ender 3 z stepper motor 3d models

... want to purchase an anti-backlash nut. Simply tightening down the v-rollers is not a good solution by any means. A dual stepper z-axis or dual belted z-axis is not necessary, although is a more expensive alternate solution to an anti-backlash nut.

Also, check out these other mods that dramatically reduce the sound of your Ender 3: * [Y-Axis Stepper Damper](https://www.thingiverse.com/thing:3488452) * [Z-Axis Stepper Damper](https://www.thingiverse.com/thing:3516416) * [Low Profile...

... a decorative purpose. ...It features an endstop mount and wire guide. Designed for printers like the Ender 3, this X motor cover includes a simple end-of-travel stop support and two cable guides to prevent them from colliding with the motor gear.

Ender 3 Z-Axis Stabilizer

Here's a revised remix of the Scuddy Dual Z Upgrade Kit for the Ender 3, tailored specifically for Geeetech A10/A10M printers that utilize a second stepper motor for enhanced dual-axis functionality. To accommodate this upgrade, I've modified the...

It also doesn't require any fiddling with the end stop.NOTE: Does not work on the Ender-3 ProAlso, check out these other mods that dramatically reduce the sound of your Ender 3X-Axis Stepper DamperZ-Axis Stepper DamperLow Profile FeetEnjoy the...

This adapter is as simple as I can make it.Benefits compared to other optionsSimple to installNo firmware changes requiredNo structural compromises (it's attaches to the original metal assembly)The only downside is that it requires 3 x M3*8mm...

The design is intended to work seamlessly with a stepper motor damper on the CR-10, though it can be adapted for other printers as well. To secure the extruder in place, I employed M3 Nuts (x2) at the bottom of the print, each one situated on either...

... mount to allow for easier printing and with alignment ribs to locate it on extrusion more accurately. ... The bottom cutout is to allow the motor terminals to sit along the extrusion rather than sticking out sideways. ... Use M3 screws and T Nuts

Updated Design:2019-03-12 - I released a totally new design that is much simpler and cleaner.Check it out over ➠ hereOriginal Design:When I originally ordered my Ender 3, I also purchased a few stepper motor dampeners. To my dismay, the stepper...

Tarantula bottom mounts for z-axis stepper motors are now ready for single or dual z configuration use. This requires a unique design of the z nut mount due to insufficient space between the nut and motor/coupler. The necessary design is included. ...

I needed an adjustable Z-motor to line up my Z-rod and printed the source file, but unfortunately it was designed for larger size screws. As I required 2 pieces of T-slot-nuts, and all I had on hand were M3 nuts, I created a modified version with...

I needed an adjustable Z-motor to align my Z-rod and printed the source file, only to discover that it was designed for larger screws. As this setup requires 2 pieces of T-slot-nuts, and I only had M3-sized ones, I created a modified version with...

Check out the latest creation over ➠ [here](https://www.thingiverse.com/thing:3488452) ------ **Classic Design:** When I initially ordered my Ender 3, I also picked up a few stepper motor dampeners. To my disappointment, the stepper motors had...

The Axial thrust bearing combined with a rigid lead-screw compression coupler completely eliminates Z-axis banding caused by the stepper motor “wobbling” under the weight of the X-gantry.Do not use Flexible Couplers, the whole point is to remove...

Uses 2x M3x16 1x M4x8 1x T nut Confirmed working for ender 3 but may have for other Creality machines. The stepper motor will sit on the base rail. ... I had to shave off a little of the control box cover to get the z axis to align with the lead screw...

[Ender 3 V2](https://amzn.to/2MddE5f) Y-Axis Stepper Motor Damper Mount remixed from the design by: [Ra1ns](https://www.thingiverse.com/thing:4591114) to fit my specific dampers and provide clearance for full retraction of the Y-axis. My dampers:...

... Compatible with the following 2nd Z-axis lead screw mount: https://www.thingiverse.com/thing:4795281 Required Screws: 1st Stepper motor: 2x 20mm M4 Screws 2x 16mm M3 Screws 2nd Stepper motor: 2x 12mm M4 Screws 2x M4 T-Nuts 2x 16mm M3 Screws

The mount has a 9mm offset so it can be used with larger motors, or stepper motor dampers. My machine is equipped with a 48mm stepper motor which necessitated this mount. This stepper is also mounted ~3mm higher than the stock, which eliminates...

Quick swap time: swapping the mounting holes to fit 5mm screws instead of the smaller 4mm ones I have on hand. All I need are some spare 5mm screws lying around. The hammer nuts required are straightforward - just simple 5mm hammer t-nuts, available...

Upgrading your stock extruder requires a reliable cable holder to keep things organized and within reach.

**Non-Stock Parts Needed - Stock Bracket Replacement** - 1x M8 washer (to place under the eccentric nut so it doesn't wear through the plastic) - Suitable motor (NEMA17, get one like the ones on the Ender 3) **Non-Stock Parts Needed - Second Z...

Customized stepper motor pulley covers for Creality Ender printers.

Ender-3 Z-rail cover preventing filament contamination

This is a cover for Ender-3 Z-end stop.

Customizable motor mounting solutions for Ender3 printers are available, featuring vibration isolators or standard mounts. These adapters fit seamlessly on both sides of the Z-axis, ensuring a secure and stable printing experience. ... Click here to...

... on top of the motor but found them to be problematic. They either obstructed the bed, fitted the stepper motor too tightly and defeated its purpose, or introduced excessive wobble in the stepper motor causing it to misalign the Z-axis lead screw.

Dual Z for Ender 3 V2 without second motor Material needed 2x Pulley GT2 6mm 1x Belt GT2 6mm --> 610mm closed 3 x Roller's --> F688ZZ 1x Lead screw T8 | Pitch 2 mm Lead 8 mm -->400 mm

Human: CNC Plasma Linear Actuator Z Motor Support\r\nThis design is meant to reinforce NEMA23 stepper motors used on the actuator.\r\nThe motor support that came with my purchased actuator consisted of 2 metal tubes, but this setup wasn't...

This will fit stepper motors type 42-34 as found in many kits. ...