ender 3 z offset 3d models

Lock your Z axis for changing filament or while transporting. The 2 holes are not threaded, but meant for M4 tap. 2 screws, M4 X 12 are used to connect the 2 pieces. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No...

And the original bed is better for PTEG.But without autoLeveling is very difficult to change the bed's between materials.So i found a design to adjust the Z EndStop and add spacer ability to quick change the bed's.I used the EndStopCover to develop...

Ender 3 Z-motor Clamp ===================== Why I Designed This ------------------- The Ender 3's motormount, located on a single top edge of the Z-motor, often results in the motor being tilted away at the bottom. This causes the motor axle and...

Remix of Ender 3 mount, the original was fouling with X gantry on my setup. ...so remixed a bit slimmer one, still works with T-Nuts.

Z endstop mount

The Optic Endstop is a crucial component on the Zender 3 that helps maintain precise control over the printer's movement, particularly when it comes to the Z-axis. ...This device is tasked with detecting the physical limit of the Z-axis, thereby...

I recently printed someone's Z axis adjustment parts for the Ender 3, and noticed some issues I had with it, so I design my own. My design has some nice features, like the X axis cover uses 2 of the original screws to hold it in place, and the mount...

This is a remix of thing:2725795. ...I didn't have a 3 x 30 mm screw so I remixed it for a 4 x 30mm. ...I also added a thumb screw so I could lock the Z stop.

My new Ender-3 arrived today, and the nut for the Z lead screw rod is missing threads as if it was not tapped. It should be T8 trapezoidal threads with 2mm pitch; if that's true, this should work (amusing my first try at Fusion 360 was done...

Wiring: So far, I've only tested wiring a second stepper in parallel with the original stepper, increasing current to 1 amp (Skr 1.3 with 2208). Also, my second stepper is different from the original Creality stepper, which isn't recommended. I'll...

I remixed mlynch002's design because I wanted my printer in the original location, so my ender would fit better on my desk after adding the dual Z screw. I highly recommend the dual Z upgrade, and my remix uses about half the filament and print time...

I remixed mlynch002 because I wanted my in the original location and so my ender would fit better on my desk after the dual Z screw was added. Would highly recommend the dual z, and my remix of his design uses about half the filament / print time,...

I modified the bracket from the original design here: https://www.thingiverse.com/thing:2757810 to fit the Ender-3 printer by shortening it in Blender using the STL file. To assemble, you'll need to print nine link_top.stl parts and nine...

Adjustable end stop for the Z axis.

I combined the original design with z rod holders from Aliexpress: https://www.aliexpress.com/item/33013348068.html. The design doesn't restrict Z-axis movement! To assemble, use Cura to mirror both parts for the left side. Cut a 1-meter M10 rod...

This is a remix using tinkercad.com to remove a 30x3 mm section to wrap around the x-axis belt tensioner on my Ender 3 v2. The tensioner sticks out so the part that takes the place of the spacers can not lay flat without removing some of the part. ... ...

Hardware: 4 - M3x10mm screws 3 - M4x8mm screws 3 - M4 T-nuts Helpful Tips: ALL filament shrinks after cooling. The amount of shrinkage depends on the type of filament. PLA shrinks about 0.25% PetG shrinks around 0.35% Taulman 910 shrinks 0.31% That...

Parts: KLF08 Bearings: https://de.aliexpress.com/item/32793159224.html Ender 3 Rod: https://de.aliexpress.com/item/32904246004.html GT2 Timing Pulley: https://de.aliexpress.com/item/33017482340.html GT2 Belt Joining:...

Replacement for Creality part. ...Allows adjustment of z-screw position.

To examine the calibration of the bed plate along the Z-axis; To inspect Z leveling on heated surface

To verify the calibration of the Z-axis on the heated bed; Verify z-level on hotbed

Reminder for the movement of the Nozzle up or down (Z-Axis)

The Z-axis Test 1 utilizes materials from the Model LM8UU.

The human shields the filament from damage caused by a collision with the z-axis rod.

The spiral shape is getting a slight upgrade to fit on the Z knob. ...This updated design is also slightly thicker, which should allow it to clear out most of those pesky z-axis stabilizers.

The knob is designated for use with the Ender3/ender3 pro z-axis print model. ...It features a prominent label with the letter "Z" clearly printed at the top.

A tiny tweak to https://www.thingiverse.com/thing:3080912 gets my printer's Z-axis running smoothly.

And instead of a ball bearing that fixes the z-axis, I designed an alternative ring that gives the z-axis room to wobble, but still protects against bending. Assembly is easy: slide the base of the stabilizer into the top profile. There is no need...

This is a straightforward Z-axis stabilizer without bearings designed to prevent loss of print height, and it's suitable for dual-drive extruders as well.

The human plays a crucial role in maintaining the structural integrity of the Z Rod by keeping it properly aligned and stable.