PSU mounting on the lower frame rails. This design allows for direct mounting of the feet using three T-nuts...

Adjustment wheel for each of the 4 screws on the Creality Ender 3 V2 and for other pinters that use the same style of bed level adjustment. The Wheel design is based on the original wheel that is used on the Ender 3 V2 printer but without the small...

________________________________________________________________________ Hello, This knurled adjustment knob design was inspired by the "Knurled Ender 3 V2 Belt Tensioner Knob (Parametric Fusion 360)" by scaryPug & the "Ender 3 V2 Knurling Style...

This is a Direct Drive Mount for an Ender 3 V2. It has the hole for the stock fan shroud and a mount for a BLTouch. V2 added with 2mm spacer for BLtouch to sit lower. Offsets are X-42.0 Y 10.0 It mounts the stepper sideways so that there is no...

This filament guide was designed to help smoothen the flow of filament from the spool to the extruder of the Ender 3 V2 printer. The filament guide comprises of four parts. After printing the parts, they can be easily assembled by press-fitting...

Support for the top of the Z lead screw for the Ender 3 v2 printer. Print instructionsPrinter Brand: Creality Printer: Ender 3 v2</div> Rafts: No Supports: Yes</div> Resolution: 0.16 Infill: 25%</div>

I plan on adding a strain relief mount for the cables and to modify mounting the BL touch.I remixed the parts from the E3d guide from...

First I modified the height to be 35mm without any rubber, because otherwise it would be to short for the Ender v2 Silent Mods. Then I decreased the gap for the rubber to 1mm total. Now you can use any rubber thicker than 1mm. I suggest 3mm and...

... E3d guide from here. https://e3d-online.zendesk.com/hc/en-us/articles/360018062117-Hemera-Ender-3-V2-Ender-3-CR10-CR10-V2-Upgrade-Guide-Edition-2- Also Some minor changes to the parts used in there guide. ... Changed from M3 square nuts to M3 Nuts

Just remove the corner cap, slide it on, and replace the cap. PRINT ORIENTATION is best on it's side like shown in my 2nd pic PLEASE NOTE only tested to work on my Ender 3 V2 as it has taller feet. ...If your Ender 3 or Ender 3 Pro are stock, this might...